target/linux/ath79/dts/qca9533_tplink_tl-wa801nd.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca953x.dtsi"
   7
   8 / {
   9         aliases {
  10                 label-mac-device = &wmac;
  11                 led-boot = &led_system;
  12                 led-failsafe = &led_system;
  13                 led-running = &led_system;
  14                 led-upgrade = &led_system;
  15         };
  16
  17         leds {
  18                 compatible = "gpio-leds";
  19
  20                 lan {
  21                         label = "tp-link:green:lan";
  22                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  23                 };
  24
  25                 security_red {
  26                         label = "tp-link:red:security";
  27                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  28                 };
  29
  30                 wlan {
  31                         label = "tp-link:green:wlan";
  32                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  33                         linux,default-trigger = "phy0tpt";
  34                 };
  35
  36                 led_system: system {
  37                         label = "tp-link:green:system";
  38                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  39                 };
  40
  41                 security_green {
  42                         label = "tp-link:green:security";
  43                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  44                 };
  45         };
  46
  47         keys {
  48                 compatible = "gpio-keys";
  49
  50                 reset {
  51                         label = "Reset button";
  52                         linux,code = <KEY_RESTART>;
  53                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  54                         debounce-interval = <60>;
  55                 };
  56
  57                 wps {
  58                         label = "WPS button";
  59                         linux,code = <KEY_WPS_BUTTON>;
  60                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  61                         debounce-interval = <60>;
  62                 };
  63         };
  64 };
  65
  66 &uart {
  67         status = "okay";
  68 };
  69
  70 &spi {
  71         status = "okay";
  72
  73         num-cs = <1>;
  74
  75         flash@0 {
  76                 compatible = "jedec,spi-nor";
  77                 reg = <0>;
  78                 spi-max-frequency = <25000000>;
  79
  80                 partitions {
  81                         compatible = "fixed-partitions";
  82                         #address-cells = <1>;
  83                         #size-cells = <1>;
  84
  85                         uboot: partition@0 {
  86                                 label = "u-boot";
  87                                 reg = <0x000000 0x020000>;
  88                                 read-only;
  89                         };
  90
  91                         partition@20000 {
  92                                 compatible = "tplink,firmware";
  93                                 label = "firmware";
  94                                 reg = <0x020000 0x3d0000>;
  95                         };
  96
  97                         art: partition@3f0000 {
  98                                 label = "art";
  99                                 reg = <0x3f0000 0x010000>;
 100                                 read-only;
 101                         };
 102                 };
 103         };
 104 };
 105
 106 &eth0 {
 107         status = "okay";
 108
 109         phy-handle = <&swphy4>;
 110
 111         mtd-mac-address = <&uboot 0x1fc00>;
 112 };
 113
 114 &eth1 {
 115         compatible = "syscon", "simple-mfd";
 116 };
 117
 118 &wmac {
 119         status = "okay";
 120
 121         mtd-cal-data = <&art 0x1000>;
 122         mtd-mac-address = <&uboot 0x1fc00>;
 123 };