target/linux/ath79/dts/qca9563_phicomm_k2t.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "Phicomm K2T";
  11         compatible = "phicomm,k2t", "qca,qca9563";
  12
  13         aliases {
  14                 led-boot = &led_status_red;
  15                 led-failsafe = &led_status_red;
  16                 led-running = &led_status_red;
  17                 led-upgrade = &led_status_red;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 status_blue {
  24                         label = "phicomm:blue:status";
  25                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  26                 };
  27
  28                 led_status_red: status_red {
  29                         label = "phicomm:red:status";
  30                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  31                 };
  32
  33                 status_yellow {
  34                         label = "phicomm:yellow:status";
  35                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  36                 };
  37         };
  38
  39         keys {
  40                 compatible = "gpio-keys";
  41
  42                 reset {
  43                         linux,code = <KEY_RESTART>;
  44                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  45                         debounce-interval = <60>;
  46                 };
  47         };
  48 };
  49
  50 &uart {
  51         status = "okay";
  52 };
  53
  54 &gpio {
  55         status = "okay";
  56 };
  57
  58 &pcie {
  59         status = "okay";
  60 };
  61
  62 &spi {
  63         num-cs = <1>;
  64
  65         status = "okay";
  66
  67         flash@0 {
  68                 compatible = "jedec,spi-nor";
  69                 reg = <0>;
  70                 spi-max-frequency = <25000000>;
  71
  72                 partitions {
  73                         compatible = "fixed-partitions";
  74                         #address-cells = <1>;
  75                         #size-cells = <1>;
  76
  77                         partition@0 {
  78                                 label = "u-boot";
  79                                 reg = <0x000000 0x30000>;
  80                                 read-only;
  81                         };
  82
  83                         partition@30000 {
  84                                 label = "config";
  85                                 reg = <0x030000 0x10000>;
  86                                 read-only;
  87                         };
  88
  89                         partition@40000 {
  90                                 label = "permanent";
  91                                 reg = <0x040000 0x50000>;
  92                                 read-only;
  93                         };
  94
  95                         partition@90000 {
  96                                 compatible = "denx,uimage";
  97                                 label = "firmware";
  98                                 reg = <0x090000 0xf60000>;
  99                         };
 100
 101                         art: partition@ff0000 {
 102                                 label = "art";
 103                                 reg = <0xff0000 0x010000>;
 104                                 read-only;
 105                         };
 106                 };
 107         };
 108 };
 109
 110 &mdio0 {
 111         status = "okay";
 112
 113         phy-mask = <0>;
 114
 115         phy0: ethernet-phy@0 {
 116                 reg = <0>;
 117                 phy-mode = "sgmii";
 118
 119                 qca,ar8327-initvals = <
 120                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 121                         0x10 0x81000080 /* POWER_ON_STRIP */
 122                         0x50 0xcc35cc35 /* LED_CTRL0 */
 123                         0x54 0xcb37cb37 /* LED_CTRL1 */
 124                         0x58 0x00000000 /* LED_CTRL2 */
 125                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 126                         0x7c 0x0000007e /* PORT0_STATUS */
 127                         >;
 128         };
 129 };
 130
 131 &eth0 {
 132         status = "okay";
 133
 134         pll-data = <0x03000101 0x00000101 0x00001919>;
 135
 136         phy-mode = "sgmii";
 137         phy-handle = <&phy0>;
 138 };
 139
 140 &wmac {
 141         status = "okay";
 142         mtd-cal-data = <&art 0x1000>;
 143 };