package/mac80211/src/net/mac80211/Kconfig

   1 config MAC80211
   2         tristate "Generic IEEE 802.11 Networking Stack (mac80211)"
   3         select CRYPTO
   4         select CRYPTO_ECB
   5         select CRYPTO_ARC4
   6         select CRYPTO_AES
   7         select CRC32
   8         select WIRELESS_EXT
   9         select CFG80211
  10         select NET_SCH_FIFO
  11         ---help---
  12           This option enables the hardware independent IEEE 802.11
  13           networking stack.
  14
  15 menu "Rate control algorithm selection"
  16         depends on MAC80211 != n
  17
  18 choice
  19         prompt "Default rate control algorithm"
  20         default MAC80211_RC_DEFAULT_PID
  21         ---help---
  22           This option selects the default rate control algorithm
  23           mac80211 will use. Note that this default can still be
  24           overriden through the ieee80211_default_rc_algo module
  25           parameter if different algorithms are available.
  26
  27 config MAC80211_RC_DEFAULT_PID
  28         bool "PID controller based rate control algorithm"
  29         select MAC80211_RC_PID
  30         ---help---
  31           Select the PID controller based rate control as the
  32           default rate control algorithm. You should choose
  33           this unless you know what you are doing.
  34
  35 config MAC80211_RC_DEFAULT_SIMPLE
  36         bool "Simple rate control algorithm"
  37         select MAC80211_RC_SIMPLE
  38         ---help---
  39           Select the simple rate control as the default rate
  40           control algorithm. Note that this is a non-responsive,
  41           dumb algorithm. You should choose the PID rate control
  42           instead.
  43
  44 config MAC80211_RC_DEFAULT_NONE
  45         bool "No default algorithm"
  46         depends on EMBEDDED
  47         help
  48           Selecting this option will select no default algorithm
  49           and allow you to not build any. Do not choose this
  50           option unless you know your driver comes with another
  51           suitable algorithm.
  52 endchoice
  53
  54 comment "Selecting 'y' for an algorithm will"
  55 comment "build the algorithm into mac80211."
  56
  57 config MAC80211_RC_DEFAULT
  58         string
  59         default "pid" if MAC80211_RC_DEFAULT_PID
  60         default "simple" if MAC80211_RC_DEFAULT_SIMPLE
  61         default ""
  62
  63 config MAC80211_RC_PID
  64         tristate "PID controller based rate control algorithm"
  65         ---help---
  66           This option enables a TX rate control algorithm for
  67           mac80211 that uses a PID controller to select the TX
  68           rate.
  69
  70           Say Y or M unless you're sure you want to use a
  71           different rate control algorithm.
  72
  73 config MAC80211_RC_SIMPLE
  74         tristate "Simple rate control algorithm (DEPRECATED)"
  75         ---help---
  76           This option enables a very simple, non-responsive TX
  77           rate control algorithm. This algorithm is deprecated
  78           and will be removed from the kernel in the near future.
  79           It has been replaced by the PID algorithm.
  80
  81           Say N unless you know what you are doing.
  82 endmenu
  83
  84 config MAC80211_LEDS
  85         bool "Enable LED triggers"
  86         depends on MAC80211 && LEDS_TRIGGERS
  87         ---help---
  88           This option enables a few LED triggers for different
  89           packet receive/transmit events.
  90
  91 config MAC80211_DEBUGFS
  92         bool "Export mac80211 internals in DebugFS"
  93         depends on MAC80211 && DEBUG_FS
  94         ---help---
  95           Select this to see extensive information about
  96           the internal state of mac80211 in debugfs.
  97
  98           Say N unless you know you need this.
  99
 100 config MAC80211_DEBUG_PACKET_ALIGNMENT
 101         bool "Enable packet alignment debugging"
 102         depends on MAC80211
 103         help
 104           This option is recommended for driver authors and strongly
 105           discouraged for everybody else, it will trigger a warning
 106           when a driver hands mac80211 a buffer that is aligned in
 107           a way that will cause problems with the IP stack on some
 108           architectures.
 109
 110           Say N unless you're writing a mac80211 based driver.
 111
 112 config MAC80211_DEBUG
 113         bool "Enable debugging output"
 114         depends on MAC80211
 115         ---help---
 116           This option will enable debug tracing output for the
 117           ieee80211 network stack.
 118
 119           If you are not trying to debug or develop the ieee80211
 120           subsystem, you most likely want to say N here.
 121
 122 config MAC80211_HT_DEBUG
 123         bool "Enable HT debugging output"
 124         depends on MAC80211_DEBUG
 125         ---help---
 126           This option enables 802.11n High Throughput features
 127           debug tracing output.
 128
 129           If you are not trying to debug of develop the ieee80211
 130           subsystem, you most likely want to say N here.
 131
 132 config MAC80211_VERBOSE_DEBUG
 133         bool "Verbose debugging output"
 134         depends on MAC80211_DEBUG
 135
 136 config MAC80211_LOWTX_FRAME_DUMP
 137         bool "Debug frame dumping"
 138         depends on MAC80211_DEBUG
 139         ---help---
 140           Selecting this option will cause the stack to
 141           print a message for each frame that is handed
 142           to the lowlevel driver for transmission. This
 143           message includes all MAC addresses and the
 144           frame control field.
 145
 146           If unsure, say N and insert the debugging code
 147           you require into the driver you are debugging.
 148
 149 config TKIP_DEBUG
 150         bool "TKIP debugging"
 151         depends on MAC80211_DEBUG
 152
 153 config MAC80211_DEBUG_COUNTERS
 154         bool "Extra statistics for TX/RX debugging"
 155         depends on MAC80211_DEBUG
 156
 157 config MAC80211_IBSS_DEBUG
 158         bool "Support for IBSS testing"
 159         depends on MAC80211_DEBUG
 160         ---help---
 161           Say Y here if you intend to debug the IBSS code.
 162
 163 config MAC80211_VERBOSE_PS_DEBUG
 164         bool "Verbose powersave mode debugging"
 165         depends on MAC80211_DEBUG
 166         ---help---
 167           Say Y here to print out verbose powersave
 168           mode debug messages.