+++ /dev/null
-/*
- * ADM5120 SoC definitions
- *
- * This file defines some constants specific to the ADM5120 SoC
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-#ifndef _ASM_MIPS_MACH_ADM5120_DEFS_H
-#define _ASM_MIPS_MACH_ADM5120_DEFS_H
-
-#define ADM5120_SDRAM0_BASE 0x00000000
-#define ADM5120_SDRAM1_BASE 0x01000000
-#define ADM5120_SRAM1_BASE 0x10000000
-#define ADM5120_EXTIO0_BASE 0x10C00000
-#define ADM5120_EXTIO0_SIZE 0x00200000
-#define ADM5120_EXTIO1_BASE 0x10E00000
-#define ADM5120_EXTIO1_SIZE 0x00200000
-#define ADM5120_MPMC_BASE 0x11000000
-#define ADM5120_MPMC_SIZE 0x00200000
-#define ADM5120_USBC_BASE 0x11200000
-#define ADM5120_USBC_SIZE 0x00200000
-#define ADM5120_PCIMEM_BASE 0x11400000
-#define ADM5120_PCIMEM_SIZE 0x00100000
-#define ADM5120_PCIIO_BASE 0x11500000
-#define ADM5120_PCIIO_SIZE 0x000FFFF0
-#define ADM5120_PCICFG_ADDR 0x115FFFF0
-#define ADM5120_PCICFG_DATA 0x115FFFF8
-#define ADM5120_PCICFG_SIZE 0x00000010
-#define ADM5120_SWITCH_BASE 0x12000000
-#define ADM5120_SWITCH_SIZE 0x00200000
-#define ADM5120_INTC_BASE 0x12200000
-#define ADM5120_INTC_SIZE 0x00200000
-#define ADM5120_UART0_BASE 0x12600000
-#define ADM5120_UART1_BASE 0x12800000
-#define ADM5120_UART_SIZE 0x00200000
-#define ADM5120_SRAM0_BASE 0x1FC00000
-
-#define ADM5120_NAND_BASE ADM5120_SRAM1_BASE
-#define ADM5120_NAND_SIZE 0xB
-
-#define ADM5120_CLK_175 175000000
-#define ADM5120_CLK_200 200000000
-#define ADM5120_CLK_225 225000000
-#define ADM5120_CLK_250 250000000
-
-#define ADM5120_UART_CLOCK 62500000
-
-#endif /* _ASM_MIPS_MACH_ADM5120_DEFS_H */
+++ /dev/null
-/*
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MACH_ADM5120_INFO_H
-#define _MACH_ADM5120_INFO_H
-
-#include <linux/types.h>
-
-extern unsigned int adm5120_prom_type;
-#define ADM5120_PROM_GENERIC 0
-#define ADM5120_PROM_CFE 1
-#define ADM5120_PROM_MYLOADER 2
-#define ADM5120_PROM_ROUTERBOOT 3
-#define ADM5120_PROM_BOOTBASE 4
-#define ADM5120_PROM_UBOOT 5
-#define ADM5120_PROM_LAST 5
-
-extern unsigned int adm5120_product_code;
-extern unsigned int adm5120_revision;
-extern unsigned int adm5120_nand_boot;
-
-extern unsigned long adm5120_speed;
-#define ADM5120_SPEED_175 175000000
-#define ADM5120_SPEED_200 200000000
-#define ADM5120_SPEED_225 225000000
-#define ADM5120_SPEED_250 250000000
-
-extern unsigned int adm5120_package;
-#define ADM5120_PACKAGE_PQFP 0
-#define ADM5120_PACKAGE_BGA 1
-
-extern unsigned long adm5120_memsize;
-
-extern unsigned long adm5120_mach_type;
-
-#define MACH_ADM5120_GENERIC 0 /* Generic board */
-#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */
-#define MACH_ADM5120_WP54 2 /* Compex WP54G/WP54AG/WPP54G/WPP54AG */
-#define MACH_ADM5120_NP28G 3 /* Compex NP28G */
-#define MACH_ADM5120_NP28GHS 4 /* Compex NP28G HotSpot */
-#define MACH_ADM5120_NP27G 5 /* Compex NP27G */
-#define MACH_ADM5120_WP54Gv1C 6 /* Compex WP54G version 1C */
-#define MACH_ADM5120_RB_11X 7 /* Mikrotik RouterBOARD 111/112 */
-#define MACH_ADM5120_RB_133 8 /* Mikrotik RouterBOARD 133 */
-#define MACH_ADM5120_RB_133C 9 /* Mikrotik RouterBOARD 133c */
-#define MACH_ADM5120_RB_150 10 /* Mikrotik RouterBOARD 150 */
-#define MACH_ADM5120_RB_153 11 /* Mikrotik RouterBOARD 153 */
-#define MACH_ADM5120_RB_192 12 /* Mikrotik RouterBOARD 192 */
-#define MACH_ADM5120_HS100 13 /* ZyXEL HomeSafe 100/100W */
-#define MACH_ADM5120_P334U 14 /* ZyXEL Prestige 334U */
-#define MACH_ADM5120_P334W 15 /* ZyXEL Prestige 334W */
-#define MACH_ADM5120_P334WH 16 /* ZyXEL Prestige 334WH */
-#define MACH_ADM5120_P334WHD 17 /* ZyXEL Prestige 334WHD */
-#define MACH_ADM5120_P334WT 18 /* ZyXEL Prestige 334WT */
-#define MACH_ADM5120_P335 19 /* ZyXEL Prestige 335/335WT */
-#define MACH_ADM5120_P335PLUS 20 /* ZyXEL Prestige 335Plus */
-#define MACH_ADM5120_P335U 21 /* ZyXEL Prestige 335U */
-#define MACH_ADM5120_ES2108 22 /* ZyXEL Ethernet Switch 2108 */
-#define MACH_ADM5120_ES2108F 23 /* ZyXEL Ethernet Switch 2108-F */
-#define MACH_ADM5120_ES2108G 24 /* ZyXEL Ethernet Switch 2108-G */
-#define MACH_ADM5120_ES2108LC 25 /* ZyXEL Ethernet Switch 2108-LC */
-#define MACH_ADM5120_ES2108PWR 26 /* ZyXEL Ethernet Switch 2108-PWR */
-#define MACH_ADM5120_ES2024A 27 /* ZyXEL Ethernet Switch 2024A */
-#define MACH_ADM5120_ES2024PWR 28 /* ZyXEL Ethernet Switch 2024PWR */
-#define MACH_ADM5120_CAS630 29 /* Cellvision CAS-630/630W */
-#define MACH_ADM5120_CAS670 30 /* Cellvision CAS-670/670W */
-#define MACH_ADM5120_CAS700 31 /* Cellvision CAS-700/700W */
-#define MACH_ADM5120_CAS771 32 /* Cellvision CAS-771/771W */
-#define MACH_ADM5120_CAS790 33 /* Cellvision CAS-790 */
-#define MACH_ADM5120_CAS861 34 /* Cellvision CAS-861/861W */
-#define MACH_ADM5120_NFS101U 35 /* Cellvision NFS-101U/101WU */
-#define MACH_ADM5120_NFS202U 36 /* Cellvision NFS-202U/202WU */
-#define MACH_ADM5120_EASY5120PATA 37 /* Infineon EASY 5120P-ATA */
-#define MACH_ADM5120_EASY5120RT 38 /* Infineon EASY 5120-RT */
-#define MACH_ADM5120_EASY5120WVOIP 39 /* Infineon EASY 5120-WVoIP */
-#define MACH_ADM5120_EASY83000 40 /* Infineon EASY-83000 */
-#define MACH_ADM5120_BR6104K 41 /* Edimax BR-6104K */
-#define MACH_ADM5120_BR6104KP 42 /* Edimax BR-6104KP */
-#define MACH_ADM5120_BR61X4WG 43 /* Edimax BR-6104Wg/BR-6114WG */
-#define MACH_ADM5120_PMUGW 44 /* Motorola Powerline MU Gateway */
-
-/*
- * TODO:remove adm5120_eth* variables when the switch driver will be
- * converted into a real platform driver
- */
-extern unsigned int adm5120_eth_num_ports;
-extern unsigned char adm5120_eth_macs[6][6];
-extern unsigned char adm5120_eth_vlans[6];
-
-extern void adm5120_soc_init(void) __init;
-extern void adm5120_mem_init(void) __init;
-extern void adm5120_ndelay(u32 ns);
-
-extern void (*adm5120_board_reset)(void);
-
-extern void adm5120_gpio_init(void) __init;
-extern void adm5120_gpio_csx0_enable(void) __init;
-extern void adm5120_gpio_csx1_enable(void) __init;
-extern void adm5120_gpio_ew_enable(void) __init;
-
-static inline int adm5120_package_pqfp(void)
-{
- return (adm5120_package == ADM5120_PACKAGE_PQFP);
-}
-
-static inline int adm5120_package_bga(void)
-{
- return (adm5120_package == ADM5120_PACKAGE_BGA);
-}
-
-static inline int adm5120_has_pci(void)
-{
- return (adm5120_package == ADM5120_PACKAGE_BGA);
-}
-
-static inline int adm5120_has_gmii(void)
-{
- return (adm5120_package == ADM5120_PACKAGE_BGA);
-}
-
-#endif /* _MACH_ADM5120_INFO_H */
+++ /dev/null
-/*
- * ADM5120 interrupt controller definitions
- *
- * This header file defines the hardware registers of the ADM5120 SoC
- * built-in interrupt controller.
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MACH_ADM5120_INTC_H
-#define _MACH_ADM5120_INTC_H
-
-/*
- * INTC register offsets
- */
-#define INTC_REG_IRQ_STATUS 0x00 /* Interrupt status after masking */
-#define INTC_REG_IRQ_RAW_STATUS 0x04 /* Interrupt status before masking */
-#define INTC_REG_IRQ_ENABLE 0x08 /* Used to enable the interrupt sources */
-#define INTC_REG_IRQ_ENABLE_CLEAR 0x0C /* Used to disable the interrupt sources */
-#define INTC_REG_IRQ_DISABLE INTC_REG_IRQ_ENABLE_CLEAR
-#define INTC_REG_INT_MODE 0x14 /* The interrupt mode of the sources */
-#define INTC_REG_FIQ_STATUS 0x18 /* FIQ status */
-#define INTC_REG_IRQ_TEST_SOURCE 0x1C
-#define INTC_REG_IRQ_SOURCE_SELECT 0x20
-#define INTC_REG_INT_LEVEL 0x24
-
-/*
- * INTC IRQ numbers
- */
-#define INTC_IRQ_TIMER 0 /* built in timer */
-#define INTC_IRQ_UART0 1 /* built-in UART0 */
-#define INTC_IRQ_UART1 2 /* built-in UART1 */
-#define INTC_IRQ_USBC 3 /* USB Host Controller */
-#define INTC_IRQ_GPIO2 4 /* GPIO line 2 */
-#define INTC_IRQ_GPIO4 5 /* GPIO line 4 */
-#define INTC_IRQ_PCI0 6 /* PCI slot 2 */
-#define INTC_IRQ_PCI1 7 /* PCI slot 3 */
-#define INTC_IRQ_PCI2 8 /* PCI slot 4 */
-#define INTC_IRQ_SWITCH 9 /* built-in ethernet switch */
-#define INTC_IRQ_LAST INTC_IRQ_SWITCH
-#define INTC_IRQ_COUNT 10
-
-/*
- * INTC register bits
- */
-#define INTC_INT_TIMER ( 1 << INTC_IRQ_TIMER )
-#define INTC_INT_UART0 ( 1 << INTC_IRQ_UART0 )
-#define INTC_INT_UART1 ( 1 << INTC_IRQ_UART1 )
-#define INTC_INT_USBC ( 1 << INTC_IRQ_USBC )
-#define INTC_INT_INTX0 ( 1 << INTC_IRQ_INTX0 )
-#define INTC_INT_INTX1 ( 1 << INTC_IRQ_INTX1 )
-#define INTC_INT_PCI0 ( 1 << INTC_IRQ_PCI0 )
-#define INTC_INT_PCI1 ( 1 << INTC_IRQ_PCI1 )
-#define INTC_INT_PCI2 ( 1 << INTC_IRQ_PCI2 )
-#define INTC_INT_SWITCH ( 1 << INTC_IRQ_SWITCH )
-#define INTC_INT_ALL (( 1 << INTC_IRQ_COUNT)-1)
-
-#endif /* _MACH_ADM5120_INTC_H */
+++ /dev/null
-/*
- * ADM5120 MPMC (Multiport Memory Controller) register definitions
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MACH_ADM5120_MPMC_H
-#define _MACH_ADM5120_MPMC_H
-
-#define MPMC_READ_REG(r) __raw_readl( \
- (void __iomem *)KSEG1ADDR(ADM5120_MPMC_BASE) + MPMC_REG_ ## r)
-#define MPMC_WRITE_REG(r, v) __raw_writel((v), \
- (void __iomem *)KSEG1ADDR(ADM5120_MPMC_BASE) + MPMC_REG_ ## r)
-
-#define MPMC_REG_CTRL 0x0000
-#define MPMC_REG_STATUS 0x0004
-#define MPMC_REG_CONF 0x0008
-#define MPMC_REG_DC 0x0020
-#define MPMC_REG_DR 0x0024
-#define MPMC_REG_DRP 0x0030
-
-#define MPMC_REG_DC0 0x0100
-#define MPMC_REG_DRC0 0x0104
-#define MPMC_REG_DC1 0x0120
-#define MPMC_REG_DRC1 0x0124
-#define MPMC_REG_DC2 0x0140
-#define MPMC_REG_DRC2 0x0144
-#define MPMC_REG_DC3 0x0160
-#define MPMC_REG_DRC3 0x0164
-#define MPMC_REG_SC0 0x0200 /* for F_CS1_N */
-#define MPMC_REG_SC1 0x0220 /* for F_CS0_N */
-#define MPMC_REG_SC2 0x0240
-#define MPMC_REG_WEN2 0x0244
-#define MPMC_REG_OEN2 0x0248
-#define MPMC_REG_RD2 0x024C
-#define MPMC_REG_PG2 0x0250
-#define MPMC_REG_WR2 0x0254
-#define MPMC_REG_TN2 0x0258
-#define MPMC_REG_SC3 0x0260
-
-/* Control register bits */
-#define MPMC_CTRL_AM ( 1 << 1 ) /* Address Mirror */
-#define MPMC_CTRL_LPM ( 1 << 2 ) /* Low Power Mode */
-#define MPMC_CTRL_DWB ( 1 << 3 ) /* Drain Write Buffers */
-
-/* Status register bits */
-#define MPMC_STATUS_BUSY ( 1 << 0 ) /* Busy */
-#define MPMC_STATUS_WBS ( 1 << 1 ) /* Write Buffer Status */
-#define MPMC_STATUS_SRA ( 1 << 2 ) /* Self-Refresh Acknowledge*/
-
-/* Dynamic Control register bits */
-#define MPMC_DC_CE ( 1 << 0 )
-#define MPMC_DC_DMC ( 1 << 1 )
-#define MPMC_DC_SRR ( 1 << 2 )
-#define MPMC_DC_SI_SHIFT 7
-#define MPMC_DC_SI_MASK ( 3 << 7 )
-#define MPMC_DC_SI_NORMAL ( 0 << 7 )
-#define MPMC_DC_SI_MODE ( 1 << 7 )
-#define MPMC_DC_SI_PALL ( 2 << 7 )
-#define MPMC_DC_SI_NOP ( 3 << 7 )
-
-#define SRAM_REG_CONF 0x00
-#define SRAM_REG_WWE 0x04
-#define SRAM_REG_WOE 0x08
-#define SRAM_REG_WRD 0x0C
-#define SRAM_REG_WPG 0x10
-#define SRAM_REG_WWR 0x14
-#define SRAM_REG_WTR 0x18
-
-/* Dynamic Configuration register bits */
-#define DC_BE (1 << 19) /* buffer enable */
-#define DC_RW_SHIFT 28 /* shift for number of rows */
-#define DC_RW_MASK 0x03
-#define DC_NB_SHIFT 26 /* shift for number of banks */
-#define DC_NB_MASK 0x01
-#define DC_CW_SHIFT 22 /* shift for number of columns */
-#define DC_CW_MASK 0x07
-#define DC_DW_SHIFT 7 /* shift for device width */
-#define DC_DW_MASK 0x03
-
-/* Static Configuration register bits */
-#define SC_MW_MASK 0x03 /* memory width mask */
-#define SC_MW_8 0x00 /* 8 bit memory width */
-#define SC_MW_16 0x01 /* 16 bit memory width */
-#define SC_MW_32 0x02 /* 32 bit memory width */
-
-#endif /* _MACH_ADM5120_MPMC_H */
+++ /dev/null
-/*
- * ADM5120 NAND interface definitions
- *
- * This header file defines the hardware registers of the ADM5120 SoC
- * built-in NAND interface.
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * NAND interface routines was based on a driver for Linux 2.6.19+ which
- * was derived from the driver for Linux 2.4.xx published by Mikrotik for
- * their RouterBoard 1xx and 5xx series boards.
- * Copyright (C) 2007 David Goodenough <david.goodenough@linkchoose.co.uk>
- * Copyright (C) 2007 Florian Fainelli <florian@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MACH_ADM5120_NAND_H
-#define _MACH_ADM5120_NAND_H
-
-#include <linux/types.h>
-#include <linux/io.h>
-
-#include <asm/mach-adm5120/adm5120_defs.h>
-#include <asm/mach-adm5120/adm5120_switch.h>
-
-/* NAND control registers */
-#define NAND_REG_DATA 0x0 /* data register */
-#define NAND_REG_SET_CEn 0x1 /* CE# low */
-#define NAND_REG_CLR_CEn 0x2 /* CE# high */
-#define NAND_REG_CLR_CLE 0x3 /* CLE low */
-#define NAND_REG_SET_CLE 0x4 /* CLE high */
-#define NAND_REG_CLR_ALE 0x5 /* ALE low */
-#define NAND_REG_SET_ALE 0x6 /* ALE high */
-#define NAND_REG_SET_SPn 0x7 /* SP# low (use spare area) */
-#define NAND_REG_CLR_SPn 0x8 /* SP# high (do not use spare area) */
-#define NAND_REG_SET_WPn 0x9 /* WP# low */
-#define NAND_REG_CLR_WPn 0xA /* WP# high */
-#define NAND_REG_STATUS 0xB /* Status register */
-
-#define ADM5120_NAND_STATUS_READY 0x80
-
-#define NAND_READ_REG(r) \
- readb((void __iomem *)KSEG1ADDR(ADM5120_NAND_BASE) + (r))
-#define NAND_WRITE_REG(r, v) \
- writeb((v),(void __iomem *)KSEG1ADDR(ADM5120_NAND_BASE) + (r))
-
-/*-------------------------------------------------------------------------*/
-
-static inline void adm5120_nand_enable(void)
-{
- SW_WRITE_REG(SWITCH_REG_BW_CNTL1, BW_CNTL1_NAND_ENABLE);
- SW_WRITE_REG(SWITCH_REG_BOOT_DONE, 1);
-}
-
-static inline void adm5120_nand_set_wpn(unsigned int set)
-{
- NAND_WRITE_REG((set) ? NAND_REG_SET_WPn : NAND_REG_CLR_WPn, 1);
-}
-
-static inline void adm5120_nand_set_spn(unsigned int set)
-{
- NAND_WRITE_REG((set) ? NAND_REG_SET_SPn : NAND_REG_CLR_SPn, 1);
-}
-
-static inline void adm5120_nand_set_cle(unsigned int set)
-{
- NAND_WRITE_REG((set) ? NAND_REG_SET_CLE : NAND_REG_CLR_CLE, 1);
-}
-
-static inline void adm5120_nand_set_ale(unsigned int set)
-{
- NAND_WRITE_REG((set) ? NAND_REG_SET_ALE : NAND_REG_CLR_ALE, 1);
-}
-
-static inline void adm5120_nand_set_cen(unsigned int set)
-{
- NAND_WRITE_REG((set) ? NAND_REG_SET_CEn : NAND_REG_CLR_CEn, 1);
-}
-
-static inline u8 adm5120_nand_get_status(void)
-{
- return NAND_READ_REG(NAND_REG_STATUS);
-}
-
-#endif /* _MACH_ADM5120_NAND_H */
+++ /dev/null
-/*
- * ADM5120 specific platform definitions
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _ASM_MIPS_MACH_ADM5120_PLATFORM_H
-#define _ASM_MIPS_MACH_ADM5120_PLATFORM_H
-
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/leds.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/gpio_buttons.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/serial.h>
-
-struct adm5120_flash_platform_data {
- void (*set_vpp)(struct map_info *, int);
- void (*switch_bank)(unsigned);
- u32 window_size;
-#ifdef CONFIG_MTD_PARTITIONS
- unsigned int nr_parts;
- struct mtd_partition *parts;
-#endif
-};
-
-struct adm5120_switch_platform_data {
- /* TODO: not yet implemented */
-};
-
-struct adm5120_pci_irq {
- u8 slot;
- u8 func;
- u8 pin;
- unsigned irq;
-};
-
-#define PCIIRQ(s,f,p,i) {.slot = (s), .func = (f), .pin = (p), .irq = (i)}
-
-#ifdef CONFIG_PCI
-extern void adm5120_pci_set_irq_map(unsigned int nr_irqs,
- struct adm5120_pci_irq *map) __init;
-#else
-static inline void adm5120_pci_set_irq_map(unsigned int nr_irqs,
- struct adm5120_pci_irq *map)
-{
-}
-#endif
-
-extern void adm5120_setup_eth_macs(u8 *mac_base) __init;
-
-extern struct adm5120_flash_platform_data adm5120_flash0_data;
-extern struct adm5120_flash_platform_data adm5120_flash1_data;
-
-extern void adm5120_add_device_flash(unsigned id) __init;
-extern void adm5120_add_device_usb(void) __init;
-extern void adm5120_add_device_uart(unsigned id) __init;
-extern void adm5120_add_device_nand(struct platform_nand_data *pdata) __init;
-extern void adm5120_add_device_switch(unsigned num_ports, u8 *vlan_map) __init;
-extern void adm5120_add_device_gpio(u32 disable_mask) __init;
-extern void adm5120_add_device_gpio_buttons(unsigned nbuttons,
- struct gpio_button *buttons) __init;
-
-#define GPIO_LED_DEF(g, n, t, a) { \
- .name = (n), \
- .default_trigger = (t), \
- .gpio = (g), \
- .active_low = (a) \
-}
-
-#define GPIO_LED_STD(g, n, t) GPIO_LED_DEF((g), (n), (t), 0)
-#define GPIO_LED_INV(g, n, t) GPIO_LED_DEF((g), (n), (t), 1)
-
-extern void adm5120_add_device_gpio_leds(unsigned num_leds,
- struct gpio_led *leds) __init;
-
-#endif /* _ASM_MIPS_MACH_ADM5120_PLATFORM_H */
+++ /dev/null
-/*
- * ADM5120 ethernet switch definitions
- *
- * This header file defines the hardware registers of the ADM5120 SoC
- * built-in Ethernet switch.
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MACH_ADM5120_SWITCH_H
-#define _MACH_ADM5120_SWITCH_H
-
-#ifndef BIT
-# define BIT(at) (1 << (at))
-#endif
-#define BITMASK(len) (BIT(len)-1)
-
-#define SW_READ_REG(r) __raw_readl( \
- (void __iomem *)KSEG1ADDR(ADM5120_SWITCH_BASE) + r)
-#define SW_WRITE_REG(r, v) __raw_writel((v), \
- (void __iomem *)KSEG1ADDR(ADM5120_SWITCH_BASE) + r)
-
-/* Switch register offsets */
-#define SWITCH_REG_CODE 0x0000
-#define SWITCH_REG_SOFT_RESET 0x0004 /* Soft Reset */
-#define SWITCH_REG_BOOT_DONE 0x0008 /* Boot Done */
-#define SWITCH_REG_SW_RESET 0x000C /* Switch Reset */
-#define SWITCH_REG_PHY_STATUS 0x0014 /* PHY Status */
-#define SWITCH_REG_MEMCTRL 0x001C /* Memory Control */
-#define SWITCH_REG_CPUP_CONF 0x0024 /* CPU Port Configuration */
-#define SWITCH_REG_PORT_CONF0 0x0028 /* Port Configuration 0 */
-#define SWITCH_REG_PORT_CONF1 0x002C /* Port Configuration 1 */
-#define SWITCH_REG_PORT_CONF2 0x0030 /* Port Configuration 2 */
-#define SWITCH_REG_VLAN_G1 0x0040 /* VLAN group 1 */
-#define SWITCH_REG_VLAN_G2 0x0044 /* VLAN group 2 */
-#define SWITCH_REG_SEND_TRIG 0x0048 /* Send Trigger */
-#define SWITCH_REG_MAC_WT0 0x0058 /* MAC Write Address 0 */
-#define SWITCH_REG_MAC_WT1 0x005C /* MAC Write Address 1 */
-#define SWITCH_REG_BW_CNTL0 0x0060 /* Bandwidth Control 0 */
-#define SWITCH_REG_BW_CNTL1 0x0064 /* Bandwidth Control 1 */
-#define SWITCH_REG_PHY_CNTL0 0x0068 /* PHY Control 0 */
-#define SWITCH_REG_PHY_CNTL1 0x006C /* PHY Control 1 */
-#define SWITCH_REG_PORT_TH 0x0078 /* Port Threshold */
-#define SWITCH_REG_PHY_CNTL2 0x007C /* PHY Control 2 */
-#define SWITCH_REG_PHY_CNTL3 0x0080 /* PHY Control 3 */
-#define SWITCH_REG_PRI_CNTL 0x0084 /* Priority Control */
-#define SWITCH_REG_PHY_CNTL4 0x00A0 /* PHY Control 4 */
-#define SWITCH_REG_EMPTY_CNT 0x00A4 /* Empty Count */
-#define SWITCH_REG_PORT_CNTLS 0x00A8 /* Port Control Select */
-#define SWITCH_REG_PORT_CNTL 0x00AC /* Port Control */
-#define SWITCH_REG_INT_STATUS 0x00B0 /* Interrupt Status */
-#define SWITCH_REG_INT_MASK 0x00B4 /* Interrupt Mask */
-#define SWITCH_REG_GPIO_CONF0 0x00B8 /* GPIO Configuration 0 */
-#define SWITCH_REG_GPIO_CONF2 0x00BC /* GPIO Configuration 1 */
-#define SWITCH_REG_WDOG0 0x00C0 /* Watchdog 0 */
-#define SWITCH_REG_WDOG1 0x00C4 /* Watchdog 1 */
-
-#define SWITCH_REG_SHDA 0x00D0 /* Send High Descriptors Address */
-#define SWITCH_REG_SLDA 0x00D4 /* Send Low Descriptors Address */
-#define SWITCH_REG_RHDA 0x00D8 /* Receive High Descriptor Address */
-#define SWITCH_REG_RLDA 0x00DC /* Receive Low Descriptor Address */
-#define SWITCH_REG_SHWA 0x00E0 /* Send High Working Address */
-#define SWITCH_REG_SLWA 0x00E4 /* Send Low Working Address */
-#define SWITCH_REG_RHWA 0x00E8 /* Receive High Working Address */
-#define SWITCH_REG_RLWA 0x00EC /* Receive Low Working Address */
-
-#define SWITCH_REG_TIMER_INT 0x00F0 /* Timer */
-#define SWITCH_REG_TIMER 0x00F4 /* Timer Interrupt */
-
-#define SWITCH_REG_PORT0_LED 0x0100
-#define SWITCH_REG_PORT1_LED 0x0104
-#define SWITCH_REG_PORT2_LED 0x0108
-#define SWITCH_REG_PORT3_LED 0x010C
-#define SWITCH_REG_PORT4_LED 0x0110
-
-/* CODE register bits */
-#define CODE_PC_MASK BITMASK(16) /* Product Code */
-#define CODE_REV_SHIFT 16
-#define CODE_REV_MASK BITMASK(4) /* Product Revision */
-#define CODE_CLKS_SHIFT 20
-#define CODE_CLKS_MASK BITMASK(2) /* Clock Speed */
-#define CODE_CLKS_175 0 /* 175 MHz */
-#define CODE_CLKS_200 1 /* 200 MHz */
-#define CODE_CLKS_225 2 /* 225 MHz */
-#define CODE_CLKS_250 3 /* 250 MHz */
-#define CODE_NAB BIT(24) /* NAND boot */
-#define CODE_PK_MASK BITMASK(1) /* Package type */
-#define CODE_PK_SHIFT 29
-#define CODE_PK_BGA 0 /* BGA package */
-#define CODE_PK_PQFP 1 /* PQFP package */
-
-/* MEMCTRL register bits */
-#define MEMCTRL_SDRS_MASK BITMASK(3) /* SDRAM bank size */
-#define MEMCTRL_SDRS_4M 0x01
-#define MEMCTRL_SDRS_8M 0x02
-#define MEMCTRL_SDRS_16M 0x03
-#define MEMCTRL_SDRS_64M 0x04
-#define MEMCTRL_SDRS_128M 0x05
-#define MEMCTRL_SDR1_ENABLE BIT(5) /* enable SDRAM bank 1 */
-
-#define MEMCTRL_SRS0_SHIFT 8 /* shift for SRAM0 size */
-#define MEMCTRL_SRS1_SHIFT 16 /* shift for SRAM1 size */
-#define MEMCTRL_SRS_MASK BITMASK(3) /* SRAM size mask */
-#define MEMCTRL_SRS_DISABLED 0x00 /* Disabled */
-#define MEMCTRL_SRS_512K 0x01 /* 512KB*/
-#define MEMCTRL_SRS_1M 0x02 /* 1MB */
-#define MEMCTRL_SRS_2M 0x03 /* 2MB */
-#define MEMCTRL_SRS_4M 0x04 /* 4MB */
-
-/* Port bits used in various registers */
-#define SWITCH_PORT_PHY0 BIT(0)
-#define SWITCH_PORT_PHY1 BIT(1)
-#define SWITCH_PORT_PHY2 BIT(2)
-#define SWITCH_PORT_PHY3 BIT(3)
-#define SWITCH_PORT_PHY4 BIT(4)
-#define SWITCH_PORT_MII BIT(5)
-#define SWITCH_PORT_CPU BIT(6)
-
-/* Port bit shorthands */
-#define SWITCH_PORTS_PHY 0x1F /* phy ports */
-#define SWITCH_PORTS_NOCPU 0x3F /* physical ports */
-#define SWITCH_PORTS_ALL 0x7F /* all ports */
-
-/* CPUP_CONF register bits */
-#define CPUP_CONF_DCPUP BIT(0) /* Disable CPU port */
-#define CPUP_CONF_CRCP BIT(1) /* CRC padding from CPU */
-#define CPUP_CONF_BTM BIT(2) /* Bridge Testing Mode */
-#define CPUP_CONF_DUNP_SHIFT 9 /* Disable Unknown Packets for portX */
-#define CPUP_CONF_DMCP_SHIFT 16 /* Disable Mcast Packets form portX */
-#define CPUP_CONF_DBCP_SHIFT 24 /* Disable Bcast Packets form portX */
-
-/* PORT_CONF0 register bits */
-#define PORT_CONF0_DP_SHIFT 0 /* Disable Port */
-#define PORT_CONF0_EMCP_SHIFT 8 /* Enable All MC Packets */
-#define PORT_CONF0_BP_SHIFT 16 /* Enable Back Pressure */
-
-/* PORT_CONF1 register bits */
-#define PORT_CONF1_DISL_SHIFT 0 /* Disable Learning */
-#define PORT_CONF1_BS_SHIFT 6 /* Blocking State */
-#define PORT_CONF1_BM_SHIFT 12 /* Blocking Mode */
-
-/* SEND_TRIG register bits */
-#define SEND_TRIG_STL BIT(0) /* Send Trigger Low */
-#define SEND_TRIG_STH BIT(1) /* Send Trigger High */
-
-/* MAC_WT0 register bits */
-#define MAC_WT0_MAWC BIT(0) /* MAC address write command */
-#define MAC_WT0_MWD_SHIFT 1
-#define MAC_WT0_MWD BIT(1) /* MAC write done */
-#define MAC_WT0_WFB BIT(2) /* Write Filter Bit */
-#define MAC_WT0_WVN_SHIFT 3 /* Write Vlan Number shift */
-#define MAC_WT0_WVE BIT(6) /* Write VLAN enable */
-#define MAC_WT0_WPMN_SHIFT 7
-#define MAC_WT0_WAF_SHIFT 13 /* Write Age Field shift */
-#define MAC_WT0_WAF_EMPTY 0
-#define MAC_WT0_WAF_STATIC 7 /* age: static */
-#define MAC_WT0_MAC0_SHIFT 16
-#define MAC_WT0_MAC1_SHIFT 24
-
-/* MAC_WT1 register bits */
-#define MAC_WT1_MAC2_SHIFT 0
-#define MAC_WT1_MAC3_SHIFT 8
-#define MAC_WT1_MAC4_SHIFT 16
-#define MAC_WT1_MAC5_SHIFT 24
-
-/* BW_CNTL0/BW_CNTL1 register bits */
-#define BW_CNTL_DISABLE 0x00
-#define BW_CNTL_64K 0x01
-#define BW_CNTL_128K 0x02
-#define BW_CNTL_256K 0x03
-#define BW_CNTL_512K 0x04
-#define BW_CNTL_1M 0x05
-#define BW_CNTL_4M 0x06
-#define BW_CNTL_10M 0x07
-
-#define P4TBC_SHIFT 0
-#define P4RBC_SHIFT 4
-#define P5TBC_SHIFT 8
-#define P5RBC_SHIFT 12
-
-#define BW_CNTL1_NAND_ENABLE 0x100
-
-/* PHY_CNTL0 register bits */
-#define PHY_CNTL0_PHYA_MASK BITMASK(5)
-#define PHY_CNTL0_PHYR_MASK BITMASK(5)
-#define PHY_CNTL0_PHYR_SHIFT 8
-#define PHY_CNTL0_WC BIT(13) /* Write Command */
-#define PHY_CNTL0_RC BIT(14) /* Read Command */
-#define PHY_CNTL0_WTD_MASK BIT(16) /* Read Command */
-#define PHY_CNTL0_WTD_SHIFT 16
-
-/* PHY_CNTL1 register bits */
-#define PHY_CNTL1_WOD BIT(0) /* Write Operation Done */
-#define PHY_CNTL1_ROD BIT(1) /* Read Operation Done */
-#define PHY_CNTL1_RD_MASK BITMASK(16)
-#define PHY_CNTL1_RD_SHIFT 16
-
-/* PHY_CNTL2 register bits */
-#define PHY_CNTL2_ANE_SHIFT 0 /* Auto Negotiation Enable */
-#define PHY_CNTL2_SC_SHIFT 5 /* Speed Control */
-#define PHY_CNTL2_DC_SHIFT 10 /* Duplex Control */
-#define PHY_CNTL2_FNCV_SHIFT 15 /* Recommended FC Value */
-#define PHY_CNTL2_PHYR_SHIFT 20 /* PHY reset */
-#define PHY_CNTL2_AMDIX_SHIFT 25 /* Auto MDIX enable */
-/* PHY_CNTL2_RMAE is bad in datasheet */
-#define PHY_CNTL2_RMAE BIT(31) /* Recommended MCC Average enable */
-
-/* PHY_CNTL3 register bits */
-#define PHY_CNTL3_RNT BIT(10) /* Recommend Normal Threshold */
-
-/* PORT_TH register bits */
-#define PORT_TH_PPT_MASK BITMASK(8) /* Per Port Threshold */
-#define PORT_TH_CPUT_SHIFT 8 /* CPU Port Buffer Threshold */
-#define PORT_TH_CPUT_MASK BITMASK(8)
-#define PORT_TH_CPUHT_SHIFT 16 /* CPU Hold Threshold */
-#define PORT_TH_CPUHT_MASK BITMASK(8)
-#define PORT_TH_CPURT_SHIFT 24 /* CPU Release Threshold */
-#define PORT_TH_CPURT_MASK BITMASK(8)
-
-/* EMPTY_CNT register bits */
-#define EMPTY_CNT_EBGB_MASK BITMASK(9) /* Empty Blocks in the Global Buffer */
-
-/* GPIO_CONF0 register bits */
-#define GPIO_CONF0_MASK BITMASK(8)
-#define GPIO_CONF0_IM_SHIFT 0
-#define GPIO_CONF0_IV_SHIFT 8
-#define GPIO_CONF0_OE_SHIFT 16
-#define GPIO_CONF0_OV_SHIFT 24
-#define GPIO_CONF0_IM_MASK (0xFF << GPIO_CONF0_IM_SHIFT)
-#define GPIO_CONF0_IV_MASK (0xFF << GPIO_CONF0_IV_SHIFT)
-#define GPIO_CONF0_OE_MASK (0xFF << GPIO_CONF0_OE_SHIFT)
-#define GPIO_CONF0_OV_MASK (0xFF << GPIO_CONF0_OV_SHIFT)
-
-/* GPIO_CONF2 register bits */
-#define GPIO_CONF2_CSX0 BIT(4) /* enable CSX0:INTX0 on GPIO 1:2 */
-#define GPIO_CONF2_CSX1 BIT(5) /* enable CSX1:INTX1 on GPIO 3:4 */
-#define GPIO_CONF2_EW BIT(6) /* enable wait state pin for CSX0/1 */
-
-/* INT_STATUS/INT_MASK register bits */
-#define SWITCH_INT_SHD BIT(0) /* Send High Done */
-#define SWITCH_INT_SLD BIT(1) /* Send Low Done */
-#define SWITCH_INT_RHD BIT(2) /* Receive High Done */
-#define SWITCH_INT_RLD BIT(3) /* Receive Low Done */
-#define SWITCH_INT_HDF BIT(4) /* High Descriptor Full */
-#define SWITCH_INT_LDF BIT(5) /* Low Descriptor Full */
-#define SWITCH_INT_P0QF BIT(6) /* Port0 Queue Full */
-#define SWITCH_INT_P1QF BIT(7) /* Port1 Queue Full */
-#define SWITCH_INT_P2QF BIT(8) /* Port2 Queue Full */
-#define SWITCH_INT_P3QF BIT(9) /* Port3 Queue Full */
-#define SWITCH_INT_P4QF BIT(10) /* Port4 Queue Full */
-#define SWITCH_INT_P5QF BIT(11) /* Port5 Queue Full */
-#define SWITCH_INT_CPQF BIT(13) /* CPU Queue Full */
-#define SWITCH_INT_GQF BIT(14) /* Global Queue Full */
-#define SWITCH_INT_MD BIT(15) /* Must Drop */
-#define SWITCH_INT_BCS BIT(16) /* BC Storm */
-#define SWITCH_INT_PSC BIT(18) /* Port Status Change */
-#define SWITCH_INT_ID BIT(19) /* Intruder Detected */
-#define SWITCH_INT_W0TE BIT(20) /* Watchdog 0 Timer Expired */
-#define SWITCH_INT_W1TE BIT(21) /* Watchdog 1 Timer Expired */
-#define SWITCH_INT_RDE BIT(22) /* Receive Descriptor Error */
-#define SWITCH_INT_SDE BIT(23) /* Send Descriptor Error */
-#define SWITCH_INT_CPUH BIT(24) /* CPU Hold */
-
-/* TIMER_INT register bits */
-#define TIMER_INT_TOS BIT(0) /* time-out status */
-#define TIMER_INT_TOM BIT(16) /* mask time-out interrupt */
-
-/* TIMER register bits */
-#define TIMER_PERIOD_MASK BITMASK(16) /* mask for timer period */
-#define TIMER_PERIOD_DEFAULT 0xFFFF /* default timer period */
-#define TIMER_TE BIT(16) /* timer enable bit */
-
-/* PORTx_LED register bits */
-#define LED_MODE_MASK BITMASK(4)
-#define LED_MODE_INPUT 0
-#define LED_MODE_FLASH 1
-#define LED_MODE_OUT_HIGH 2
-#define LED_MODE_OUT_LOW 3
-#define LED_MODE_LINK 4
-#define LED_MODE_SPEED 5
-#define LED_MODE_DUPLEX 6
-#define LED_MODE_ACT 7
-#define LED_MODE_COLL 8
-#define LED_MODE_LINK_ACT 9
-#define LED_MODE_DUPLEX_COLL 10
-#define LED_MODE_10M_ACT 11
-#define LED_MODE_100M_ACT 12
-#define LED0_MODE_SHIFT 0 /* LED0 mode shift */
-#define LED1_MODE_SHIFT 4 /* LED1 mode shift */
-#define LED2_MODE_SHIFT 8 /* LED2 mode shift */
-#define LED0_IV_SHIFT 12 /* LED0 input value shift */
-#define LED1_IV_SHIFT 13 /* LED1 input value shift */
-#define LED2_IV_SHIFT 14 /* LED2 input value shift */
-
-#endif /* _MACH_ADM5120_SWITCH_H */
+++ /dev/null
-/*
- * ADM5120 UART definitions
- *
- * This header file defines the hardware registers of the ADM5120 SoC
- * built-in UARTs.
- *
- * Copyright (C) 2007 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MACH_ADM5120_UART_H
-#define _MACH_ADM5120_UART_H
-
-#define UART_BAUDDIV(clk, baud) ((clk/(16 * (baud)))-1)
-
-#define UART_REG_DATA 0x00
-#define UART_REG_RSR 0x04
-#define UART_REG_ECR UART_REG_RSR
-#define UART_REG_LCRH 0x08
-#define UART_REG_LCRM 0x0C
-#define UART_REG_LCRL 0x10
-#define UART_REG_CTRL 0x14
-#define UART_REG_FLAG 0x18
-
-/* Receive Status Register bits */
-#define UART_RSR_FE ( 1 << 0 )
-#define UART_RSR_PE ( 1 << 1 )
-#define UART_RSR_BE ( 1 << 2 )
-#define UART_RSR_OE ( 1 << 3 )
-#define UART_RSR_ERR ( UART_RSR_FE | UART_RSR_PE | UART_RSR_BE )
-
-#define UART_ECR_ALL 0xFF
-
-/* Line Control High register bits */
-#define UART_LCRH_BRK ( 1 << 0 ) /* send break */
-#define UART_LCRH_PEN ( 1 << 1 ) /* parity enable */
-#define UART_LCRH_EPS ( 1 << 2 ) /* even parity select */
-#define UART_LCRH_STP1 ( 0 << 3 ) /* one stop bits select */
-#define UART_LCRH_STP2 ( 1 << 3 ) /* two stop bits select */
-#define UART_LCRH_FEN ( 1 << 4 ) /* FIFO enable */
-
-#define UART_LCRH_WLEN5 ( 0 << 5 )
-#define UART_LCRH_WLEN6 ( 1 << 5 )
-#define UART_LCRH_WLEN7 ( 2 << 5 )
-#define UART_LCRH_WLEN8 ( 3 << 5 )
-
-/* Control register bits */
-#define UART_CTRL_EN ( 1 << 0 )
-
-/* Flag register bits */
-#define UART_FLAG_CTS ( 1 << 0 )
-#define UART_FLAG_DSR ( 1 << 1 )
-#define UART_FLAG_DCD ( 1 << 2 )
-#define UART_FLAG_BUSY ( 1 << 3 )
-#define UART_FLAG_RXFE ( 1 << 4 )
-#define UART_FLAG_TXFF ( 1 << 5 )
-#define UART_FLAG_RXFF ( 1 << 6 )
-#define UART_FLAG_TXFE ( 1 << 7 )
-
-#endif /* _MACH_ADM5120_UART_H */
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-/* DO NOT EDIT!! - this file automatically generated
- * from .s file by awk -f s2h.awk
- */
-/* Size definitions
- * Copyright (C) ARM Limited 1998. All rights reserved.
- */
-
-#ifndef __sizes_h
-#define __sizes_h 1
-
-/* handy sizes */
-#define SZ_16 0x00000010
-#define SZ_256 0x00000100
-#define SZ_512 0x00000200
-
-#define SZ_1K 0x00000400
-#define SZ_4K 0x00001000
-#define SZ_8K 0x00002000
-#define SZ_16K 0x00004000
-#define SZ_64K 0x00010000
-#define SZ_128K 0x00020000
-#define SZ_256K 0x00040000
-#define SZ_512K 0x00080000
-
-#define SZ_1M 0x00100000
-#define SZ_2M 0x00200000
-#define SZ_4M 0x00400000
-#define SZ_8M 0x00800000
-#define SZ_16M 0x01000000
-#define SZ_32M 0x02000000
-#define SZ_64M 0x04000000
-#define SZ_128M 0x08000000
-#define SZ_256M 0x10000000
-#define SZ_512M 0x20000000
-
-#define SZ_1G 0x40000000
-#define SZ_2G 0x80000000
-
-#endif
-
-/* END */
+++ /dev/null
-/*
- * ADM5120 specific CPU feature overrides
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This file was derived from: include/asm-mips/cpu-features.h
- * Copyright (C) 2003, 2004 Ralf Baechle
- * Copyright (C) 2004 Maciej W. Rozycki
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-#ifndef __ASM_MACH_ADM5120_CPU_FEATURE_OVERRIDES_H
-#define __ASM_MACH_ADM5120_CPU_FEATURE_OVERRIDES_H
-
-/*
- * The ADM5120 SOC has a built-in MIPS 4Kc core.
- */
-#define cpu_has_tlb 1
-#define cpu_has_4kex 1
-#define cpu_has_3k_cache 0
-#define cpu_has_4k_cache 1
-#define cpu_has_tx39_cache 0
-#define cpu_has_sb1_cache 0
-#define cpu_has_fpu 0
-#define cpu_has_32fpr 0
-#define cpu_has_counter 1
-#define cpu_has_watch 1
-#define cpu_has_divec 1
-/* #define cpu_has_vce ? */
-/* #define cpu_has_cache_cdex_p ? */
-/* #define cpu_has_cache_cdex_s ? */
-#define cpu_has_prefetch 1
-/* #define cpu_has_mcheck ? */
-#define cpu_has_ejtag 1
-#define cpu_has_llsc 1
-
-#define cpu_has_mips16 0
-#define cpu_has_mdmx 0
-#define cpu_has_mips3d 0
-#define cpu_has_smartmips 0
-
-/* #define cpu_has_vtag_icache ? */
-/* #define cpu_has_dc_aliases ? */
-/* #define cpu_has_ic_fills_f_dc ? */
-/* #define cpu_has_pindexed_dcache ? */
-
-/* #define cpu_icache_snoops_remote_store ? */
-
-#define cpu_has_mips32r1 1
-#define cpu_has_mips32r2 0
-#define cpu_has_mips64r1 0
-#define cpu_has_mips64r2 0
-
-#define cpu_has_dsp 0
-#define cpu_has_mipsmt 0
-
-/* #define cpu_has_nofpuex ? */
-#define cpu_has_64bits 0
-#define cpu_has_64bit_zero_reg 0
-#define cpu_has_64bit_gp_regs 0
-#define cpu_has_64bit_addresses 0
-
-/* #define cpu_has_inclusive_pcaches ? */
-
-#define cpu_dcache_line_size() 16
-#define cpu_icache_line_size() 16
-
-#endif /* __ASM_MACH_ADM5120_CPU_FEATURE_OVERRIDES_H */
+++ /dev/null
-/*
- * ADM5120 GPIO wrappers for arch-neutral GPIO calls
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _ASM_MIPS_MACH_ADM5120_GPIO_H
-#define _ASM_MIPS_MACH_ADM5120_GPIO_H
-
-#define ARCH_NR_GPIOS 64
-
-#include <asm-generic/gpio.h>
-
-#include <asm/mach-adm5120/adm5120_switch.h>
-
-#define ADM5120_GPIO_PIN0 0
-#define ADM5120_GPIO_PIN1 1
-#define ADM5120_GPIO_PIN2 2
-#define ADM5120_GPIO_PIN3 3
-#define ADM5120_GPIO_PIN4 4
-#define ADM5120_GPIO_PIN5 5
-#define ADM5120_GPIO_PIN6 6
-#define ADM5120_GPIO_PIN7 7
-#define ADM5120_GPIO_P0L0 8
-#define ADM5120_GPIO_P0L1 9
-#define ADM5120_GPIO_P0L2 10
-#define ADM5120_GPIO_P1L0 11
-#define ADM5120_GPIO_P1L1 12
-#define ADM5120_GPIO_P1L2 13
-#define ADM5120_GPIO_P2L0 14
-#define ADM5120_GPIO_P2L1 15
-#define ADM5120_GPIO_P2L2 16
-#define ADM5120_GPIO_P3L0 17
-#define ADM5120_GPIO_P3L1 18
-#define ADM5120_GPIO_P3L2 19
-#define ADM5120_GPIO_P4L0 20
-#define ADM5120_GPIO_P4L1 21
-#define ADM5120_GPIO_P4L2 22
-#define ADM5120_GPIO_MAX 22
-#define ADM5120_GPIO_COUNT ADM5120_GPIO_MAX+1
-
-#define ADM5120_GPIO_LOW 0
-#define ADM5120_GPIO_HIGH 1
-
-#define ADM5120_GPIO_SWITCH 0x10
-#define ADM5120_GPIO_FLASH (ADM5120_GPIO_SWITCH | LED_MODE_FLASH)
-#define ADM5120_GPIO_LINK (ADM5120_GPIO_SWITCH | LED_MODE_LINK)
-#define ADM5120_GPIO_SPEED (ADM5120_GPIO_SWITCH | LED_MODE_SPEED)
-#define ADM5120_GPIO_DUPLEX (ADM5120_GPIO_SWITCH | LED_MODE_DUPLEX)
-#define ADM5120_GPIO_ACT (ADM5120_GPIO_SWITCH | LED_MODE_ACT)
-#define ADM5120_GPIO_COLL (ADM5120_GPIO_SWITCH | LED_MODE_COLL)
-#define ADM5120_GPIO_LINK_ACT (ADM5120_GPIO_SWITCH | LED_MODE_LINK_ACT)
-#define ADM5120_GPIO_DUPLEX_COLL (ADM5120_GPIO_SWITCH | LED_MODE_DUPLEX_COLL)
-#define ADM5120_GPIO_10M_ACT (ADM5120_GPIO_SWITCH | LED_MODE_10M_ACT)
-#define ADM5120_GPIO_100M_ACT (ADM5120_GPIO_SWITCH | LED_MODE_100M_ACT)
-
-extern int __adm5120_gpio0_get_value(unsigned gpio);
-extern void __adm5120_gpio0_set_value(unsigned gpio, int value);
-extern int __adm5120_gpio1_get_value(unsigned gpio);
-extern void __adm5120_gpio1_set_value(unsigned gpio, int value);
-extern int adm5120_gpio_to_irq(unsigned gpio);
-extern int adm5120_irq_to_gpio(unsigned irq);
-
-static inline int gpio_get_value(unsigned gpio)
-{
- int ret;
-
- switch (gpio) {
- case ADM5120_GPIO_PIN0 ... ADM5120_GPIO_PIN7:
- ret = __adm5120_gpio0_get_value(gpio);
- break;
- case ADM5120_GPIO_P0L0 ... ADM5120_GPIO_P4L2:
- ret = __adm5120_gpio1_get_value(gpio - ADM5120_GPIO_P0L0);
- break;
- default:
- ret = __gpio_get_value(gpio);
- break;
- }
-
- return ret;
-}
-
-static inline void gpio_set_value(unsigned gpio, int value)
-{
- switch (gpio) {
- case ADM5120_GPIO_PIN0 ... ADM5120_GPIO_PIN7:
- __adm5120_gpio0_set_value(gpio, value);
- break;
- case ADM5120_GPIO_P0L0 ... ADM5120_GPIO_P4L2:
- __adm5120_gpio1_set_value(gpio - ADM5120_GPIO_P0L0, value);
- break;
- default:
- __gpio_set_value(gpio, value);
- break;
- }
-}
-
-static inline int gpio_to_irq(unsigned gpio)
-{
- return adm5120_gpio_to_irq(gpio);
-}
-
-static inline int irq_to_gpio(unsigned irq)
-{
- return adm5120_irq_to_gpio(irq);
-}
-
-#define gpio_cansleep __gpio_cansleep
-
-#endif /* _ASM_MIPS_MACH_ADM5120_GPIO_H */
+++ /dev/null
-/*
- * ADM5120 specific IRQ numbers
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-#ifndef _ASM_MIPS_MACH_ADM5120_IRQ_H
-#define _ASM_MIPS_MACH_ADM5120_IRQ_H
-
-#define MIPS_CPU_IRQ_BASE 0
-#define NR_IRQS 24
-
-#include_next <irq.h>
-
-#include <asm/mach-adm5120/adm5120_intc.h>
-
-#define NO_IRQ (-1)
-
-#define MIPS_CPU_IRQ_COUNT 8
-#define MIPS_CPU_IRQ(x) (MIPS_CPU_IRQ_BASE + (x))
-
-#define ADM5120_INTC_IRQ_BASE (MIPS_CPU_IRQ_BASE + MIPS_CPU_IRQ_COUNT)
-#define ADM5120_INTC_IRQ(x) (ADM5120_INTC_IRQ_BASE + (x))
-
-#define ADM5120_IRQ_INTC MIPS_CPU_IRQ(2)
-#define ADM5120_IRQ_COUNTER MIPS_CPU_IRQ(7)
-
-#define ADM5120_IRQ_TIMER ADM5120_INTC_IRQ(INTC_IRQ_TIMER)
-#define ADM5120_IRQ_UART0 ADM5120_INTC_IRQ(INTC_IRQ_UART0)
-#define ADM5120_IRQ_UART1 ADM5120_INTC_IRQ(INTC_IRQ_UART1)
-#define ADM5120_IRQ_USBC ADM5120_INTC_IRQ(INTC_IRQ_USBC)
-#define ADM5120_IRQ_GPIO2 ADM5120_INTC_IRQ(INTC_IRQ_GPIO2)
-#define ADM5120_IRQ_GPIO4 ADM5120_INTC_IRQ(INTC_IRQ_GPIO4)
-#define ADM5120_IRQ_PCI0 ADM5120_INTC_IRQ(INTC_IRQ_PCI0)
-#define ADM5120_IRQ_PCI1 ADM5120_INTC_IRQ(INTC_IRQ_PCI1)
-#define ADM5120_IRQ_PCI2 ADM5120_INTC_IRQ(INTC_IRQ_PCI2)
-#define ADM5120_IRQ_SWITCH ADM5120_INTC_IRQ(INTC_IRQ_SWITCH)
-
-#endif /* _ASM_MIPS_MACH_ADM5120_IRQ_H */
+++ /dev/null
-/*
- * ADMBoot specific definitions
- *
- * Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _ADMBOOT_H
-#define _ADMBOOT_H
-
-extern int admboot_get_mac_base(u32 offset, u32 len, u8 *mac) __init;
-
-#endif /* _ADMBOOT_H */
+++ /dev/null
-/*
- * Broadcom's CFE definitions
- *
- * Copyright (C) 2006-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _PROM_CFE_H_
-#define _PROM_CFE_H_
-
-extern int cfe_present(void) __init;
-extern char *cfe_getenv(char *);
-
-#endif /*_PROM_CFE_H_*/
+++ /dev/null
-/*
- * Generic prom definitions
- *
- * Copyright (C) 2006-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _PROM_GENERIC_H_
-#define _PROM_GENERIC_H_
-
-extern int generic_prom_present(void) __init;
-extern char *generic_prom_getenv(char *);
-
-#endif /*_PROM_GENERIC_H_*/
+++ /dev/null
-/*
- * Compex's MyLoader specific definitions
- *
- * Copyright (C) 2006-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _MYLOADER_H_
-#define _MYLOADER_H_
-
-/*
- * Firmware file format:
- *
- * <header>
- * [<block descriptor 0>]
- * ...
- * [<block descriptor n>]
- * <null block descriptor>
- * [<block data 0>]
- * ...
- * [<block data n>]
- *
- *
- */
-
-/* Myloader specific magic numbers */
-#define MYLO_MAGIC_FIRMWARE 0x4C594D00
-#define MYLO_MAGIC_20021103 0x20021103
-#define MYLO_MAGIC_20021107 0x20021107
-
-#define MYLO_MAGIC_SYS_PARAMS MYLO_MAGIC_20021107
-#define MYLO_MAGIC_PARTITIONS MYLO_MAGIC_20021103
-#define MYLO_MAGIC_BOARD_PARAMS MYLO_MAGIC_20021103
-
-/*
- * Addresses of the data structures provided by MyLoader
- */
-#define MYLO_MIPS_SYS_PARAMS 0x80000800 /* System Parameters */
-#define MYLO_MIPS_BOARD_PARAMS 0x80000A00 /* Board Parameters */
-#define MYLO_MIPS_PARTITIONS 0x80000C00 /* Partition Table */
-#define MYLO_MIPS_BOOT_PARAMS 0x80000E00 /* Boot Parameters */
-
-/* Vendor ID's (seems to be same as the PCI vendor ID's) */
-#define VENID_COMPEX 0x11F6
-
-/* Devices based on the ADM5120 */
-#define DEVID_COMPEX_NP27G 0x0078
-#define DEVID_COMPEX_NP28G 0x044C
-#define DEVID_COMPEX_NP28GHS 0x044E
-#define DEVID_COMPEX_WP54Gv1C 0x0514
-#define DEVID_COMPEX_WP54G 0x0515
-#define DEVID_COMPEX_WP54AG 0x0546
-#define DEVID_COMPEX_WPP54AG 0x0550
-#define DEVID_COMPEX_WPP54G 0x0555
-
-/* Devices based on the IXP422 */
-#define DEVID_COMPEX_WP18 0x047E
-#define DEVID_COMPEX_NP18A 0x0489
-
-/* Other devices */
-#define DEVID_COMPEX_NP26G8M 0x03E8
-#define DEVID_COMPEX_NP26G16M 0x03E9
-
-struct mylo_fw_header {
- uint32_t magic; /* must be MYLO_MAGIC_FIRMWARE */
- uint32_t crc; /* CRC of the whole firmware */
- uint32_t res0; /* unknown/unused */
- uint32_t res1; /* unknown/unused */
- uint16_t vid; /* vendor ID */
- uint16_t did; /* device ID */
- uint16_t svid; /* sub vendor ID */
- uint16_t sdid; /* sub device ID */
- uint32_t rev; /* device revision */
- uint32_t fwhi; /* FIXME: firmware version high? */
- uint32_t fwlo; /* FIXME: firmware version low? */
- uint32_t flags; /* firmware flags */
-};
-
-#define FW_FLAG_BOARD_PARAMS_WP 0x01 /* board parameters are write protected */
-#define FW_FLAG_BOOT_SECTOR_WE 0x02 /* enable of write boot sectors (below 64K) */
-
-struct mylo_fw_blockdesc {
- uint32_t type; /* block type */
- uint32_t addr; /* relative address to flash start */
- uint32_t dlen; /* size of block data in bytes */
- uint32_t blen; /* total size of block in bytes */
-};
-
-#define FW_DESC_TYPE_UNUSED 0
-#define FW_DESC_TYPE_USED 1
-
-struct mylo_partition {
- uint16_t flags; /* partition flags */
- uint16_t type; /* type of the partition */
- uint32_t addr; /* relative address of the partition from the
- flash start */
- uint32_t size; /* size of the partition in bytes */
- uint32_t param; /* if this is the active partition, the
- MyLoader load code to this address */
-};
-
-#define PARTITION_FLAG_ACTIVE 0x8000 /* this is the active partition,
- * MyLoader loads firmware from here */
-#define PARTITION_FLAG_ISRAM 0x2000 /* FIXME: this is a RAM partition? */
-#define PARTIIION_FLAG_RAMLOAD 0x1000 /* FIXME: load this partition into the RAM? */
-#define PARTITION_FLAG_PRELOAD 0x0800 /* the partition data preloaded to RAM
- * before decompression */
-#define PARTITION_FLAG_HAVEHDR 0x0002 /* the partition data have a header */
-
-#define PARTITION_TYPE_FREE 0
-#define PARTITION_TYPE_USED 1
-
-#define MYLO_MAX_PARTITIONS 8 /* maximum number of partitions in the
- partition table */
-
-struct mylo_partition_table {
- uint32_t magic; /* must be MYLO_MAGIC_PARTITIONS */
- uint32_t res0; /* unknown/unused */
- uint32_t res1; /* unknown/unused */
- uint32_t res2; /* unknown/unused */
- struct mylo_partition partitions[MYLO_MAX_PARTITIONS];
-};
-
-struct mylo_partition_header {
- uint32_t len; /* length of the partition data */
- uint32_t crc; /* CRC value of the partition data */
-};
-
-struct mylo_system_params {
- uint32_t magic; /* must be MYLO_MAGIC_SYS_PARAMS */
- uint32_t res0;
- uint32_t res1;
- uint32_t mylo_ver;
- uint16_t vid; /* Vendor ID */
- uint16_t did; /* Device ID */
- uint16_t svid; /* Sub Vendor ID */
- uint16_t sdid; /* Sub Device ID */
- uint32_t rev; /* device revision */
- uint32_t fwhi;
- uint32_t fwlo;
- uint32_t tftp_addr;
- uint32_t prog_start;
- uint32_t flash_size; /* Size of boot FLASH in bytes */
- uint32_t dram_size; /* Size of onboard RAM in bytes */
-};
-
-
-struct mylo_eth_addr {
- uint8_t mac[6];
- uint8_t csum[2];
-};
-
-#define MYLO_ETHADDR_COUNT 8 /* maximum number of ethernet address
- in the board parameters */
-
-struct mylo_board_params {
- uint32_t magic; /* must be MYLO_MAGIC_BOARD_PARAMS */
- uint32_t res0;
- uint32_t res1;
- uint32_t res2;
- struct mylo_eth_addr addr[MYLO_ETHADDR_COUNT];
-};
-
-struct myloader_info {
- u32 vid;
- u32 did;
- u32 svid;
- u32 sdid;
- uint8_t macs[MYLO_ETHADDR_COUNT][6];
-};
-
-extern struct myloader_info myloader_info;
-extern int myloader_present(void) __init;
-
-#endif /* _MYLOADER_H_*/
+++ /dev/null
-/*
- * Mikrotik's RouterBOOT definitions
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _ROUTERBOOT_H
-#define _ROUTERBOOT_H
-
-#define RB_MAC_SIZE 6
-
-struct rb_bios_settings {
- u32 hs_offs; /* hard settings offset */
- u32 hs_size; /* hard settings size */
- u32 fw_offs; /* firmware offset */
- u32 ss_offs; /* soft settings offset */
- u32 ss_size; /* soft settings size */
-};
-
-struct rb_hard_settings {
- char *name; /* board name */
- char *bios_ver; /* BIOS version */
- u32 mem_size; /* memory size in bytes */
- u32 mac_count; /* number of mac addresses */
- u8 *mac_base; /* mac address base */
-};
-
-/*
- * Magic numbers
- */
-#define RB_MAGIC_HARD 0x64726148 /* "Hard" */
-#define RB_MAGIC_SOFT 0x74666F53 /* "Soft" */
-#define RB_MAGIC_DAWN 0x6E776144 /* "Dawn" */
-
-#define RB_ID_TERMINATOR 0
-
-/*
- * ID values for Hardware settings
- */
-#define RB_ID_HARD_01 1
-#define RB_ID_HARD_02 2
-#define RB_ID_FLASH_INFO 3
-#define RB_ID_MAC_ADDRESS_PACK 4
-#define RB_ID_BOARD_NAME 5
-#define RB_ID_BIOS_VERSION 6
-#define RB_ID_HARD_07 7
-#define RB_ID_SDRAM_TIMINGS 8
-#define RB_ID_DEVICE_TIMINGS 9
-#define RB_ID_SOFTWARE_ID 10
-#define RB_ID_SERIAL_NUMBER 11
-#define RB_ID_HARD_12 12
-#define RB_ID_MEMORY_SIZE 13
-#define RB_ID_MAC_ADDRESS_COUNT 14
-
-/*
- * ID values for Software settings
- */
-#define RB_ID_UART_SPEED 1
-#define RB_ID_BOOT_DELAY 2
-#define RB_ID_BOOT_DEVICE 3
-#define RB_ID_BOOT_KEY 4
-#define RB_ID_CPU_MODE 5
-#define RB_ID_FW_VERSION 6
-#define RB_ID_SOFT_07 7
-#define RB_ID_SOFT_08 8
-#define RB_ID_BOOT_PROTOCOL 9
-#define RB_ID_SOFT_10 10
-#define RB_ID_SOFT_11 11
-
-/*
- * UART_SPEED values
- */
-#define RB_UART_SPEED_115200 0
-#define RB_UART_SPEED_57600 1
-#define RB_UART_SPEED_38400 2
-#define RB_UART_SPEED_19200 3
-#define RB_UART_SPEED_9600 4
-#define RB_UART_SPEED_4800 5
-#define RB_UART_SPEED_2400 6
-#define RB_UART_SPEED_1200 7
-
-/*
- * BOOT_DELAY values
- */
-#define RB_BOOT_DELAY_0SEC 0
-#define RB_BOOT_DELAY_1SEC 1
-#define RB_BOOT_DELAY_2SEC 2
-
-/*
- * BOOT_DEVICE values
- */
-#define RB_BOOT_DEVICE_ETHER 0
-#define RB_BOOT_DEVICE_NANDETH 1
-#define RB_BOOT_DEVICE_ETHONCE 2
-#define RB_BOOT_DEVICE_NANDONLY 3
-
-/*
- * BOOT_KEY values
- */
-#define RB_BOOT_KEY_ANY 0
-#define RB_BOOT_KEY_DEL 1
-
-/*
- * CPU_MODE values
- */
-#define RB_CPU_MODE_POWERSAVE 0
-#define RB_CPU_MODE_REGULAR 1
-
-/*
- * BOOT_PROTOCOL values
- */
-#define RB_BOOT_PROTOCOL_BOOTP 0
-#define RB_BOOT_PROTOCOL_DHCP 1
-
-extern int routerboot_present(void) __init;
-extern char *routerboot_get_boardname(void);
-
-extern struct rb_hard_settings rb_hs;
-
-#endif /* _ROUTERBOOT_H */
+++ /dev/null
-/*
- * ZyNOS (ZyXEL's Networking OS) definitions
- *
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-
-#ifndef _ZYNOS_H
-#define _ZYNOS_H
-
-#define ZYNOS_NAME_LEN 32
-#define ZYNOS_FEAT_BYTES 22
-#define ZYNOS_MAC_LEN 6
-
-struct zynos_board_info {
- unsigned char vendor[ZYNOS_NAME_LEN];
- unsigned char product[ZYNOS_NAME_LEN];
- u32 bootext_addr;
- u32 res0;
- u16 board_id;
- u8 res1[6];
- u8 feat_other[ZYNOS_FEAT_BYTES];
- u8 feat_main;
- u8 res2;
- u8 mac[ZYNOS_MAC_LEN];
- u8 country;
- u8 dbgflag;
-} __attribute__ ((packed));
-
-/*
- * Vendor IDs
- */
-#define ZYNOS_VENDOR_ID_ZYXEL 0
-#define ZYNOS_VENDOR_ID_NETGEAR 1
-#define ZYNOS_VENDOR_ID_DLINK 2
-#define ZYNOS_VENDOR_ID_OTHER 3
-#define ZYNOS_VENDOR_ID_LUCENT 4
-
-/*
- * Vendor names
- */
-#define ZYNOS_VENDOR_DLINK "D-Link"
-#define ZYNOS_VENDOR_LUCENT "LUCENT"
-#define ZYNOS_VENDOR_NETGEAR "NetGear"
-#define ZYNOS_VENDOR_ZYXEL "ZyXEL"
-
-/*
- * Board IDs (big-endian)
- */
-#define ZYNOS_BOARD_ES2108 0x00F2 /* Ethernet Switch 2108 */
-#define ZYNOS_BOARD_ES2108F 0x01AF /* Ethernet Switch 2108-F */
-#define ZYNOS_BOARD_ES2108G 0x00F3 /* Ethernet Switch 2108-G */
-#define ZYNOS_BOARD_ES2108LC 0x00FC /* Ethernet Switch 2108-LC */
-#define ZYNOS_BOARD_ES2108PWR 0x00F4 /* Ethernet Switch 2108PWR */
-#define ZYNOS_BOARD_HS100 0x9FF1 /* HomeSafe 100/100W */
-#define ZYNOS_BOARD_P334 0x9FF5 /* Prestige 334 */
-#define ZYNOS_BOARD_P334U 0x9FDD /* Prestige 334U */
-#define ZYNOS_BOARD_P334W 0x9FF3 /* Prestige 334W */
-#define ZYNOS_BOARD_P334WH 0x00E0 /* Prestige 334WH */
-#define ZYNOS_BOARD_P334WHD 0x00E1 /* Prestige 334WHD */
-#define ZYNOS_BOARD_P334WT 0x9FEF /* Prestige 334WT */
-#define ZYNOS_BOARD_P334WT_ALT 0x9F02 /* Prestige 334WT alternative*/
-#define ZYNOS_BOARD_P335 0x9FED /* Prestige 335/335WT */
-#define ZYNOS_BOARD_P335PLUS 0x0025 /* Prestige 335Plus */
-#define ZYNOS_BOARD_P335U 0x9FDC /* Prestige 335U */
-
-/*
- * Some magic numbers (big-endian)
- */
-#define ZYNOS_MAGIC_DBGAREA1 0x48646267 /* "Hdbg" */
-#define ZYNOS_MAGIC_DBGAREA2 0x61726561 /* "area" */
-
-struct bootbase_info {
- u16 vendor_id;
- u16 board_id;
- u8 mac[6];
-};
-
-extern struct bootbase_info bootbase_info;
-extern int bootbase_present(void) __init;
-
-#endif /* _ZYNOS_H */
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2002, 2004, 2007 by Ralf Baechle <ralf@linux-mips.org>
- */
-#ifndef __ASM_MIPS_MACH_ADM5120_WAR_H
-#define __ASM_MIPS_MACH_ADM5120_WAR_H
-
-#define R4600_V1_INDEX_ICACHEOP_WAR 0
-#define R4600_V1_HIT_CACHEOP_WAR 0
-#define R4600_V2_HIT_CACHEOP_WAR 0
-#define R5432_CP0_INTERRUPT_WAR 0
-#define BCM1250_M3_WAR 0
-#define SIBYTE_1956_WAR 0
-#define MIPS4K_ICACHE_REFILL_WAR 0
-#define MIPS_CACHE_SYNC_WAR 0
-#define TX49XX_ICACHE_INDEX_INV_WAR 0
-#define RM9000_CDEX_SMP_WAR 0
-#define ICACHE_REFILLS_WORKAROUND_WAR 0
-#define R10000_LLSC_WAR 0
-#define MIPS34K_MISSED_ITLB_WAR 0
-
-#endif /* __ASM_MIPS_MACH_ADM5120_WAR_H */
projects / openwrt / staging / dedeckeh.git / commitdiff