target/linux/ath79/dts/qca9563_phicomm_k2t.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "Phicomm K2T";
  11         compatible = "phicomm,k2t";
  12
  13         aliases {
  14                 led-status = &status_red;
  15         };
  16
  17         chosen {
  18                 bootargs = "console=ttyS0,115200n8";
  19         };
  20
  21         leds {
  22                 compatible = "gpio-leds";
  23
  24                 status_blue {
  25                         label = "phicomm:blue:status";
  26                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  27                         default-state = "off";
  28                 };
  29
  30                 status_red: status_red {
  31                         label = "phicomm:red:status";
  32                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  33                         default-state = "off";
  34                 };
  35
  36                 status_yellow {
  37                         label = "phicomm:yellow:status";
  38                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  39                         default-state = "off";
  40                 };
  41         };
  42
  43         keys {
  44                 compatible = "gpio-keys-polled";
  45                 poll-interval = <20>;
  46
  47                 reset {
  48                         linux,code = <KEY_RESTART>;
  49                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  50                         debounce-interval = <60>;
  51                 };
  52         };
  53 };
  54
  55 &uart {
  56         status = "okay";
  57 };
  58
  59 &gpio {
  60         status = "okay";
  61 };
  62
  63 &pcie {
  64         status = "okay";
  65 };
  66
  67 &spi {
  68         num-cs = <1>;
  69
  70         status = "okay";
  71
  72         flash@0 {
  73                 compatible = "jedec,spi-nor";
  74                 reg = <0>;
  75                 spi-max-frequency = <25000000>;
  76
  77                 partitions {
  78                         compatible = "fixed-partitions";
  79                         #address-cells = <1>;
  80                         #size-cells = <1>;
  81
  82                         partition@0 {
  83                                 label = "u-boot";
  84                                 reg = <0x000000 0x30000>;
  85                                 read-only;
  86                         };
  87
  88                         partition@30000 {
  89                                 label = "config";
  90                                 reg = <0x030000 0x10000>;
  91                                 read-only;
  92                         };
  93
  94                         partition@40000 {
  95                                 label = "permanent";
  96                                 reg = <0x040000 0x50000>;
  97                                 read-only;
  98                         };
  99
 100                         partition@90000 {
 101                                 label = "firmware";
 102                                 reg = <0x090000 0xf60000>;
 103                         };
 104
 105                         art: partition@ff0000 {
 106                                 label = "art";
 107                                 reg = <0xff0000 0x010000>;
 108                                 read-only;
 109                         };
 110                 };
 111         };
 112 };
 113
 114 &mdio0 {
 115         status = "okay";
 116
 117         phy-mask = <0>;
 118
 119         phy0: ethernet-phy@0 {
 120                 reg = <0>;
 121                 phy-mode = "sgmii";
 122
 123                 qca,ar8327-initvals = <
 124                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 125                         0x10 0x81000080 /* POWER_ON_STRIP */
 126                         0x50 0xcc35cc35 /* LED_CTRL0 */
 127                         0x54 0xcb37cb37 /* LED_CTRL1 */
 128                         0x58 0x00000000 /* LED_CTRL2 */
 129                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 130                         0x7c 0x0000007e /* PORT0_STATUS */
 131                         >;
 132         };
 133 };
 134
 135 &eth0 {
 136         status = "okay";
 137
 138         pll-data = <0x03000101 0x00000101 0x00001919>;
 139
 140         phy-mode = "sgmii";
 141         phy-handle = <&phy0>;
 142 };
 143
 144 &wmac {
 145         status = "okay";
 146         mtd-cal-data = <&art 0x1000>;
 147 };