target/linux/ath79/dts/ar9331_pisen_ts-d084.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9331.dtsi"
   8
   9 / {
  10         model = "Pisen TS-D084";
  11         compatible = "pisen,ts-d084", "qca,ar9331";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-boot = &led_system;
  16                 led-failsafe = &led_system;
  17                 led-running = &led_system;
  18                 led-upgrade = &led_system;
  19                 label-mac-device = &wmac;
  20         };
  21
  22         keys {
  23                 compatible = "gpio-keys";
  24
  25                 reset {
  26                         label = "reset";
  27                         linux,code = <KEY_RESTART>;
  28                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  29                         debounce-interval = <60>;
  30                 };
  31         };
  32
  33         leds {
  34                 compatible = "gpio-leds";
  35
  36                 led_system: system {
  37                         label = "ts-d084:blue:system";
  38                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  39                 };
  40         };
  41 };
  42
  43 &spi {
  44         status = "okay";
  45
  46         flash@0 {
  47                 compatible = "jedec,spi-nor";
  48                 reg = <0>;
  49                 spi-max-frequency = <25000000>;
  50
  51                 partitions {
  52                         compatible = "fixed-partitions";
  53                         #address-cells = <1>;
  54                         #size-cells = <1>;
  55
  56                         uboot: partition@0 {
  57                                 reg = <0x0 0x20000>;
  58                                 label = "u-boot";
  59                                 read-only;
  60                         };
  61
  62                         firmware: partition@20000 {
  63                                 compatible = "tplink,firmware";
  64                                 reg = <0x20000 0x7d0000>;
  65                                 label = "firmware";
  66                         };
  67
  68                         art: partition@7f0000 {
  69                                 reg = <0x7f0000 0x10000>;
  70                                 label = "art";
  71                                 read-only;
  72                         };
  73                 };
  74         };
  75 };
  76
  77 &eth0 {
  78         status = "okay";
  79
  80         mtd-mac-address = <&uboot 0x1fc00>;
  81
  82         gmac-config {
  83                 device = <&gmac>;
  84
  85                 switch-phy-addr-swap = <0>;
  86                 switch-phy-swap = <0>;
  87         };
  88 };
  89
  90 &eth1 {
  91         status = "okay";
  92         compatible = "syscon", "simple-mfd";
  93 };
  94
  95 &gpio {
  96         status = "okay";
  97 };
  98
  99 &uart {
 100         status = "okay";
 101 };
 102
 103 &usb {
 104         dr_mode = "host";
 105         status = "okay";
 106 };
 107
 108 &usb_phy {
 109         status = "okay";
 110 };
 111
 112 &wmac {
 113         status = "okay";
 114         mtd-cal-data = <&art 0x1000>;
 115         mtd-mac-address = <&uboot 0x1fc00>;
 116 };