target/linux/ath79/dts/qca9558_trendnet_tew-823dru.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca955x.dtsi"
   8
   9 / {
  10         compatible = "trendnet,tew-823dru", "qca,qca9558";
  11         model = "TRENDNET TEW-823DRU";
  12
  13         aliases {
  14                 led-boot = &led_power_green;
  15                 led-failsafe = &led_power_green;
  16                 led-running = &led_power_green;
  17                 led-upgrade = &led_power_green;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 power_orange {
  24                         label = "trendnet:orange:power";
  25                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  26                 };
  27
  28                 led_power_green: power_green {
  29                         label = "trendnet:green:power";
  30                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  31                 };
  32
  33                 planet_green {
  34                         label = "trendnet:green:planet";
  35                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  36                 };
  37
  38                 planet_orange {
  39                         label = "trendnet:orange:planet";
  40                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  41                 };
  42         };
  43
  44         keys {
  45                 compatible = "gpio-keys";
  46
  47                 reset {
  48                         label = "Reset button";
  49                         linux,code = <KEY_RESTART>;
  50                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  51                         debounce-interval = <60>;
  52                 };
  53
  54                 wps {
  55                         label = "WPS button";
  56                         linux,code = <KEY_WPS_BUTTON>;
  57                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  58                         debounce-interval = <60>;
  59                 };
  60         };
  61 };
  62
  63 &pcie0 {
  64         status = "okay";
  65 };
  66
  67 &pcie1 {
  68         status = "okay";
  69 };
  70
  71 &uart {
  72         status = "okay";
  73 };
  74
  75 &gpio {
  76         status = "okay";
  77 };
  78
  79 &usb_phy0 {
  80         status = "okay";
  81 };
  82
  83 &usb0 {
  84         #address-cells = <1>;
  85         #size-cells = <0>;
  86         status = "okay";
  87
  88         hub_port0: port@1 {
  89                 reg = <1>;
  90                 #trigger-source-cells = <0>;
  91         };
  92 };
  93
  94 &usb_phy1 {
  95         status = "okay";
  96 };
  97
  98 &usb1 {
  99         #address-cells = <1>;
 100         #size-cells = <0>;
 101         status = "okay";
 102
 103         hub_port1: port@1 {
 104                 reg = <1>;
 105                 #trigger-source-cells = <0>;
 106         };
 107 };
 108
 109 &spi {
 110         status = "okay";
 111
 112         num-cs = <1>;
 113
 114         flash@0 {
 115                 compatible = "jedec,spi-nor";
 116                 reg = <0>;
 117                 spi-max-frequency = <25000000>;
 118
 119                 partitions {
 120                         compatible = "fixed-partitions";
 121                         #address-cells = <1>;
 122                         #size-cells = <1>;
 123
 124                         partition@0 {
 125                                 label = "u-boot";
 126                                 reg = <0x000000 0x030000>;
 127                                 read-only;
 128                         };
 129
 130                         partition@30000 {
 131                                 label = "nvram";
 132                                 reg = <0x030000 0x010000>;
 133                                 read-only;
 134                         };
 135
 136                         partition@40000 {
 137                                 compatible = "denx,uimage";
 138                                 label = "firmware";
 139                                 reg = <0x040000 0xef0000>;
 140                         };
 141
 142                         partition@f30000 {
 143                                 label = "lang";
 144                                 reg = <0xf30000 0x030000>;
 145                                 read-only;
 146                         };
 147
 148                         partition@f60000 {
 149                                 label = "my-dlink";
 150                                 reg = <0xf60000 0x080000>;
 151                                 read-only;
 152                         };
 153
 154                         partition@fe0000 {
 155                                 label = "mac";
 156                                 reg = <0xfe0000 0x010000>;
 157                                 read-only;
 158                         };
 159
 160                         art: partition@ff0000 {
 161                                 label = "art";
 162                                 reg = <0xff0000 0x010000>;
 163                                 read-only;
 164                         };
 165                 };
 166         };
 167 };
 168
 169 &mdio0 {
 170         status = "okay";
 171
 172         phy0: ethernet-phy@0 {
 173                 reg = <0>;
 174                 qca,ar8327-initvals = <
 175                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 176                         0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
 177                         0x10 0x81000080 /* POWER_ON_STRIP */
 178                         0x7c 0x0000007e /* PORT0_STATUS */
 179                         0x94 0x0000007e /* PORT6 STATUS */
 180                 >;
 181         };
 182 };
 183
 184 &eth0 {
 185         status = "okay";
 186
 187         phy-handle = <&phy0>;
 188         pll-data = <0x56000000 0x00000101 0x00001616>;
 189
 190         gmac-config {
 191                 device = <&gmac>;
 192                 rgmii-enabled = <1>;
 193         };
 194 };
 195
 196 &eth1 {
 197         status = "okay";
 198
 199         pll-data = <0x03000101 0x00000101 0x00001616>;
 200
 201         fixed-link {
 202                 speed = <1000>;
 203                 full-duplex;
 204         };
 205 };
 206
 207 &wmac {
 208         status = "okay";
 209
 210         mtd-cal-data = <&art 0x1000>;
 211 };