ath79: add support for Compex WPJ531 (16M)
[openwrt/staging/dedeckeh.git] / target / linux / ath79 / dts / ar7240_tplink.dtsi
1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2
3 #include <dt-bindings/gpio/gpio.h>
4 #include <dt-bindings/input/input.h>
5
6 #include "ar7240.dtsi"
7
8 / {
9 aliases {
10 led-boot = &led_system;
11 led-failsafe = &led_system;
12 led-running = &led_system;
13 led-upgrade = &led_system;
14 label-mac-device = &ath9k;
15 };
16
17 keys {
18 compatible = "gpio-keys";
19
20 reset {
21 label = "reset";
22 linux,code = <KEY_RESTART>;
23 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
24 debounce-interval = <60>;
25 };
26
27 wps {
28 label = "wps";
29 linux,code = <KEY_WPS_BUTTON>;
30 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
31 debounce-interval = <60>;
32 };
33 };
34
35 leds: leds {
36 compatible = "gpio-leds";
37
38 pinctrl-names = "default";
39 pinctrl-0 = <&pinmux_switch_led_pins>;
40
41 led_system: system {
42 label = "tp-link:green:system";
43 gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
44 };
45
46 qss {
47 label = "tp-link:green:qss";
48 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
49 };
50 };
51
52 ath9k-leds {
53 compatible = "gpio-leds";
54
55 wlan {
56 label = "tp-link:green:wlan";
57 gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
58 linux,default-trigger = "phy0tpt";
59 };
60 };
61 };
62
63 &spi {
64 status = "okay";
65
66 num-cs = <1>;
67
68 flash@0 {
69 compatible = "jedec,spi-nor";
70 reg = <0>;
71 spi-max-frequency = <25000000>;
72
73 partitions {
74 compatible = "fixed-partitions";
75 #address-cells = <1>;
76 #size-cells = <1>;
77
78 uboot: partition@0 {
79 reg = <0x0 0x20000>;
80 label = "u-boot";
81 read-only;
82 };
83
84 partition@20000 {
85 compatible = "tplink,firmware";
86 reg = <0x20000 0x3d0000>;
87 label = "firmware";
88 };
89
90 art: partition@3f0000 {
91 reg = <0x3f0000 0x10000>;
92 label = "art";
93 read-only;
94 };
95 };
96 };
97 };
98
99 &eth1 {
100 status = "okay";
101 };
102
103 &pcie {
104 status = "okay";
105
106 ath9k: wifi@0,0 {
107 reg = <0x0000 0 0 0 0>;
108 qca,no-eeprom;
109 mtd-mac-address = <&uboot 0x1fc00>;
110 #gpio-cells = <2>;
111 gpio-controller;
112 };
113 };
114
115 &pinmux {
116 pinmux_switch_led_pins: switch_led_pins {
117 pinctrl-single,bits = <0x0 0x0 0xf8>;
118 };
119 };
120
121 &uart {
122 status = "okay";
123 };