target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca956x.dtsi"
   7
   8 / {
   9         aliases {
  10                 led-boot = &led_power;
  11                 led-failsafe = &led_power;
  12                 led-running = &led_power;
  13                 led-upgrade = &led_power;
  14         };
  15
  16         leds: leds {
  17                 compatible = "gpio-leds";
  18
  19                 wps {
  20                         label = "elecom:red:wps";
  21                         gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
  22                 };
  23         };
  24
  25         keys {
  26                 compatible = "gpio-keys";
  27
  28                 reset {
  29                         label = "reset";
  30                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  31                         linux,code = <KEY_RESTART>;
  32                         debounce-interval = <60>;
  33                 };
  34
  35                 wps {
  36                         label = "wps";
  37                         gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
  38                         linux,code = <KEY_WPS_BUTTON>;
  39                         debounce-interval = <60>;
  40                 };
  41
  42                 ap {
  43                         label = "ap";
  44                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  45                         linux,code = <BTN_0>;
  46                         linux,input-type = <EV_SW>;
  47                         debounce-interval = <60>;
  48                 };
  49         };
  50 };
  51
  52 &spi {
  53         status = "okay";
  54         num-cs = <1>;
  55
  56         flash@0 {
  57                 compatible = "jedec,spi-nor";
  58                 reg = <0>;
  59                 spi-max-frequency = <25000000>;
  60
  61                 partitions: partitions {
  62                         compatible = "fixed-partitions";
  63                         #address-cells = <1>;
  64                         #size-cells = <1>;
  65
  66                         partition@0 {
  67                                 label = "u-boot";
  68                                 reg = <0x000000 0x040000>;
  69                                 read-only;
  70                         };
  71
  72                         partition@40000 {
  73                                 label = "u-boot-env";
  74                                 reg = <0x040000 0x010000>;
  75                                 read-only;
  76                         };
  77
  78                         partition@50000 {
  79                                 label = "nvram";
  80                                 reg = <0x050000 0x020000>;
  81                                 read-only;
  82                         };
  83                 };
  84         };
  85 };
  86
  87 &mdio0 {
  88         status = "okay";
  89
  90         phy0: ethernet-phy@0 {
  91                 reg = <0>;
  92
  93                 qca,ar8327-initvals = <
  94                         0x04 0x00000080 /* PORT0 PAD MODE CTRL */
  95                         0x50 0xcf37cf37 /* LED_CTRL0 */
  96                         0x54 0x00000000 /* LED_CTRL1 */
  97                         0x58 0x00000000 /* LED_CTRL2 */
  98                         0x5c 0x03ffff00 /* LED_CTRL3 */
  99                         0x7c 0x0000007e /* PORT0_STATUS */
 100                 >;
 101         };
 102 };
 103
 104 &eth0 {
 105         status = "okay";
 106
 107         pll-data = <0x03000101 0x00000101 0x00001919>;
 108
 109         mtd-mac-address = <&art 0x1002>;
 110         mtd-mac-address-increment = <(-1)>;
 111         phy-mode = "sgmii";
 112         phy-handle = <&phy0>;
 113 };
 114
 115 &uart {
 116         status = "okay";
 117 };
 118
 119 &wmac {
 120         status = "okay";
 121         mtd-cal-data = <&art 0x1000>;
 122 };