target/linux/ath79/dts/qca9558_ocedo_koala.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca955x.dtsi"
   8
   9 / {
  10         compatible = "ocedo,koala", "qca,qca9558";
  11         model = "OCEDO Koala";
  12
  13         aliases {
  14                 led-boot = &led_system;
  15                 led-failsafe = &led_system;
  16                 led-running = &led_system;
  17                 led-upgrade = &led_system;
  18                 label-mac-device = &eth0;
  19         };
  20
  21         leds {
  22                 compatible = "gpio-leds";
  23
  24                 power {
  25                         label = "koala:green:power";
  26                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  27                         default-state = "on";
  28                 };
  29
  30                 wifi2 {
  31                         label = "koala:yellow:wlan2";
  32                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  33                         linux,default-trigger = "phy1tpt";
  34                 };
  35
  36                 wifi5 {
  37                         label = "koala:red:wlan58";
  38                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  39                         linux,default-trigger = "phy0tpt";
  40                 };
  41
  42                 led_system: system {
  43                         label = "koala:blue:sys";
  44                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  45                 };
  46         };
  47
  48         keys {
  49                 compatible = "gpio-keys";
  50
  51                 reset {
  52                         label = "reset";
  53                         linux,code = <KEY_RESTART>;
  54                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  55                 };
  56         };
  57 };
  58
  59 &pcie0 {
  60         status = "okay";
  61 };
  62
  63 &uart {
  64         status = "okay";
  65 };
  66
  67 &pll {
  68         clocks = <&extosc>;
  69 };
  70
  71 &spi {
  72         status = "okay";
  73         num-cs = <1>;
  74
  75         flash@0 {
  76                 compatible = "jedec,spi-nor";
  77                 reg = <0>;
  78                 spi-max-frequency = <25000000>;
  79
  80                 partitions {
  81                         compatible = "fixed-partitions";
  82                         #address-cells = <1>;
  83                         #size-cells = <1>;
  84
  85                         uboot: partition@0 {
  86                                 label = "u-boot";
  87                                 reg = <0x000000 0x040000>;
  88                                 read-only;
  89                         };
  90
  91                         partition@40000 {
  92                                 label = "u-boot-env";
  93                                 reg = <0x040000 0x010000>;
  94                         };
  95
  96                         partition@50000 {
  97                                 compatible = "denx,uimage";
  98                                 label = "firmware";
  99                                 reg = <0x050000 0x740000>;
 100                         };
 101
 102                         partition@790000 {
 103                                 label = "vendor";
 104                                 reg = <0x790000 0x740000>;
 105                                 read-only;
 106                         };
 107
 108                         partition@ed0000 {
 109                                 label = "data";
 110                                 reg = <0xed0000 0x110000>;
 111                                 read-only;
 112                         };
 113
 114                         partition@fe0000 {
 115                                 label = "id";
 116                                 reg = <0xfe0000 0x010000>;
 117                                 read-only;
 118                         };
 119
 120                         art: partition@ff0000 {
 121                                 label = "art";
 122                                 reg = <0xff0000 0x010000>;
 123                                 read-only;
 124                         };
 125                 };
 126         };
 127 };
 128
 129 &wmac {
 130         status = "okay";
 131
 132         mtd-cal-data = <&art 0x1000>;
 133         mtd-mac-address = <&art 0x06>;
 134 };
 135
 136 &mdio0 {
 137         status = "okay";
 138
 139         phy5: ethernet-phy@5 {
 140                 reg = <5>;
 141                 eee-broken-100tx;
 142                 eee-broken-1000t;
 143         };
 144 };
 145
 146 &eth0 {
 147         status = "okay";
 148
 149         mtd-mac-address = <&art 0x00>;
 150
 151         phy-handle = <&phy5>;
 152         phy-mode = "rgmii-rxid";
 153
 154         pll-data = <0x8e000000 0x80000101 0x80001313>;
 155 };