target/linux/ath79/dts/ar9330_glinet_gl-ar150.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "GL.iNet GL-AR150";
  11         compatible = "glinet,gl-ar150", "qca,ar9330";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-boot = &led_power;
  16                 led-failsafe = &led_power;
  17                 led-running = &led_power;
  18                 led-upgrade = &led_power;
  19                 label-mac-device = &eth0;
  20         };
  21
  22         leds {
  23                 compatible = "gpio-leds";
  24
  25                 wlan {
  26                         label = "gl-ar150:orange:wlan";
  27                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  28                         linux,default-trigger = "phy0tpt";
  29                 };
  30
  31                 configurable {
  32                         label = "gl-ar150:green:configurable";
  33                         gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
  34                 };
  35
  36                 led_power: power {
  37                         label = "gl-ar150:green:power";
  38                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  39                         default-state = "on";
  40                 };
  41         };
  42
  43         keys {
  44                 compatible = "gpio-keys";
  45
  46                 manual {
  47                         label = "manual";
  48                         linux,code = <BTN_7>;
  49                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  50                 };
  51
  52                 auto {
  53                         label = "auto";
  54                         linux,code = <BTN_8>;
  55                         gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
  56                 };
  57
  58                 reset {
  59                         label = "reset";
  60                         linux,code = <KEY_RESTART>;
  61                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  62                 };
  63         };
  64 };
  65
  66 &uart {
  67         status = "okay";
  68 };
  69
  70 &gpio {
  71         status = "okay";
  72 };
  73
  74 &usb {
  75         dr_mode = "host";
  76         status = "okay";
  77 };
  78
  79 &usb_phy {
  80         status = "okay";
  81         gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
  82 };
  83
  84 &spi {
  85         status = "okay";
  86
  87         num-chipselects = <1>;
  88
  89         flash@0 {
  90                 compatible = "jedec,spi-nor";
  91                 spi-max-frequency = <50000000>;
  92                 reg = <0>;
  93
  94                 partitions {
  95                         compatible = "fixed-partitions";
  96                         #address-cells = <1>;
  97                         #size-cells = <1>;
  98
  99                         partition@0 {
 100                                 label = "u-boot";
 101                                 reg = <0x000000 0x040000>;
 102                                 read-only;
 103                         };
 104
 105                         partition@1 {
 106                                 label = "u-boot-env";
 107                                 reg = <0x040000 0x010000>;
 108                         };
 109
 110                         partition@2 {
 111                                 compatible = "denx,uimage";
 112                                 label = "firmware";
 113                                 reg = <0x050000 0xfa0000>;
 114                         };
 115
 116                         art: partition@3 {
 117                                 label = "art";
 118                                 reg = <0xff0000 0x010000>;
 119                                 read-only;
 120                         };
 121                 };
 122         };
 123 };
 124
 125 &eth0 {
 126         status = "okay";
 127
 128         mtd-mac-address = <&art 0x0>;
 129 };
 130
 131 &eth1 {
 132         status = "okay";
 133
 134         mtd-mac-address = <&art 0x0>;
 135
 136         gmac-config {
 137                 device = <&gmac>;
 138
 139                 switch-phy-addr-swap = <0>;
 140                 switch-phy-swap = <0>;
 141         };
 142 };
 143
 144 &wmac {
 145         status = "okay";
 146
 147         mtd-cal-data = <&art 0x1000>;
 148         mtd-mac-address = <&art 0x0>;
 149 };