target/linux/ath79/dts/ar9331_alfa-network_ap121f.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "ar9331.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         model = "ALFA Network AP121F";
  10         compatible = "alfa-network,ap121f", "qca,ar9331";
  11
  12         aliases {
  13                 label-mac-device = &wmac;
  14                 led-boot = &led_vpn;
  15                 led-failsafe = &led_vpn;
  16                 led-upgrade = &led_vpn;
  17                 serial0 = &uart;
  18         };
  19
  20         keys {
  21                 compatible = "gpio-keys";
  22
  23                 reset {
  24                         label = "reset";
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 switch {
  30                         label = "switch";
  31                         linux,code = <BTN_0>;
  32                         gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
  33                 };
  34         };
  35
  36         leds {
  37                 compatible = "gpio-leds";
  38
  39                 lan {
  40                         label = "ap121f:green:lan";
  41                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  42                 };
  43
  44                 led_vpn: vpn {
  45                         label = "ap121f:green:vpn";
  46                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  47                 };
  48
  49                 wlan {
  50                         label = "ap121f:green:wlan";
  51                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  52                         linux,default-trigger = "phy0tpt";
  53                 };
  54         };
  55 };
  56
  57 &eth0 {
  58         status = "okay";
  59
  60         mtd-mac-address = <&art 0x0>;
  61
  62         gmac-config {
  63                 device = <&gmac>;
  64                 switch-phy-addr-swap = <0>;
  65                 switch-phy-swap = <0>;
  66         };
  67 };
  68
  69 &eth1 {
  70         status = "okay";
  71
  72         compatible = "syscon", "simple-mfd";
  73 };
  74
  75 &spi {
  76         status = "okay";
  77
  78         num-cs = <1>;
  79
  80         flash@0 {
  81                 compatible = "jedec,spi-nor";
  82                 reg = <0>;
  83                 spi-max-frequency = <25000000>;
  84
  85                 partitions {
  86                         compatible = "fixed-partitions";
  87                         #address-cells = <1>;
  88                         #size-cells = <1>;
  89
  90                         partition@0 {
  91                                 label = "u-boot";
  92                                 reg = <0x000000 0x030000>;
  93                                 read-only;
  94                         };
  95
  96                         partition@30000 {
  97                                 label = "u-boot-env";
  98                                 reg = <0x030000 0x010000>;
  99                         };
 100
 101                         art: partition@40000 {
 102                                 label = "art";
 103                                 reg = <0x040000 0x010000>;
 104                                 read-only;
 105                         };
 106
 107                         partition@50000 {
 108                                 compatible = "denx,uimage";
 109                                 label = "firmware";
 110                                 reg = <0x050000 0xfb0000>;
 111                         };
 112                 };
 113         };
 114 };
 115
 116 &uart {
 117         status = "okay";
 118 };
 119
 120 &usb {
 121         status = "okay";
 122         dr_mode = "host";
 123 };
 124
 125 &usb_phy {
 126         status = "okay";
 127 };
 128
 129 &wmac {
 130         status = "okay";
 131
 132         mtd-cal-data = <&art 0x1000>;
 133 };