target/linux/ramips/patches-4.3/0029-phy-usb-add-ralink-phy.patch

   1 From b00b5eafa7e8d059bd0ce844e66f648916953270 Mon Sep 17 00:00:00 2001
   2 From: John Crispin <blogic@openwrt.org>
   3 Date: Sun, 3 Jan 2016 19:11:22 +0100
   4 Subject: [PATCH 2/3] phy: ralink-usb: add driver for Mediatek/Ralink
   5
   6 Add a driver to setup the USB phy on Mediatek/Ralink SoCs.
   7 The driver is trivial and only sets up power and host mode.
   8
   9 Signed-off-by: John Crispin <blogic@openwrt.org>
  10 ---
  11  .../devicetree/bindings/phy/ralink-usb-phy.txt     |   17 ++
  12  drivers/phy/Kconfig                                |    8 +
  13  drivers/phy/Makefile                               |    1 +
  14  drivers/phy/phy-ralink-usb.c                       |  171 ++++++++++++++++++++
  15  4 files changed, 197 insertions(+)
  16  create mode 100644 Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
  17  create mode 100644 drivers/phy/phy-ralink-usb.c
  18
  19 --- /dev/null
  20 +++ b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
  21 @@ -0,0 +1,17 @@
  22 +Mediatek/Ralink USB PHY
  23 +
  24 +Required properties:
  25 + - compatible: ralink,rt3352-usbphy or mediatek,mt7620-usbphy
  26 + - #phy-cells: should be 0
  27 + - resets: the two reset controllers for host and device
  28 + - reset-names: the names of the 2 reset controllers
  29 +
  30 +Example:
  31 +
  32 +usbphy: phy {
  33 +       compatible = "mediatek,mt7620-usbphy";
  34 +       #phy-cells = <0>;
  35 +
  36 +       resets = <&rstctrl 22 &rstctrl 25>;
  37 +       reset-names = "host", "device";
  38 +};
  39 --- a/drivers/phy/Kconfig
  40 +++ b/drivers/phy/Kconfig
  41 @@ -331,6 +331,14 @@ config PHY_XGENE
  42         help
  43           This option enables support for APM X-Gene SoC multi-purpose PHY.
  44
  45 +config PHY_RALINK_USB
  46 +       tristate "Ralink USB PHY driver"
  47 +       select GENERIC_PHY
  48 +       depends on RALINK
  49 +       help
  50 +         This option enables support for the Ralink USB PHY found inside
  51 +         RT3352 and MT7620.
  52 +
  53  config PHY_STIH407_USB
  54         tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family"
  55         depends on RESET_CONTROLLER
  56 --- a/drivers/phy/Makefile
  57 +++ b/drivers/phy/Makefile
  58 @@ -46,3 +46,4 @@ obj-$(CONFIG_PHY_QCOM_UFS)    += phy-qcom-
  59  obj-$(CONFIG_PHY_TUSB1210)             += phy-tusb1210.o
  60  obj-$(CONFIG_PHY_BRCMSTB_SATA)         += phy-brcmstb-sata.o
  61  obj-$(CONFIG_PHY_PISTACHIO_USB)                += phy-pistachio-usb.o
  62 +obj-$(CONFIG_PHY_RALINK_USB)           += phy-ralink-usb.o
  63 --- /dev/null
  64 +++ b/drivers/phy/phy-ralink-usb.c
  65 @@ -0,0 +1,175 @@
  66 +/*
  67 + * Allwinner ralink USB phy driver
  68 + *
  69 + * Copyright (C) 2016 John Crispin <blogic@openwrt.org>
  70 + *
  71 + * Based on code from
  72 + * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
  73 + *
  74 + * This program is free software; you can redistribute it and/or modify
  75 + * it under the terms of the GNU General Public License as published by
  76 + * the Free Software Foundation; either version 2 of the License, or
  77 + * (at your option) any later version.
  78 + *
  79 + * This program is distributed in the hope that it will be useful,
  80 + * but WITHOUT ANY WARRANTY; without even the implied warranty of
  81 + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  82 + * GNU General Public License for more details.
  83 + */
  84 +
  85 +#include <linux/delay.h>
  86 +#include <linux/err.h>
  87 +#include <linux/io.h>
  88 +#include <linux/kernel.h>
  89 +#include <linux/module.h>
  90 +#include <linux/mutex.h>
  91 +#include <linux/phy/phy.h>
  92 +#include <linux/platform_device.h>
  93 +#include <linux/reset.h>
  94 +#include <linux/of_platform.h>
  95 +
  96 +#include <asm/mach-ralink/ralink_regs.h>
  97 +
  98 +#define RT_SYSC_REG_SYSCFG1            0x014
  99 +#define RT_SYSC_REG_CLKCFG1            0x030
 100 +#define RT_SYSC_REG_USB_PHY_CFG                0x05c
 101 +
 102 +#define RT_RSTCTRL_UDEV                        BIT(25)
 103 +#define RT_RSTCTRL_UHST                        BIT(22)
 104 +#define RT_SYSCFG1_USB0_HOST_MODE      BIT(10)
 105 +
 106 +#define MT7620_CLKCFG1_UPHY0_CLK_EN    BIT(25)
 107 +#define MT7620_CLKCFG1_UPHY1_CLK_EN    BIT(22)
 108 +#define RT_CLKCFG1_UPHY1_CLK_EN                BIT(20)
 109 +#define RT_CLKCFG1_UPHY0_CLK_EN                BIT(18)
 110 +
 111 +#define USB_PHY_UTMI_8B60M             BIT(1)
 112 +#define UDEV_WAKEUP                    BIT(0)
 113 +
 114 +struct ralink_usb_phy {
 115 +       struct reset_control    *rstdev;
 116 +       struct reset_control    *rsthost;
 117 +       u32                     clk;
 118 +       struct phy              *phy;
 119 +};
 120 +
 121 +static int ralink_usb_phy_power_on(struct phy *_phy)
 122 +{
 123 +       struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
 124 +       u32 t;
 125 +
 126 +       /* enable the phy */
 127 +       rt_sysc_m32(0, phy->clk, RT_SYSC_REG_CLKCFG1);
 128 +
 129 +       /* setup host mode */
 130 +       rt_sysc_m32(0, RT_SYSCFG1_USB0_HOST_MODE, RT_SYSC_REG_SYSCFG1);
 131 +
 132 +       /* deassert the reset lines */
 133 +       reset_control_deassert(phy->rsthost);
 134 +       reset_control_deassert(phy->rstdev);
 135 +
 136 +       /*
 137 +        * The SDK kernel had a delay of 100ms. however on device
 138 +        * testing showed that 10ms is enough
 139 +        */
 140 +       mdelay(10);
 141 +
 142 +       /* print some status info */
 143 +       t = rt_sysc_r32(RT_SYSC_REG_USB_PHY_CFG);
 144 +       dev_info(&phy->phy->dev, "remote usb device wakeup %s\n",
 145 +               (t & UDEV_WAKEUP) ? ("enabled") : ("disabled"));
 146 +       if (t & USB_PHY_UTMI_8B60M)
 147 +               dev_info(&phy->phy->dev, "UTMI 8bit 60MHz\n");
 148 +       else
 149 +               dev_info(&phy->phy->dev, "UTMI 16bit 30MHz\n");
 150 +
 151 +       return 0;
 152 +}
 153 +
 154 +static int ralink_usb_phy_power_off(struct phy *_phy)
 155 +{
 156 +       struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
 157 +
 158 +       /* disable the phy */
 159 +       rt_sysc_m32(phy->clk, 0, RT_SYSC_REG_CLKCFG1);
 160 +
 161 +       /* assert the reset lines */
 162 +       reset_control_assert(phy->rstdev);
 163 +       reset_control_assert(phy->rsthost);
 164 +
 165 +       return 0;
 166 +}
 167 +
 168 +static struct phy_ops ralink_usb_phy_ops = {
 169 +       .power_on       = ralink_usb_phy_power_on,
 170 +       .power_off      = ralink_usb_phy_power_off,
 171 +       .owner          = THIS_MODULE,
 172 +};
 173 +
 174 +static const struct of_device_id ralink_usb_phy_of_match[] = {
 175 +       {
 176 +               .compatible = "ralink,rt3352-usbphy",
 177 +               .data = (void *) (RT_CLKCFG1_UPHY1_CLK_EN |
 178 +                                 RT_CLKCFG1_UPHY0_CLK_EN)
 179 +       },
 180 +       {
 181 +               .compatible = "mediatek,mt7620-usbphy",
 182 +               .data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
 183 +                                 MT7620_CLKCFG1_UPHY0_CLK_EN) },
 184 +       { },
 185 +};
 186 +MODULE_DEVICE_TABLE(of, ralink_usb_phy_of_match);
 187 +
 188 +static int ralink_usb_phy_probe(struct platform_device *pdev)
 189 +{
 190 +       struct device *dev = &pdev->dev;
 191 +       struct phy_provider *phy_provider;
 192 +       const struct of_device_id *match;
 193 +       struct ralink_usb_phy *phy;
 194 +
 195 +       phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
 196 +       if (!phy)
 197 +               return -ENOMEM;
 198 +
 199 +       match = of_match_device(ralink_usb_phy_of_match, &pdev->dev);
 200 +       if (!match)
 201 +               return -ENODEV;
 202 +
 203 +       phy->clk = (int) match->data;
 204 +
 205 +       phy->rsthost = devm_reset_control_get(&pdev->dev, "host");
 206 +       if (IS_ERR(phy->rsthost)) {
 207 +               dev_err(dev, "host reset is missing\n");
 208 +               return PTR_ERR(phy->rsthost);
 209 +       }
 210 +
 211 +       phy->rstdev = devm_reset_control_get(&pdev->dev, "device");
 212 +       if (IS_ERR(phy->rstdev)) {
 213 +               dev_err(dev, "device reset is missing\n");
 214 +               return PTR_ERR(phy->rstdev);
 215 +       }
 216 +
 217 +       phy->phy = devm_phy_create(dev, NULL, &ralink_usb_phy_ops);
 218 +       if (IS_ERR(phy->phy)) {
 219 +               dev_err(dev, "failed to create PHY\n");
 220 +               return PTR_ERR(phy->phy);
 221 +       }
 222 +       phy_set_drvdata(phy->phy, phy);
 223 +
 224 +       phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 225 +
 226 +       return PTR_ERR_OR_ZERO(phy_provider);
 227 +}
 228 +
 229 +static struct platform_driver ralink_usb_phy_driver = {
 230 +       .probe  = ralink_usb_phy_probe,
 231 +       .driver = {
 232 +               .of_match_table = ralink_usb_phy_of_match,
 233 +               .name  = "ralink-usb-phy",
 234 +       }
 235 +};
 236 +module_platform_driver(ralink_usb_phy_driver);
 237 +
 238 +MODULE_DESCRIPTION("Ralink USB phy driver");
 239 +MODULE_AUTHOR("John Crispin <blogic@openwrt.org>");
 240 +MODULE_LICENSE("GPL v2");