target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi

   1
   2 #include <dt-bindings/gpio/gpio.h>
   3 #include <dt-bindings/input/input.h>
   4
   5 #include "qca953x.dtsi"
   6
   7 / {
   8         aliases {
   9                 led-boot = &led_status;
  10                 led-failsafe = &led_status;
  11                 led-running = &led_status;
  12                 led-upgrade = &led_status;
  13                 label-mac-device = &eth0;
  14         };
  15
  16         keys {
  17                 compatible = "gpio-keys";
  18
  19                 pinctrl-names = "default";
  20                 pinctrl-0 = <&jtag_disable_pins>;
  21
  22                 reset {
  23                         label = "reset";
  24                         linux,code = <KEY_RESTART>;
  25                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  26                 };
  27
  28                 right {
  29                         label = "button right";
  30                         linux,code = <BTN_0>;
  31                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  32                 };
  33
  34                 left {
  35                         label = "button left";
  36                         linux,code = <BTN_1>;
  37                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  38                 };
  39         };
  40
  41         leds {
  42                 compatible = "gpio-leds";
  43
  44                 // Colors for non-Lite versions
  45
  46                 led_status: status {
  47                         label = "gl-ar300m:green:status";
  48                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  49                 };
  50
  51                 led_lan: lan {
  52                         label = "gl-ar300m:green:lan";
  53                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  54                 };
  55
  56                 led_wlan: wlan {
  57                         label = "gl-ar300m:red:wlan";
  58                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  59                         linux,default-trigger = "phy0tpt";
  60                 };
  61         };
  62
  63         i2c: i2c {
  64                 compatible = "i2c-gpio";
  65
  66                 sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  67                 scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  68         };
  69 };
  70
  71 &pcie0 {
  72         status = "okay";
  73 };
  74
  75 &spi {
  76         status = "okay";
  77
  78         num-cs = <2>;
  79
  80         flash@0 {
  81                 compatible = "jedec,spi-nor";
  82                 reg = <0>;
  83                 spi-max-frequency = <25000000>;
  84
  85                 partitions {
  86                         compatible = "fixed-partitions";
  87                         #address-cells = <1>;
  88                         #size-cells = <1>;
  89
  90                         partition@0 {
  91                                 label = "u-boot";
  92                                 reg = <0x000000 0x040000>;
  93                                 read-only;
  94                         };
  95
  96                         partition@40000 {
  97                                 label = "u-boot-env";
  98                                 reg = <0x040000 0x010000>;
  99                         };
 100
 101                         nor_firmware: partition@50000 {
 102                                 label = "nor_firmware";
 103                                 reg = <0x050000 0xfa0000>;
 104                         };
 105
 106                         art: partition@ff0000 {
 107                                 label = "art";
 108                                 reg = <0xff0000 0x010000>;
 109                                 read-only;
 110                         };
 111                 };
 112         };
 113
 114         nand_flash: flash@1 {
 115                 compatible = "spi-nand";
 116                 reg = <1>;
 117                 spi-max-frequency = <25000000>;
 118
 119                 partitions {
 120                         compatible = "fixed-partitions";
 121                         #address-cells = <1>;
 122                         #size-cells = <1>;
 123
 124                         nand_kernel: partition@0 {
 125                                 label = "nand_kernel";
 126                                 reg = <0x000000 0x400000>;
 127                         };
 128
 129                         nand_ubi: partition@400000 {
 130                                 label = "nand_ubi";
 131                                 reg = <0x400000 0x7c00000>;
 132                         };
 133                 };
 134         };
 135 };
 136
 137 &uart {
 138         status = "okay";
 139 };
 140
 141 &usb0 {
 142         #address-cells = <1>;
 143         #size-cells = <0>;
 144         status = "okay";
 145 };
 146
 147 &usb_phy {
 148         status = "okay";
 149 };
 150
 151 &eth0 {
 152         status = "okay";
 153         mtd-mac-address = <&art 0x0>;
 154         phy-handle = <&swphy4>;
 155 };
 156
 157 &eth1 {
 158         mtd-mac-address = <&art 0x0>;
 159         mtd-mac-address-increment = <1>;
 160 };
 161
 162 &wmac {
 163         status = "okay";
 164         mtd-cal-data = <&art 0x1000>;
 165 };