target/linux/ath79/dts/qca9558_tplink_tl-wdr4900-v2.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca955x.dtsi"
   8
   9 / {
  10         compatible = "tplink,tl-wdr4900-v2", "qca,qca9558";
  11         model = "TP-Link TL-WDR4900 v2";
  12
  13         aliases {
  14                 led-boot = &led_system;
  15                 led-failsafe = &led_system;
  16                 led-running = &led_system;
  17                 led-upgrade = &led_system;
  18                 label-mac-device = &eth1;
  19         };
  20
  21         leds {
  22                 compatible = "gpio-leds";
  23
  24                 led_system: system {
  25                         label = "tp-link:blue:system";
  26                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  27                         default-state = "on";
  28                 };
  29
  30                 usb1 {
  31                         label = "tp-link:green:usb1";
  32                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  33                         trigger-sources = <&hub_port1>;
  34                         linux,default-trigger = "usbport";
  35                 };
  36
  37                 usb2 {
  38                         label = "tp-link:green:usb2";
  39                         gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
  40                         trigger-sources = <&hub_port0>;
  41                         linux,default-trigger = "usbport";
  42                 };
  43
  44                 wlan2g {
  45                         label = "tp-link:blue:wlan2g";
  46                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  47                         linux,default-trigger = "phy0tpt";
  48                 };
  49
  50                 qss {
  51                         label = "tp-link:blue:qss";
  52                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  53                 };
  54         };
  55
  56         ath9k-leds {
  57                 compatible = "gpio-leds";
  58
  59                 wlan5g {
  60                         label = "tp-link:blue:wlan5g";
  61                         gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
  62                         linux,default-trigger = "phy1tpt";
  63                 };
  64         };
  65
  66         keys {
  67                 compatible = "gpio-keys";
  68
  69                 reset {
  70                         label = "Reset button";
  71                         linux,code = <KEY_RESTART>;
  72                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  73                         debounce-interval = <60>;
  74                 };
  75         };
  76
  77         gpio-export {
  78                 compatible = "gpio-export";
  79
  80                 gpio_usb1_power {
  81                         gpio-export,name = "tp-link:power:usb1";
  82                         gpio-export,output = <1>;
  83                         gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
  84                 };
  85
  86                 gpio_usb2_power {
  87                         gpio-export,name = "tp-link:power:usb2";
  88                         gpio-export,output = <1>;
  89                         gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
  90                 };
  91         };
  92 };
  93
  94 &pcie1 {
  95         status = "okay";
  96
  97         ath9k: wifi@0,0 {
  98                 compatible = "pci168c,0033";
  99                 reg = <0x0000 0 0 0 0>;
 100                 mtd-mac-address = <&uboot 0x1fc00>;
 101                 mtd-mac-address-increment = <(-2)>;
 102                 qca,no-eeprom;
 103                 #gpio-cells = <2>;
 104                 gpio-controller;
 105         };
 106 };
 107
 108 &uart {
 109         status = "okay";
 110 };
 111
 112 &usb_phy0 {
 113         status = "okay";
 114 };
 115
 116 &usb0 {
 117         #address-cells = <1>;
 118         #size-cells = <0>;
 119         status = "okay";
 120
 121         hub_port0: port@1 {
 122                 reg = <1>;
 123                 #trigger-source-cells = <0>;
 124         };
 125 };
 126
 127 &usb_phy1 {
 128         status = "okay";
 129 };
 130
 131 &usb1 {
 132         #address-cells = <1>;
 133         #size-cells = <0>;
 134         status = "okay";
 135
 136         hub_port1: port@1 {
 137                 reg = <1>;
 138                 #trigger-source-cells = <0>;
 139         };
 140 };
 141
 142 &spi {
 143         status = "okay";
 144
 145         num-cs = <1>;
 146
 147         flash@0 {
 148                 compatible = "jedec,spi-nor";
 149                 reg = <0>;
 150                 spi-max-frequency = <25000000>;
 151
 152                 partitions {
 153                         compatible = "fixed-partitions";
 154                         #address-cells = <1>;
 155                         #size-cells = <1>;
 156
 157                         uboot: partition@0 {
 158                                 label = "u-boot";
 159                                 reg = <0x000000 0x020000>;
 160                                 read-only;
 161                         };
 162
 163                         partition@20000 {
 164                                 compatible = "tplink,firmware";
 165                                 label = "firmware";
 166                                 reg = <0x020000 0x7d0000>;
 167                         };
 168
 169                         art: partition@7f0000 {
 170                                 label = "art";
 171                                 reg = <0x7f0000 0x010000>;
 172                                 read-only;
 173                         };
 174                 };
 175         };
 176 };
 177
 178 &mdio0 {
 179         status = "okay";
 180
 181         phy0: ethernet-phy@0 {
 182                 reg = <0>;
 183
 184                 qca,ar8327-initvals = <
 185                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 186                         0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
 187                         0x50 0xc737c737 /* LED_CTRL0 */
 188                         0x54 0x00000000 /* LED_CTRL1 */
 189                         0x58 0x00000000 /* LED_CTRL2 */
 190                         0x5c 0x0030c300 /* LED_CTRL3 */
 191                         0x7c 0x0000007e /* PORT0_STATUS */
 192                         0x94 0x0000007e /* PORT6 STATUS */
 193                 >;
 194         };
 195 };
 196
 197 &eth0 {
 198         status = "okay";
 199
 200         mtd-mac-address = <&uboot 0x1fc00>;
 201         mtd-mac-address-increment = <1>;
 202         phy-handle = <&phy0>;
 203         pll-data = <0x56000000 0x00000101 0x00001616>;
 204
 205         gmac-config {
 206                 device = <&gmac>;
 207                 rgmii-enabled = <1>;
 208         };
 209 };
 210
 211 &eth1 {
 212         status = "okay";
 213
 214         mtd-mac-address = <&uboot 0x1fc00>;
 215         pll-data = <0x03000101 0x00000101 0x00001616>;
 216
 217         fixed-link {
 218                 speed = <1000>;
 219                 full-duplex;
 220         };
 221 };
 222
 223 &wmac {
 224         status = "okay";
 225
 226         mtd-cal-data = <&art 0x1000>;
 227         mtd-mac-address = <&uboot 0x1fc00>;
 228         mtd-mac-address-increment = <(-1)>;
 229 };