target/linux/ath79/dts/qca9563_yuncore_xd4200.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca956x.dtsi"
   7
   8 / {
   9         aliases {
  10                 label-mac-device = &eth0;
  11         };
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 reset {
  21                         linux,code = <KEY_RESTART>;
  22                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  23                         debounce-interval = <60>;
  24                 };
  25         };
  26 };
  27
  28 &eth0 {
  29         status = "okay";
  30
  31         pll-data = <0x03000101 0x00000101 0x00001919>;
  32
  33         mtd-mac-address = <&art 0x0>;
  34         phy-mode = "sgmii";
  35         phy-handle = <&phy0>;
  36 };
  37
  38 &gpio {
  39         status = "okay";
  40 };
  41
  42 &mdio0 {
  43         status = "okay";
  44
  45         phy-mask = <0>;
  46
  47         phy0: ethernet-phy@0 {
  48                 reg = <0>;
  49                 phy-mode = "sgmii";
  50
  51                 qca,ar8327-initvals = <
  52                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
  53                         0x10 0x81000080 /* POWER_ON_STRIP */
  54                         0x50 0xcf37cf37 /* LED_CTRL0 */
  55                         0x54 0xcf37cf37 /* LED_CTRL1 */
  56                         0x58 0xcf37cf37 /* LED_CTRL2 */
  57                         0x5c 0x0000c300 /* LED_CTRL3 */
  58                         0x7c 0x0000007e /* PORT0_STATUS */
  59                 >;
  60         };
  61 };
  62
  63 &pcie {
  64         status = "okay";
  65
  66         wifi@0,0 {
  67                 compatible = "pci168c,0056";
  68                 reg = <0x0000 0 0 0 0>;
  69         };
  70 };
  71
  72 &spi {
  73         status = "okay";
  74
  75         num-cs = <1>;
  76
  77         flash@0 {
  78                 compatible = "jedec,spi-nor";
  79                 reg = <0>;
  80                 spi-max-frequency = <25000000>;
  81
  82                 partitions {
  83                         compatible = "fixed-partitions";
  84                         #address-cells = <1>;
  85                         #size-cells = <1>;
  86
  87                         partition@0 {
  88                                 label = "u-boot";
  89                                 reg = <0x000000 0x040000>;
  90                                 read-only;
  91                         };
  92
  93                         partition@40000 {
  94                                 label = "u-boot-env";
  95                                 reg = <0x040000 0x010000>;
  96                         };
  97
  98                         partition@50000 {
  99                                 compatible = "denx,uimage";
 100                                 label = "firmware";
 101                                 reg = <0x050000 0xfa0000>;
 102                         };
 103
 104                         art: partition@ff0000 {
 105                                 label = "art";
 106                                 reg = <0xff0000 0x010000>;
 107                                 read-only;
 108                         };
 109                 };
 110         };
 111 };
 112
 113 &uart {
 114         status = "okay";
 115 };
 116
 117 &wmac {
 118         status = "okay";
 119
 120         mtd-cal-data = <&art 0x1000>;
 121 };