target/linux/ath79/dts/ar9330_dlink_dir-505.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "D-Link DIR-505";
  11         compatible = "dlink,dir-505", "qca,ar9330";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-boot = &led_power_green;
  16                 led-failsafe = &led_status_red;
  17                 led-running = &led_power_green;
  18                 led-upgrade = &led_status_red;
  19         };
  20
  21         keys {
  22                 compatible = "gpio-keys";
  23
  24                 wps {
  25                         label = "WPS button";
  26                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  27                         linux,code = <KEY_WPS_BUTTON>;
  28                 };
  29
  30                 reset {
  31                         label = "Reset button";
  32                         gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
  33                         linux,code = <KEY_RESTART>;
  34                 };
  35         };
  36
  37         leds {
  38                 compatible = "gpio-leds";
  39                 pinctrl-names = "default";
  40                 pinctrl-0 = <&jtag_disable_pins>;
  41
  42                 led_power_green: power {
  43                         label = "d-link:green:power";
  44                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  45                 };
  46
  47                 led_status_red: status {
  48                         label = "d-link:red:status";
  49                         gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
  50                 };
  51         };
  52 };
  53
  54 &uart {
  55         status = "okay";
  56 };
  57
  58 &gpio {
  59         status = "okay";
  60
  61         led_enable {
  62                 gpio-hog;
  63                 output-low;
  64                 gpios = <1 GPIO_ACTIVE_LOW>;
  65                 line-name = "d-link:power:led";
  66         };
  67 };
  68
  69 &usb {
  70         dr_mode = "host";
  71         status = "okay";
  72 };
  73
  74 &usb_phy {
  75         status = "okay";
  76 };
  77
  78 &eth0 {
  79         status = "okay";
  80
  81         gmac-config {
  82                 device = <&gmac>;
  83                 switch-phy-addr-swap = <0>;
  84                 switch-phy-swap = <0>;
  85         };
  86 };
  87
  88 &eth1 {
  89         compatible = "syscon", "simple-mfd";
  90         status = "okay";
  91 };
  92
  93 &spi {
  94         num-chipselects = <1>;
  95         status = "okay";
  96
  97         flash@0 {
  98                 compatible = "jedec,spi-nor";
  99                 spi-max-frequency = <50000000>;
 100                 reg = <0>;
 101
 102                 partitions {
 103                         compatible = "fixed-partitions";
 104                         #address-cells = <1>;
 105                         #size-cells = <1>;
 106
 107                         partition@0 {
 108                                 label = "u-boot";
 109                                 reg = <0x0 0x10000>;
 110                                 read-only;
 111                         };
 112
 113                         art: partition@10000 {
 114                                 label = "art";
 115                                 reg = <0x10000 0x10000>;
 116                                 read-only;
 117                         };
 118
 119                         mac: partition@20000 {
 120                                 label = "mac";
 121                                 reg = <0x20000 0x10000>;
 122                                 read-only;
 123                         };
 124
 125                         partition@30000 {
 126                                 label = "nvram";
 127                                 reg = <0x30000 0x10000>;
 128                                 read-only;
 129                         };
 130
 131                         partition@40000 {
 132                                 label = "language";
 133                                 reg = <0x40000 0x40000>;
 134                                 read-only;
 135                         };
 136
 137                         partition@80000 {
 138                                 compatible = "denx,uimage";
 139                                 label = "firmware";
 140                                 reg = <0x80000 0x780000>;
 141                         };
 142                 };
 143         };
 144 };
 145
 146 &wmac {
 147         status = "okay";
 148         qca,no-eeprom;
 149 };