+++ /dev/null
-#
-# Copyright (C) 2009-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-include $(TOPDIR)/rules.mk
-
-ARCH:=arm
-BOARD:=ep93xx
-BOARDNAME:=Cirrus Logic EP93xx
-FEATURES:=squashfs ext4 targz usb display sound
-CPU_TYPE:=arm920t
-MAINTAINER:=Florian Fainelli <florian@openwrt.org>
-
-KERNEL_PATCHVER:=3.8
-
-DEVICE_TYPE:=developerboard
-
-include $(INCLUDE_DIR)/target.mk
-
-KERNELNAME:=uImage
-
-$(eval $(call BuildTarget))
+++ /dev/null
-::sysinit:/etc/init.d/rcS S boot
-::shutdown:/etc/init.d/rcS K shutdown
-tts/0::askfirst:/bin/ash --login
-ttyAM0::askfirst:/bin/ash --login
-tty1::askfirst:/bin/ash --login
+++ /dev/null
-#!/bin/sh
-# Copyright (C) 2010 OpenWrt.org
-
-. /lib/functions.sh
-
-set_ether_mac() {
- mac=$(sed -n 's/^Serial.* 000000/02/p' /proc/cpuinfo)
- ifconfig eth0 hw ether $mac
-}
-
-boot_hook_add preinit_main set_ether_mac
-
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_EP93XX=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USES_GETTIMEOFFSET=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_NR_BANKS=16
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_VIC=y
-CONFIG_ARM_VIC_NR=2
-# CONFIG_ARPD is not set
-CONFIG_ATAGS=y
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="console=ttyAM0,57600 init=/etc/preinit"
-CONFIG_CMDLINE_FROM_BOOTLOADER=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v4T=y
-CONFIG_CPU_ABRT_EV4T=y
-CONFIG_CPU_ARM920T=y
-CONFIG_CPU_CACHE_V4WT=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC7=y
-CONFIG_CRC_ITU_T=y
-CONFIG_CRUNCH=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_USER is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-CONFIG_EP93XX_EARLY_UART1=y
-# CONFIG_EP93XX_EARLY_UART2 is not set
-# CONFIG_EP93XX_EARLY_UART3 is not set
-CONFIG_EP93XX_ETH=y
-# CONFIG_EP93XX_PWM is not set
-CONFIG_EP93XX_SDCE0_PHYS_OFFSET=y
-# CONFIG_EP93XX_SDCE1_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE2_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET is not set
-CONFIG_EP93XX_SOC_COMMON=y
-CONFIG_EP93XX_WATCHDOG=y
-CONFIG_FRAME_POINTER=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_EP93XX=y
-CONFIG_GPIO_GENERIC=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HW_CONSOLE=y
-CONFIG_I2C=y
-CONFIG_I2C_ALGOBIT=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-# CONFIG_INPUT_MISC is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_WORK=y
-CONFIG_KTIME_SCALAR=y
-CONFIG_LEDS_GPIO_REGISTER=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_MACH_EDB9302A is not set
-# CONFIG_MACH_EDB9307A is not set
-# CONFIG_MACH_EDB9315A is not set
-CONFIG_MACH_SIM_ONE=y
-# CONFIG_MACH_SNAPPER_CL15 is not set
-# CONFIG_MACH_VISION_EP9307 is not set
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_SPI=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-CONFIG_MTD_CFI_STAA=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_RAM=y
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PAGE_OFFSET=0xC0000000
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERF_USE_VMALLOC=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_RCU_STALL_COMMON is not set
-# CONFIG_SCHED_HRTICK is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_EP93XX=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
-# CONFIG_TOUCHSCREEN_AUO_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_BU21013 is not set
-# CONFIG_TOUCHSCREEN_DYNAPRO is not set
-# CONFIG_TOUCHSCREEN_EP93XX is not set
-# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
-# CONFIG_TOUCHSCREEN_MAX11801 is not set
-# CONFIG_TOUCHSCREEN_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_ST1232 is not set
-# CONFIG_TOUCHSCREEN_TSC2005 is not set
-# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
-CONFIG_UID16=y
-CONFIG_UIDGID_CONVERTED=y
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-# CONFIG_USB_ARCH_HAS_EHCI is not set
-# CONFIG_USB_ARCH_HAS_XHCI is not set
-CONFIG_USB_SUPPORT=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VIDEO_OUTPUT_CONTROL=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_EP93XX=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USES_GETTIMEOFFSET=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_NR_BANKS=16
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_VIC=y
-CONFIG_ARM_VIC_NR=2
-CONFIG_ATAGS=y
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="console=ttyAM0,57600 init=/etc/preinit"
-CONFIG_CMDLINE_FROM_BOOTLOADER=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v4T=y
-CONFIG_CPU_ABRT_EV4T=y
-CONFIG_CPU_ARM920T=y
-CONFIG_CPU_CACHE_V4WT=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC7=y
-CONFIG_CRC_ITU_T=y
-CONFIG_CRUNCH=y
-CONFIG_DEBUG_LL_INCLUDE="debug/pl01x.S"
-# CONFIG_DEBUG_UART_8250 is not set
-CONFIG_DEBUG_UART_PHYS=0x808c0000
-CONFIG_DEBUG_UART_PL01X=y
-CONFIG_DEBUG_UART_VIRT=0xfedc0000
-# CONFIG_DEBUG_USER is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-CONFIG_EP93XX_ETH=y
-CONFIG_EP93XX_SDCE0_PHYS_OFFSET=y
-# CONFIG_EP93XX_SDCE1_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE2_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET is not set
-CONFIG_EP93XX_SOC_COMMON=y
-CONFIG_EP93XX_WATCHDOG=y
-CONFIG_FRAME_POINTER=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_EP93XX=y
-CONFIG_GPIO_GENERIC=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZ4=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HW_CONSOLE=y
-CONFIG_HZ_FIXED=0
-CONFIG_I2C=y
-CONFIG_I2C_ALGOBIT=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-# CONFIG_INPUT_MISC is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_IOMMU_HELPER=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_KTIME_SCALAR=y
-CONFIG_LEDS_GPIO_REGISTER=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_MACH_EDB9302A is not set
-# CONFIG_MACH_EDB9307A is not set
-# CONFIG_MACH_EDB9315A is not set
-CONFIG_MACH_SIM_ONE=y
-# CONFIG_MACH_SNAPPER_CL15 is not set
-# CONFIG_MACH_VISION_EP9307 is not set
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_SPI=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-CONFIG_MTD_CFI_STAA=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_RAM=y
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NO_BOOTMEM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PAGE_OFFSET=0xC0000000
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERF_USE_VMALLOC=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_RCU_STALL_COMMON is not set
-# CONFIG_SCHED_HRTICK is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SOC_BUS=y
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_EP93XX=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SWIOTLB=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
-# CONFIG_TOUCHSCREEN_AUO_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_BU21013 is not set
-# CONFIG_TOUCHSCREEN_CYTTSP4_CORE is not set
-# CONFIG_TOUCHSCREEN_DYNAPRO is not set
-# CONFIG_TOUCHSCREEN_EP93XX is not set
-# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
-# CONFIG_TOUCHSCREEN_MAX11801 is not set
-# CONFIG_TOUCHSCREEN_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_ST1232 is not set
-# CONFIG_TOUCHSCREEN_TSC2005 is not set
-# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
-CONFIG_UID16=y
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-CONFIG_USB_SUPPORT=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VIDEO_OUTPUT_CONTROL=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_EP93XX=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USES_GETTIMEOFFSET=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_NR_BANKS=16
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_VIC=y
-CONFIG_ARM_VIC_NR=2
-CONFIG_ATAGS=y
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="console=ttyAM0,57600 init=/etc/preinit"
-CONFIG_CMDLINE_FROM_BOOTLOADER=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v4T=y
-CONFIG_CPU_ABRT_EV4T=y
-CONFIG_CPU_ARM920T=y
-CONFIG_CPU_CACHE_V4WT=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC7=y
-CONFIG_CRC_ITU_T=y
-CONFIG_CRUNCH=y
-CONFIG_DEBUG_LL_INCLUDE="debug/pl01x.S"
-# CONFIG_DEBUG_UART_8250 is not set
-CONFIG_DEBUG_UART_PHYS=0x808c0000
-CONFIG_DEBUG_UART_PL01X=y
-CONFIG_DEBUG_UART_VIRT=0xfedc0000
-# CONFIG_DEBUG_USER is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-CONFIG_EP93XX_ETH=y
-CONFIG_EP93XX_SDCE0_PHYS_OFFSET=y
-# CONFIG_EP93XX_SDCE1_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE2_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET is not set
-CONFIG_EP93XX_SOC_COMMON=y
-CONFIG_EP93XX_WATCHDOG=y
-CONFIG_FRAME_POINTER=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_EP93XX=y
-CONFIG_GPIO_GENERIC=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZ4=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HW_CONSOLE=y
-CONFIG_HZ_FIXED=0
-CONFIG_I2C=y
-CONFIG_I2C_ALGOBIT=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-# CONFIG_INPUT_MISC is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_IOMMU_HELPER=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-CONFIG_KTIME_SCALAR=y
-CONFIG_LEDS_GPIO_REGISTER=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_MACH_EDB9302A is not set
-# CONFIG_MACH_EDB9307A is not set
-# CONFIG_MACH_EDB9315A is not set
-CONFIG_MACH_SIM_ONE=y
-# CONFIG_MACH_SNAPPER_CL15 is not set
-# CONFIG_MACH_VISION_EP9307 is not set
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_SPI=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-CONFIG_MTD_CFI_STAA=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_RAM=y
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NO_BOOTMEM=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PAGE_OFFSET=0xC0000000
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERF_USE_VMALLOC=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_RCU_STALL_COMMON is not set
-# CONFIG_SCHED_HRTICK is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SOC_BUS=y
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_EP93XX=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SWIOTLB=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
-# CONFIG_TOUCHSCREEN_AUO_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_BU21013 is not set
-# CONFIG_TOUCHSCREEN_CYTTSP4_CORE is not set
-# CONFIG_TOUCHSCREEN_DYNAPRO is not set
-# CONFIG_TOUCHSCREEN_EP93XX is not set
-# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
-# CONFIG_TOUCHSCREEN_MAX11801 is not set
-# CONFIG_TOUCHSCREEN_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_ST1232 is not set
-# CONFIG_TOUCHSCREEN_TSC2005 is not set
-# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
-CONFIG_UID16=y
-CONFIG_UNCOMPRESS_INCLUDE="mach/uncompress.h"
-CONFIG_USB_SUPPORT=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VIDEO_OUTPUT_CONTROL=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_EP93XX=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
-# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USES_GETTIMEOFFSET=y
-# CONFIG_ARCH_VT8500_SINGLE is not set
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARM=y
-CONFIG_ARM_AMBA=y
-# CONFIG_ARM_CPU_SUSPEND is not set
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_NR_BANKS=16
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-# CONFIG_ARM_SP805_WATCHDOG is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_VIC=y
-CONFIG_ARM_VIC_NR=2
-# CONFIG_ARPD is not set
-CONFIG_ATAGS=y
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CACHE_L2X0 is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="console=ttyAM0,57600 init=/etc/preinit"
-CONFIG_CMDLINE_FROM_BOOTLOADER=y
-CONFIG_CONSOLE_TRANSLATIONS=y
-CONFIG_CPU_32v4T=y
-CONFIG_CPU_ABRT_EV4T=y
-CONFIG_CPU_ARM920T=y
-CONFIG_CPU_CACHE_V4WT=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRC7=y
-CONFIG_CRC_ITU_T=y
-CONFIG_CRUNCH=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_USER is not set
-CONFIG_DUMMY_CONSOLE=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-CONFIG_EP93XX_EARLY_UART1=y
-# CONFIG_EP93XX_EARLY_UART2 is not set
-# CONFIG_EP93XX_EARLY_UART3 is not set
-CONFIG_EP93XX_ETH=y
-# CONFIG_EP93XX_PWM is not set
-CONFIG_EP93XX_SDCE0_PHYS_OFFSET=y
-# CONFIG_EP93XX_SDCE1_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE2_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET is not set
-# CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET is not set
-CONFIG_EP93XX_SOC_COMMON=y
-CONFIG_EP93XX_WATCHDOG=y
-CONFIG_FRAME_POINTER=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_EP93XX=y
-CONFIG_GPIO_GENERIC=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_AOUT=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IRQ_WORK=y
-CONFIG_HAVE_KERNEL_GZIP=y
-CONFIG_HAVE_KERNEL_LZMA=y
-CONFIG_HAVE_KERNEL_LZO=y
-CONFIG_HAVE_KERNEL_XZ=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HW_CONSOLE=y
-CONFIG_I2C=y
-CONFIG_I2C_ALGOBIT=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_INPUT=y
-# CONFIG_INPUT_MISC is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_KTIME_SCALAR=y
-CONFIG_LEDS_GPIO_REGISTER=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_MACH_EDB9302A is not set
-# CONFIG_MACH_EDB9307A is not set
-# CONFIG_MACH_EDB9315A is not set
-CONFIG_MACH_SIM_ONE=y
-# CONFIG_MACH_SNAPPER_CL15 is not set
-# CONFIG_MACH_VISION_EP9307 is not set
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_SPI=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-CONFIG_MTD_CFI_STAA=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_RAM=y
-CONFIG_MULTI_IRQ_HANDLER=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_MACH_MEMORY_H=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PAGE_OFFSET=0xC0000000
-# CONFIG_PCI_SYSCALL is not set
-CONFIG_PERCPU_RWSEM=y
-CONFIG_PERF_USE_VMALLOC=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_AMBA_PL010=y
-CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
-# CONFIG_SERIAL_AMBA_PL011 is not set
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_EP93XX=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TICK_CPU_ACCOUNTING=y
-# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
-# CONFIG_TOUCHSCREEN_AUO_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_BU21013 is not set
-# CONFIG_TOUCHSCREEN_DYNAPRO is not set
-# CONFIG_TOUCHSCREEN_EP93XX is not set
-# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set
-# CONFIG_TOUCHSCREEN_MAX11801 is not set
-# CONFIG_TOUCHSCREEN_PIXCIR is not set
-# CONFIG_TOUCHSCREEN_ST1232 is not set
-# CONFIG_TOUCHSCREEN_TSC2005 is not set
-# CONFIG_TOUCHSCREEN_TSC_SERIO is not set
-CONFIG_UID16=y
-CONFIG_UIDGID_CONVERTED=y
-# CONFIG_USB_ARCH_HAS_EHCI is not set
-# CONFIG_USB_ARCH_HAS_XHCI is not set
-CONFIG_USB_SUPPORT=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_VIDEO_OUTPUT_CONTROL=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
-#
-# Copyright (C) 2009-2010 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-include $(TOPDIR)/rules.mk
-include $(INCLUDE_DIR)/image.mk
-
-UIMAGE:=$(BIN_DIR)/$(IMG_PREFIX)-uImage
-fs_squash:=squashfs-only
-fs_all:=all
-fs_4k:=4k
-fs_64k:=64k
-fs_128k:=128k
-
-define Image/BuildKernel
- cp $(KDIR)/uImage $(UIMAGE)
-ifeq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),y)
- cp $(KDIR)/uImage-initramfs $(UIMAGE)-initramfs
-endif
-endef
-
-define Image/Build/jffs2-64k
- dd if=$(KDIR)/root.$(1) of=$(BIN_DIR)/$(IMG_PREFIX)-$(1).img bs=64k conv=sync
-endef
-
-define Image/Build/jffs2-128k
- dd if=$(KDIR)/root.$(1) of=$(BIN_DIR)/$(IMG_PREFIX)-$(1).img bs=128k conv=sync
-endef
-
-define Image/Build/squashfs
- $(call prepare_generic_squashfs,$(KDIR)/root.squashfs)
- dd if=$(KDIR)/root.$(1) of=$(BIN_DIR)/$(IMG_PREFIX)-$(1).img bs=128k conv=sync
-endef
-
-define Image/Build
- $(call Image/Build/$(1),$(1))
-endef
-
-$(eval $(call BuildImage))
+++ /dev/null
-#
-# Copyright (C) 2011-2015 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-define KernelPackage/fb-ep93xx
- SUBMENU:=$(VIDEO_MENU)
- TITLE:=EP93xx framebuffer support
- DEPENDS:=@TARGET_ep93xx +kmod-fb +kmod-fb-cfb-fillrect \
- +kmod-fb-cfb-copyarea +kmod-fb-cfb-imgblt
- KCONFIG:=CONFIG_FB_EP93XX
- FILES:=$(LINUX_DIR)/drivers/video/ep93xx-fb.ko
- AUTOLOAD:=$(call AutoLoad,51,ep93xx-fb)
-endef
-
-define KernelPackage/fb-ep93xx/description
- EP93xx framebuffer support
-endef
-
-$(eval $(call KernelPackage,fb-ep93xx))
-
-define KernelPackage/input-keyboard-ep93xx
- SUBMENU:=$(OTHER_MENU)
- TITLE:=EP93xx Matrix Keypad support
- DEPENDS:=@TARGET_ep93xx +kmod-input-matrixkmap
- KCONFIG:= \
- CONFIG_KEYBOARD_EP93XX \
- CONFIG_INPUT_KEYBOARD=y
- FILES:=$(LINUX_DIR)/drivers/input/keyboard/ep93xx_keypad.ko
- AUTOLOAD:=$(call AutoLoad,62,ep93xx_keypad)
- $(call AddDepends/input)
-endef
-
-define KernelPackage/input-keyboard-ep93xx/description
- EP93xx Matrix Keypad support
-endef
-
-$(eval $(call KernelPackage,input-keyboard-ep93xx))
-
-define KernelPackage/sound-soc-ep93xx
- SUBMENU:=$(SOUND_MENU)
- TITLE:=EP93xx SoC sound support
- DEPENDS:=@TARGET_ep93xx +kmod-sound-core +kmod-sound-soc-core
- KCONFIG:=CONFIG_SND_EP93XX_SOC
- FILES:=$(LINUX_DIR)/sound/soc/cirrus/snd-soc-ep93xx.ko
- AUTOLOAD:=$(call AutoLoad,57,snd-soc-ep93xx)
-endef
-
-define KernelPackage/sound-soc-ep93xx/description
- EP93xx SoC sound support
-endef
-
-$(eval $(call KernelPackage,sound-soc-ep93xx))
-
-# Must be loaded prior to sound-soc-ac97 because it exports
-# soc_ac97_ops
-define KernelPackage/sound-soc-ep93xx-ac97
- SUBMENU:=$(SOUND_MENU)
- TITLE:=EP93xx SoC AC97 support
- DEPENDS:=@TARGET_ep93xx +kmod-sound-soc-core
- KCONFIG:=CONFIG_SND_EP93XX_SOC_AC97
- FILES:=$(LINUX_DIR)/sound/soc/cirrus/snd-soc-ep93xx-ac97.ko
- AUTOLOAD:=$(call AutoLoad,56,snd-soc-ep93xx-ac97)
-endef
-
-define KernelPackage/sound-soc-ep93xx-ac97/description
- EP93xx SoC AC97 support
-endef
-
-$(eval $(call KernelPackage,sound-soc-ep93xx-ac97))
-
-define KernelPackage/sound-soc-ep93xx-simone
- SUBMENU:=$(SOUND_MENU)
- TITLE:=Sim.One EP93xx Soc sound support
- DEPENDS:=@TARGET_ep93xx +kmod-sound-soc-core
- KCONFIG:=CONFIG_SND_EP93XX_SOC_SIMONE
- FILES:=$(LINUX_DIR)/sound/soc/cirrus/snd-soc-simone.ko
- AUTOLOAD:=$(call AutoLoad,59,snd-soc-ep93xx)
-endef
-
-define KernelPackage/sound-soc-ep93xx-simone/description
- SimpleMachines Sim.One sound support
-endef
-
-$(eval $(call KernelPackage,sound-soc-ep93xx-simone))
-
-define KernelPackage/touchscreen-ep93xx
- SUBMENU:=$(OTHER_MENU)
- TITLE:=EP93xx input touchscreen support
- DEPENDS:=@TARGET_ep93xx
- KCONFIG:=CONFIG_TOUCHSCREEN_EP93XX
- FILES:=$(LINUX_DIR)/drivers/input/touchscreen/ep93xx_ts.ko
- AUTOLOAD:=$(call AutoLoad,51,ep93xx_ts)
-endef
-
-define KernelPackage/touchscreen-ep93xx/description
- EP93xx SoC input touchscreen support
-endef
-
-$(eval $(call KernelPackage,touchscreen-ep93xx))
-
+++ /dev/null
-This patch puts the EP93xx chip revision and unique ID into /proc/cpuinfo.
-This is necessary to be able to set a unique MAC address for DHCP purposes
-by adding a line to /etc/network/interfaces:
-
-# Generate a unique locally-assigned MAC address from the CPU serial number
-pre-up ifconfig eth0 hw ether `sed -n 's/^Serial.* 000000/02/p' /proc/cpuinfo`
-
-It uses the chip revision reading code in the ep93xx-chip-revision patch.
-
-Really, this is wrong, since /proc/cpuinfo should report the revision and
-serial number of the ARM920T processor, while these are the rev and serial
-of the EP93xx SoC. In a future kernel (>2.6.34) there may be a new file
-/proc/socinfo for this information.
-
- -martinwguy 14 May 2010
-
---- a/arch/arm/kernel/setup.c
-+++ b/arch/arm/kernel/setup.c
-@@ -56,6 +56,12 @@
- #include <asm/memblock.h>
- #include <asm/virt.h>
-
-+#if defined(CONFIG_ARCH_EP93XX)
-+#include <asm/io.h>
-+#include <mach/platform.h>
-+#include <mach/ep93xx-regs.h>
-+#endif
-+
- #include "atags.h"
-
-
-@@ -953,9 +959,16 @@ static int c_show(struct seq_file *m, vo
- }
-
- seq_printf(m, "Hardware\t: %s\n", machine_name);
-+#if defined(CONFIG_ARCH_EP93XX)
-+ seq_printf(m, "Revision\t: %04x\n",
-+ ep93xx_chip_revision());
-+ seq_printf(m, "Serial\t\t: %016x\n",
-+ *((unsigned int *)EP93XX_SECURITY_UNIQID));
-+#else
- seq_printf(m, "Revision\t: %04x\n", system_rev);
- seq_printf(m, "Serial\t\t: %08x%08x\n",
- system_serial_high, system_serial_low);
-+#endif
-
- return 0;
- }
---- a/arch/arm/mach-ep93xx/soc.h
-+++ b/arch/arm/mach-ep93xx/soc.h
-@@ -82,8 +82,6 @@
- #define EP93XX_I2S_PHYS_BASE EP93XX_APB_PHYS(0x00020000)
- #define EP93XX_I2S_BASE EP93XX_APB_IOMEM(0x00020000)
-
--#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
--
- #define EP93XX_AAC_PHYS_BASE EP93XX_APB_PHYS(0x00080000)
- #define EP93XX_AAC_BASE EP93XX_APB_IOMEM(0x00080000)
-
---- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-@@ -38,4 +38,8 @@
- #define EP93XX_UART3_PHYS_BASE EP93XX_APB_PHYS(0x000e0000)
- #define EP93XX_UART3_BASE EP93XX_APB_IOMEM(0x000e0000)
-
-+#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
-+#define EP93XX_SECURITY_REG(x) (EP93XX_SECURITY_BASE + (x))
-+#define EP93XX_SECURITY_UNIQID EP93XX_SECURITY_REG(0x2440)
-+
- #endif
+++ /dev/null
----
- arch/arm/mach-ep93xx/include/mach/hardware.h | 1
- arch/arm/mach-ep93xx/include/mach/regs_touch.h | 95 ++
- drivers/input/touchscreen/Kconfig | 5
- drivers/input/touchscreen/Makefile | 1
- drivers/input/touchscreen/ep93xx_ts.c | 1117 +++++++++++++++++++++++++
- drivers/input/touchscreen/ep93xx_ts.h | 53 +
- 6 files changed, 1272 insertions(+)
-
---- a/drivers/input/touchscreen/Kconfig
-+++ b/drivers/input/touchscreen/Kconfig
-@@ -235,6 +235,15 @@ config TOUCHSCREEN_EGALAX
- To compile this driver as a module, choose M here: the
- module will be called egalax_ts.
-
-+config TOUCHSCREEN_EP93XX
-+ tristate "EP93xx Touchscreen"
-+ depends on ARM && INPUT && ARCH_EP93XX
-+ help
-+ Say Y here to enable support for EP93xx touch screen.
-+
-+ To compile this driver as a module, choose M here:
-+ the module will be called ep93xx_ts.
-+
- config TOUCHSCREEN_FUJITSU
- tristate "Fujitsu serial touchscreen"
- select SERIO
---- a/drivers/input/touchscreen/Makefile
-+++ b/drivers/input/touchscreen/Makefile
-@@ -29,6 +29,7 @@ obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunz
- obj-$(CONFIG_TOUCHSCREEN_EETI) += eeti_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
- obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o
-+obj-$(CONFIG_TOUCHSCREEN_EP93XX) += ep93xx_ts.o
- obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
- obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
---- /dev/null
-+++ b/drivers/input/touchscreen/ep93xx_ts.c
-@@ -0,0 +1,1022 @@
-+/*
-+ * linux/drivers/input/touchscreen/ep93xx_ts.c
-+ *
-+ * Copyright (C) 2003-2004 Cirrus Corp.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/delay.h>
-+#include <linux/wait.h>
-+#include <linux/fs.h>
-+#include <linux/sched.h>
-+#include <linux/poll.h>
-+#include <linux/miscdevice.h>
-+#include <linux/init.h>
-+#include <linux/compiler.h>
-+#include <linux/timer.h>
-+#include <linux/interrupt.h>
-+#include <linux/syscalls.h>
-+#include <linux/input.h>
-+#include <linux/semaphore.h>
-+#include <asm/irq.h>
-+#include <mach/hardware.h>
-+#include <asm/io.h>
-+#include "../../../arch/arm/mach-ep93xx/soc.h"
-+
-+/* This stuff should be in ep93xx-regs.h */
-+#define EP93XX_TOUCHSCREEN_REG(x) (EP93XX_TOUCHSCREEN_BASE + (x))
-+/* R/W touchscreen controller setup control register. */
-+#define EP93XX_TOUCHSCREEN_SETUP EP93XX_TOUCHSCREEN_REG(0x00)
-+/* R/W touchscreen controller max/min register. */
-+#define EP93XX_TOUCHSCREEN_XYMAXMIN EP93XX_TOUCHSCREEN_REG(0x04)
-+/* R touchscreen controller result register. */
-+#define EP93XX_TOUCHSCREEN_XYRESULT EP93XX_TOUCHSCREEN_REG(0x08)
-+/* LOCKED R/W touchscreen Switch Matrix control register. */
-+#define EP93XX_TOUCHSCREEN_DISCHARGE EP93XX_TOUCHSCREEN_REG(0x0C)
-+#define EP93XX_TOUCHSCREEN_XSAMPLE EP93XX_TOUCHSCREEN_REG(0x10)
-+#define EP93XX_TOUCHSCREEN_YSAMPLE EP93XX_TOUCHSCREEN_REG(0x14)
-+#define EP93XX_TOUCHSCREEN_DIRECT EP93XX_TOUCHSCREEN_REG(0x18)
-+#define EP93XX_TOUCHSCREEN_DETECT EP93XX_TOUCHSCREEN_REG(0x1C)
-+/* NA R/W touchscreen software lock register. */
-+#define EP93XX_TOUCHSCREEN_SWLOCK EP93XX_TOUCHSCREEN_REG(0x20)
-+/* R/W touchscreen setup control register #2. */
-+#define EP93XX_TOUCHSCREEN_SETUP2 EP93XX_TOUCHSCREEN_REG(0x24)
-+
-+/* These are duplicated in mach-ep93xx/core.c */
-+#define EP93XX_TIMER_REG(x) (EP93XX_TIMER_BASE + (x))
-+#define EP93XX_TIMER2_LOAD EP93XX_TIMER_REG(0x20)
-+#define EP93XX_TIMER2_VALUE EP93XX_TIMER_REG(0x24)
-+#define EP93XX_TIMER2_CONTROL EP93XX_TIMER_REG(0x28)
-+#define EP93XX_TIMER2_CLEAR EP93XX_TIMER_REG(0x2c)
-+
-+/*
-+ * Register bit definitions
-+ */
-+#define TSSETUP_SDLY_MASK 0x000003FF
-+#define TSSETUP_SDLY_SHIFT 0
-+#define TSSETUP_NSMP_4 0x00000000
-+#define TSSETUP_NSMP_8 0x00000400
-+#define TSSETUP_NSMP_16 0x00000800
-+#define TSSETUP_NSMP_32 0x00000C00
-+#define TSSETUP_NSMP_MASK 0x00000C00
-+#define TSSETUP_DEV_4 0x00000000
-+#define TSSETUP_DEV_8 0x00001000
-+#define TSSETUP_DEV_12 0x00002000
-+#define TSSETUP_DEV_16 0x00003000
-+#define TSSETUP_DEV_24 0x00004000
-+#define TSSETUP_DEV_32 0x00005000
-+#define TSSETUP_DEV_64 0x00006000
-+#define TSSETUP_DEV_128 0x00007000
-+#define TSSETUP_ENABLE 0x00008000
-+#define TSSETUP_DLY_MASK 0x03FF0000
-+#define TSSETUP_DLY_SHIFT 16
-+#define TSSETUP_TDTCT 0x80000000
-+
-+#define TSMAXMIN_XMIN_MASK 0x000000FF
-+#define TSMAXMIN_XMIN_SHIFT 0
-+#define TSMAXMIN_YMIN_MASK 0x0000FF00
-+#define TSMAXMIN_YMIN_SHIFT 8
-+#define TSMAXMIN_XMAX_MASK 0x00FF0000
-+#define TSMAXMIN_XMAX_SHIFT 16
-+#define TSMAXMIN_YMAX_MASK 0xFF000000
-+#define TSMAXMIN_YMAX_SHIFT 24
-+
-+#define TSXYRESULT_X_MASK 0x00000FFF
-+#define TSXYRESULT_X_SHIFT 0
-+#define TSXYRESULT_AD_MASK 0x0000FFFF
-+#define TSXYRESULT_AD_SHIFT 0
-+#define TSXYRESULT_Y_MASK 0x0FFF0000
-+#define TSXYRESULT_Y_SHIFT 16
-+#define TSXYRESULT_SDR 0x80000000
-+
-+#define TSX_SAMPLE_MASK 0x00003FFF
-+#define TSX_SAMPLE_SHIFT 0x00
-+#define TSY_SAMPLE_MASK 0x3FFF0000
-+#define TSY_SAMPLE_SHIFT 0x10
-+
-+#define TSSETUP2_TINT 0x00000001
-+#define TSSETUP2_NICOR 0x00000002
-+#define TSSETUP2_PINT 0x00000004
-+#define TSSETUP2_PENSTS 0x00000008
-+#define TSSETUP2_PINTEN 0x00000010
-+#define TSSETUP2_DEVINT 0x00000020
-+#define TSSETUP2_DINTEN 0x00000040
-+#define TSSETUP2_DTMEN 0x00000080
-+#define TSSETUP2_DISDEV 0x00000100
-+#define TSSETUP2_NSIGND 0x00000200
-+#define TSSETUP2_S28EN 0x00000400
-+#define TSSETUP2_RINTEN 0x00000800
-+
-+#define TSXYRESULT_SDR 0x80000000
-+
-+/*
-+ * These are used as trigger levels to know when we have pen up/down.
-+ * The rules:
-+ * 1. TS_HEAVY_INV_PRESSURE < TS_LIGHT_INV_PRESSURE because these
-+ * are Inverse pressure.
-+ * 2. Any touch lighter than TS_LIGHT_INV_PRESSURE is a pen up.
-+ * 3. Any touch heavier than TS_HEAVY_INV_PRESSURE is a pen down.
-+ */
-+#define TS_HEAVY_INV_PRESSURE 0xFE0 /* C00 */
-+#define TS_LIGHT_INV_PRESSURE 0xFFF /* e00 */
-+
-+/*
-+ * If the x, y, or inverse pressure changes more than these values
-+ * between two succeeding points, the point is not reported.
-+ */
-+#define TS_MAX_VALID_XY_CHANGE 0x300
-+#define TS_MAX_VALID_PRESSURE_CHANGE 0x100
-+
-+/*
-+ * This is the minimum Z1 Value that is valid.
-+ */
-+#define MIN_Z1_VALUE 0x50
-+
-+/*
-+ * Settling delay for taking each ADC measurement. Increase this
-+ * if ts is jittery.
-+ */
-+#define EP93XX_TS_ADC_DELAY_USEC 2000
-+
-+/*
-+ * Delay between TS points.
-+ */
-+#define EP93XX_TS_PER_POINT_DELAY_USEC 10000
-+
-+/*
-+ * A few more macros...
-+ */
-+#define TSSETUP_DEFAULT (TSSETUP_NSMP_32 | TSSETUP_DEV_64 | \
-+ ((128<<TSSETUP_SDLY_SHIFT) & TSSETUP_SDLY_MASK) | \
-+ ((128<<TSSETUP_DLY_SHIFT) & TSSETUP_DLY_MASK))
-+
-+#define TSSETUP2_DEFAULT (TSSETUP2_NSIGND)
-+
-+/*
-+ * For now, we use one of the minor numbers from the local/experimental
-+ * range.
-+ */
-+#define EP93XX_TS_MINOR 240
-+
-+/*
-+ * Static Declarations
-+ */
-+static unsigned int guiLastX, guiLastY;
-+static unsigned int guiLastInvPressure;
-+
-+struct TouchScreenSample
-+{
-+ int currentX;
-+ int currentY;
-+ int currentButton;
-+ int currentPressure;
-+ struct timeval currentTime;
-+};
-+
-+/*
-+ * This must match the structure in tslib.
-+ */
-+struct ts_sample {
-+ int x;
-+ int y;
-+ unsigned int pressure;
-+ struct timeval tv;
-+};
-+
-+static struct TouchScreenSample gSample;
-+static int bFreshTouchData;
-+static int bCurrentPenDown;
-+
-+static DECLARE_WAIT_QUEUE_HEAD(queue);
-+static DEFINE_SEMAPHORE(open_sem);
-+static DEFINE_SPINLOCK(event_buffer_lock);
-+static struct fasync_struct *ep93xx_fasync;
-+
-+/*
-+ * Typedef Declarations
-+ */
-+typedef enum {
-+ TS_MODE_UN_INITIALIZED,
-+ TS_MODE_HARDWARE_SCAN,
-+ TS_MODE_SOFT_SCAN
-+} ts_mode_t;
-+
-+static ts_mode_t gScanningMode;
-+
-+typedef enum{
-+ TS_STATE_STOPPED = 0,
-+ TS_STATE_Z1,
-+ TS_STATE_Z2,
-+ TS_STATE_Y,
-+ TS_STATE_X,
-+ TS_STATE_DONE
-+} ts_states_t;
-+
-+typedef struct
-+{
-+ unsigned int uiX;
-+ unsigned int uiY;
-+ unsigned int uiZ1;
-+ unsigned int uiZ2;
-+ ts_states_t state;
-+} ts_struct_t;
-+
-+static ts_struct_t sTouch;
-+
-+/*
-+ * From the spec, here's how to set up the touch screen's switch registers.
-+ */
-+typedef struct
-+{
-+ unsigned int uiDetect;
-+ unsigned int uiDischarge;
-+ unsigned int uiXSample;
-+ unsigned int uiYSample;
-+ unsigned int uiSwitchZ1;
-+ unsigned int uiSwitchZ2;
-+}SwitchStructType;
-+
-+/*
-+ * Here's the switch settings for a 4-wire touchscreen. See the spec
-+ * for how to handle a 4, 7, or 8-wire.
-+ */
-+const static SwitchStructType sSwitchSettings =
-+/* s28en=0 */
-+/* TSDetect TSDischarge TSXSample TSYSample SwitchZ1 SwitchZ2 */
-+ {0x00403604, 0x0007fe04, 0x00081604, 0x00104601, 0x00101601, 0x00101608};
-+
-+/*
-+ * Function declarations
-+ */
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch);
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id);
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id);
-+static void ee93xx_ts_evt_add(int button, int dX, int dY, int Pressure);
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf,
-+ size_t count, loff_t *l);
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait);
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp);
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on);
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp);
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer,
-+ size_t count, loff_t *ppos);
-+static void ep93xx_ts_setup(void);
-+static void ep93xx_ts_shutdown(void);
-+int __init ep93xx_ts_init(void);
-+void __exit ep93xx_ts_exit(void);
-+static unsigned int CalculateInvPressure(void);
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff);
-+static void TS_Soft_Scan_Mode(void);
-+static void TS_Hardware_Scan_Mode(void);
-+static void ProcessPointData(void);
-+static void Set_Timer2_uSec(unsigned int Delay_mSec);
-+static void Stop_Timer2(void);
-+
-+/*
-+ * ep93xx_ts_isr
-+ */
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id)
-+{
-+ /*
-+ * Note that we don't clear the interrupt here. The interrupt
-+ * gets cleared in TS_Soft_Scan_Mode when the TS ENABLE
-+ * bit is cleared.
-+ */
-+
-+ /*
-+ * Set the ts to manual polling mode and schedule a callback.
-+ * That way we can return from the isr in a reasonable amount of
-+ * time and process the touch in the callback after a brief delay.
-+ */
-+ TS_Soft_Scan_Mode();
-+
-+ return(IRQ_HANDLED);
-+}
-+
-+/*
-+ * Save the current ts 'event' in an atomic fashion.
-+ */
-+static void ee93xx_ts_evt_add(int buttons, int iX, int iY, int iPressure)
-+{
-+ /*
-+ * Note the event, but use spinlocks to keep it from getting
-+ * halfway read if we get interrupted.
-+ */
-+
-+ spin_lock(&event_buffer_lock);
-+
-+ gSample.currentX = iX;
-+ gSample.currentY = iY;
-+ gSample.currentButton = buttons;
-+ gSample.currentPressure = iPressure;
-+ bFreshTouchData = 1;
-+ do_gettimeofday(&gSample.currentTime);
-+
-+ spin_unlock(&event_buffer_lock);
-+
-+ kill_fasync(&ep93xx_fasync, SIGIO, POLL_IN);
-+ wake_up_interruptible(&queue);
-+}
-+
-+
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf, size_t count, loff_t *l)
-+{
-+ unsigned short data[3];
-+ struct ts_sample ts_data;
-+ int iReturn = -EFAULT;
-+
-+ if (!bFreshTouchData)
-+ {
-+ iReturn = 0;
-+ }
-+ else if (count == sizeof(data))
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ data[0] = gSample.currentX;
-+ data[1] = gSample.currentY;
-+ data[2] = gSample.currentButton;
-+
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, data, sizeof data))
-+ return -EFAULT;
-+
-+ count -= sizeof(data);
-+
-+ /* return the # of bytes that got read */
-+ iReturn = sizeof(data) ;
-+ }
-+ else if (count == sizeof(struct ts_sample) )
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ ts_data.x = gSample.currentX;
-+ ts_data.y = gSample.currentY;
-+ ts_data.pressure = gSample.currentPressure;
-+ ts_data.tv = gSample.currentTime;
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, &ts_data, sizeof(struct ts_sample)))
-+ {
-+ iReturn = -EFAULT;
-+ }
-+ else
-+ {
-+ count -= sizeof(ts_data);
-+ iReturn = sizeof(ts_data);
-+ }
-+ }
-+
-+ return iReturn;
-+}
-+
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait)
-+{
-+ poll_wait(filp, &queue, wait);
-+
-+ if (bFreshTouchData)
-+ {
-+ return POLLIN | POLLRDNORM;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp)
-+{
-+ if (down_trylock(&open_sem))
-+ {
-+ return -EBUSY;
-+ }
-+
-+ ep93xx_ts_setup();
-+
-+ return 0;
-+}
-+
-+/*
-+ * Asynchronous I/O support.
-+ */
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on)
-+{
-+ int retval;
-+
-+ retval = fasync_helper(fd, filp, on, &ep93xx_fasync);
-+ if (retval < 0)
-+ {
-+ return retval;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp)
-+{
-+ Stop_Timer2();
-+
-+ /*
-+ * Call our async I/O support to request that this file
-+ * cease to be used for async I/O.
-+ */
-+ ep93xx_ts_fasync(-1, filp, 0);
-+
-+ ep93xx_ts_shutdown();
-+
-+ up(&open_sem);
-+
-+ return 0;
-+}
-+
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer, size_t count,
-+ loff_t *ppos)
-+{
-+ return -EINVAL;
-+}
-+
-+
-+static int ep93xx_ts_ioctl(struct inode *inode, struct file *file, uint command, ulong u)
-+{
-+ static const int version = EV_VERSION;
-+ static const u_int32_t bit =(1 << EV_ABS);
-+ static const u_int32_t absbit = (1 << ABS_X) | (1 << ABS_Y) | (1 << ABS_PRESSURE);
-+ int iReturn ;
-+ int i = 0;
-+
-+ switch(command)
-+ {
-+ case EVIOCGVERSION:
-+ i = copy_to_user((void __user *)u, (void *)version, sizeof(version));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(0,sizeof(u_int32_t) * 8) :
-+ i = copy_to_user((void __user *)u, (void *)bit, sizeof(bit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(EV_ABS, sizeof(absbit) * 8):
-+ i = copy_to_user((void __user *)u, (void *)absbit, sizeof(absbit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+ default:
-+ iReturn = -1;
-+ break;
-+ }
-+
-+ return iReturn;
-+}
-+
-+static struct file_operations ep93xx_ts_fops = {
-+ owner: THIS_MODULE,
-+ read: ep93xx_ts_read,
-+ write: ep93xx_ts_write,
-+ poll: ep93xx_ts_poll,
-+ open: ep93xx_ts_open,
-+ unlocked_ioctl: ep93xx_ts_ioctl,
-+ release: ep93xx_ts_release,
-+ fasync: ep93xx_ts_fasync,
-+};
-+
-+static struct miscdevice ep93xx_ts_miscdev =
-+{
-+ EP93XX_TS_MINOR,
-+ "ep93xx_ts",
-+ &ep93xx_ts_fops
-+};
-+
-+void ep93xx_ts_setup(void)
-+{
-+ unsigned int uiKTDIV, uiTSXYMaxMin;
-+
-+ /*
-+ * Set the TSEN bit in KTDIV so that we are enabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV |= EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+ /*
-+ * Program the EP93XX_TOUCHSCREEN_SETUP and TSSetup2 registers.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Set the the touch settings.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DISCHARGE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ1, EP93XX_TOUCHSCREEN_XSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ2, EP93XX_TOUCHSCREEN_YSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDetect, EP93XX_TOUCHSCREEN_DETECT);
-+
-+ /*
-+ * X,YMin set to 0x40 = have to drag that many pixels for a new irq.
-+ * X,YMax set to 0x40 = 1024 pixels is the maximum movement within the
-+ * time scan limit.
-+ */
-+ uiTSXYMaxMin = (50 << TSMAXMIN_XMIN_SHIFT) & TSMAXMIN_XMIN_MASK;
-+ uiTSXYMaxMin |= (50 << TSMAXMIN_YMIN_SHIFT) & TSMAXMIN_YMIN_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_XMAX_SHIFT) & TSMAXMIN_XMAX_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_YMAX_SHIFT) & TSMAXMIN_YMAX_MASK;
-+ __raw_writel(uiTSXYMaxMin, EP93XX_TOUCHSCREEN_XYMAXMIN);
-+
-+ bCurrentPenDown = 0;
-+ bFreshTouchData = 0;
-+ guiLastX = 0;
-+ guiLastY = 0;
-+ guiLastInvPressure = 0xffffff;
-+
-+ /*
-+ * Enable the touch screen scanning engine.
-+ */
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+/*
-+ * ep93xx_ts_shutdown
-+ *
-+ */
-+static void
-+ep93xx_ts_shutdown(void)
-+{
-+ unsigned int uiKTDIV;
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Disable the scanning engine.
-+ */
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Clear the TSEN bit in KTDIV so that we are disabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV &= ~EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+} /* ep93xx_ts_shutdown */
-+
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id)
-+{
-+ switch(sTouch.state)
-+ {
-+ case TS_STATE_STOPPED:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+
-+ /*
-+ * Get the Z1 value for pressure measurement and set up
-+ * the switch register for getting the Z2 measurement.
-+ */
-+ case TS_STATE_Z1:
-+ Set_Timer2_uSec(EP93XX_TS_ADC_DELAY_USEC);
-+ sTouch.uiZ1 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ2);
-+ sTouch.state = TS_STATE_Z2;
-+ break;
-+
-+ /*
-+ * Get the Z2 value for pressure measurement and set up
-+ * the switch register for getting the Y measurement.
-+ */
-+ case TS_STATE_Z2:
-+ sTouch.uiZ2 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiYSample);
-+ sTouch.state = TS_STATE_Y;
-+ break;
-+
-+ /*
-+ * Get the Y value and set up the switch register for
-+ * getting the X measurement.
-+ */
-+ case TS_STATE_Y:
-+ sTouch.uiY = ADCGetData(4, 20);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiXSample);
-+ sTouch.state = TS_STATE_X;
-+ break;
-+
-+ /*
-+ * Read the X value. This is the last of the 4 adc values
-+ * we need so we continue on to process the data.
-+ */
-+ case TS_STATE_X:
-+ Stop_Timer2();
-+
-+ sTouch.uiX = ADCGetData(4, 20);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ sTouch.state = TS_STATE_DONE;
-+
-+ /*
-+ * Process this set of ADC readings.
-+ */
-+ ProcessPointData();
-+
-+ break;
-+
-+ /*
-+ * Shouldn't get here. But if we do, we can recover...
-+ */
-+ case TS_STATE_DONE:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+ }
-+
-+ /*
-+ * Clear the timer2 interrupt.
-+ */
-+ __raw_writel(1, EP93XX_TIMER2_CLEAR);
-+ return(IRQ_HANDLED);
-+}
-+
-+/*---------------------------------------------------------------------
-+ * ProcessPointData
-+ *
-+ * This routine processes the ADC data into usable point data and then
-+ * puts the driver into hw or sw scanning mode before returning.
-+ *
-+ * We calculate inverse pressure (lower number = more pressure) then
-+ * do a hystheresis with the two pressure values 'light' and 'heavy'.
-+ *
-+ * If we are above the light, we have pen up.
-+ * If we are below the heavy we have pen down.
-+ * As long as the pressure stays below the light, pen stays down.
-+ * When we get above the light again, pen goes back up.
-+ *
-+ */
-+static void ProcessPointData(void)
-+{
-+ int bValidPoint = 0;
-+ unsigned int uiXDiff, uiYDiff, uiInvPressureDiff;
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Calculate the current pressure.
-+ */
-+ uiInvPressure = CalculateInvPressure();
-+
-+ /*
-+ * If pen pressure is so light that it is greater than the 'max' setting
-+ * then we consider this to be a pen up.
-+ */
-+ if (uiInvPressure >= TS_LIGHT_INV_PRESSURE)
-+ {
-+ bCurrentPenDown = 0;
-+ ee93xx_ts_evt_add(0, guiLastX, guiLastY, 0);
-+ TS_Hardware_Scan_Mode();
-+ return;
-+ }
-+
-+ /*
-+ * Hysteresis:
-+ * If the pen pressure is hard enough to be less than the 'min' OR
-+ * the pen is already down and is still less than the 'max'...
-+ */
-+ if ((uiInvPressure < TS_HEAVY_INV_PRESSURE) ||
-+ (bCurrentPenDown && (uiInvPressure < TS_LIGHT_INV_PRESSURE)))
-+ {
-+ if (bCurrentPenDown)
-+ {
-+ /*
-+ * If pen was previously down, check the difference between
-+ * the last sample and this one... if the difference between
-+ * samples is too great, ignore the sample.
-+ */
-+ uiXDiff = abs(guiLastX - sTouch.uiX);
-+ uiYDiff = abs(guiLastY - sTouch.uiY);
-+ uiInvPressureDiff = abs(guiLastInvPressure - uiInvPressure);
-+
-+ if (uiXDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiYDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiInvPressureDiff < TS_MAX_VALID_PRESSURE_CHANGE)
-+ {
-+ bValidPoint = 1;
-+ }
-+ }
-+ else
-+ {
-+ bValidPoint = 1;
-+ }
-+
-+ /*
-+ * If either the pen was put down or dragged make a note of it.
-+ */
-+ if (bValidPoint)
-+ {
-+ guiLastX = sTouch.uiX;
-+ guiLastY = sTouch.uiY;
-+ guiLastInvPressure = uiInvPressure;
-+ bCurrentPenDown = 1;
-+ ee93xx_ts_evt_add(1, sTouch.uiX, sTouch.uiY,
-+ 0x7000000 / uiInvPressure);
-+ }
-+
-+ TS_Soft_Scan_Mode();
-+ return;
-+ }
-+
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch)
-+{
-+ unsigned int uiResult;
-+
-+ /*
-+ * Set the switch settings in the direct register.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(uiADCSwitch, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ /*
-+ * Read and throw away the first sample.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+}
-+
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff)
-+{
-+ unsigned int uiResult, uiValue, uiCount, uiLowest, uiHighest, uiSum, uiAve;
-+
-+ do
-+ {
-+ /*
-+ * Initialize our values.
-+ */
-+ uiLowest = 0xfffffff;
-+ uiHighest = 0;
-+ uiSum = 0;
-+
-+ for (uiCount = 0; uiCount < uiSamples; uiCount++)
-+ {
-+ /*
-+ * Read the touch screen four more times and average.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+ uiValue = (uiResult & TSXYRESULT_AD_MASK) >> TSXYRESULT_AD_SHIFT;
-+ uiValue = ((uiValue >> 4) + ((1 + TSXYRESULT_X_MASK)>>1)) & TSXYRESULT_X_MASK;
-+
-+ /*
-+ * Add up the values.
-+ */
-+ uiSum += uiValue;
-+
-+ /*
-+ * Get the lowest and highest values.
-+ */
-+ if (uiValue < uiLowest)
-+ {
-+ uiLowest = uiValue;
-+ }
-+ if (uiValue > uiHighest)
-+ {
-+ uiHighest = uiValue;
-+ }
-+ }
-+ } while ((uiHighest - uiLowest) > uiMaxDiff);
-+
-+ /*
-+ * Calculate the Average value.
-+ */
-+ uiAve = uiSum / uiSamples;
-+
-+ return uiAve;
-+}
-+
-+/*
-+ * CalculateInvPressure
-+ *
-+ * Is the Touch Valid. Touch is not valid if the X or Y value is not
-+ * in range and the pressure is not enough.
-+ *
-+ * Touch resistance can be measured by the following formula:
-+ *
-+ * Rx * X * Z2
-+ * Rtouch = --------- * (-- - 1)
-+ * 4096 Z1
-+ *
-+ * This is simplified in the ration of Rtouch to Rx. The lower the value, the
-+ * higher the pressure.
-+ *
-+ * Z2
-+ * InvPressure = X * (-- - 1)
-+ * Z1
-+ */
-+static unsigned int CalculateInvPressure(void)
-+{
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Check to see if the point is valid.
-+ */
-+ if (sTouch.uiZ1 < MIN_Z1_VALUE)
-+ {
-+ uiInvPressure = 0x10000;
-+ }
-+
-+ /*
-+ * Can omit the pressure calculation if you need to get rid of the division.
-+ */
-+ else
-+ {
-+ uiInvPressure = ((sTouch.uiX * sTouch.uiZ2) / sTouch.uiZ1) - sTouch.uiX;
-+ }
-+
-+ return uiInvPressure;
-+}
-+
-+/*
-+ * TS_Hardware_Scan_Mode
-+ *
-+ * Enables the ep93xx ts scanning engine so that when the pen goes down
-+ * we will get an interrupt.
-+ */
-+static void TS_Hardware_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ /*
-+ * Disable the soft scanning engine.
-+ */
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Clear the TIN (Touchscreen INactive) bit so we can go to
-+ * automatic scanning mode.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg & ~EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+
-+ /*
-+ * Enable the touch screen scanning state machine by setting
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT | TSSETUP_ENABLE, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the flag to show that we are in interrupt mode.
-+ */
-+ gScanningMode = TS_MODE_HARDWARE_SCAN;
-+
-+ /*
-+ * Initialize EP93XX_TOUCHSCREEN_SETUP2 register.
-+ */
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+}
-+
-+/*
-+ * TS_Soft_Scan_Mode
-+ *
-+ * Sets the touch screen to manual polling mode.
-+ */
-+static void TS_Soft_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ if (gScanningMode != TS_MODE_SOFT_SCAN)
-+ {
-+ /*
-+ * Disable the touch screen scanning state machine by clearing
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the TIN bit so we can do manual touchscreen polling.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg | EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+ }
-+
-+ /*
-+ * Set the switch register up for the first ADC reading
-+ */
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ1);
-+
-+ /*
-+ * Initialize our software state machine to know which ADC
-+ * reading to take
-+ */
-+ sTouch.state = TS_STATE_Z1;
-+
-+ /*
-+ * Set the timer so after a mSec or two settling delay it will
-+ * take the first ADC reading.
-+ */
-+ Set_Timer2_uSec(EP93XX_TS_PER_POINT_DELAY_USEC);
-+
-+ /*
-+ * Note that we are in sw scanning mode not hw scanning mode.
-+ */
-+ gScanningMode = TS_MODE_SOFT_SCAN;
-+
-+}
-+
-+static void Set_Timer2_uSec(unsigned int uiDelay_uSec)
-+{
-+ unsigned int uiClockTicks;
-+
-+ /*
-+ * Stop timer 2
-+ */
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+
-+ uiClockTicks = ((uiDelay_uSec * 508) + 999) / 1000;
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_LOAD);
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_VALUE);
-+
-+ /*
-+ * Set up Timer 2 for 508 kHz clock and periodic mode.
-+ */
-+ __raw_writel(0xC8, EP93XX_TIMER2_CONTROL);
-+
-+}
-+
-+static void Stop_Timer2(void)
-+{
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+}
-+
-+/*
-+ * Initialization and exit routines
-+ */
-+int __init ep93xx_ts_init(void)
-+{
-+ int retval;
-+
-+ retval = request_irq(IRQ_EP93XX_TOUCH, ep93xx_ts_isr,
-+ IRQF_DISABLED, "ep93xx_ts", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get touchscreen IRQ\n");
-+ return retval;
-+ }
-+
-+ retval = request_irq(IRQ_EP93XX_TIMER2, ep93xx_timer2_isr,
-+ IRQF_DISABLED, "ep93xx_timer2", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get timer2 IRQ\n");
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ return retval;
-+ }
-+
-+ misc_register(&ep93xx_ts_miscdev);
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ gScanningMode = TS_MODE_UN_INITIALIZED;
-+
-+ printk(KERN_NOTICE "ep93xx touchscreen driver configured for 4-wire operation\n");
-+
-+ return 0;
-+}
-+
-+void __exit ep93xx_ts_exit(void)
-+{
-+ Stop_Timer2();
-+
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ free_irq(IRQ_EP93XX_TIMER2, 0);
-+
-+ misc_deregister(&ep93xx_ts_miscdev);
-+}
-+
-+module_init(ep93xx_ts_init);
-+module_exit(ep93xx_ts_exit);
-+
-+MODULE_DESCRIPTION("Cirrus EP93xx touchscreen driver");
-+MODULE_SUPPORTED_DEVICE("touchscreen/ep93xx");
-+MODULE_LICENSE("GPL");
---- a/arch/arm/mach-ep93xx/core.c
-+++ b/arch/arm/mach-ep93xx/core.c
-@@ -207,6 +207,7 @@ void ep93xx_syscon_swlocked_write(unsign
-
- spin_unlock_irqrestore(&syscon_swlock, flags);
- }
-+EXPORT_SYMBOL(ep93xx_syscon_swlocked_write);
-
- void ep93xx_devcfg_set_clear(unsigned int set_bits, unsigned int clear_bits)
- {
+++ /dev/null
-This enables the mmc-over-spi driver for the Sim.One board, based on Mika's
-patch, which used a GPIO for chip select in stead of the default SFRMOUT pin.
-I've modified it to use the usual SFRMOUT; if you've modified your Sim.One
-board to use a GPIO instead, uncomment and modify
-// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-in the source file.
- -martinwguy, 14 May 2010
-
-From: Mika Westerberg <mika.westerberg@iki.fi>
-Date: Wed, 28 Apr 2010 08:42:46 +0300
-Subject: [PATCH] ep93xx: simone: added board specific SPI support for MMC/SD cards
-
-This includes setting up EGPIOs 0 and 9 for card detection and chip select
-respectively.
-
---- a/arch/arm/mach-ep93xx/simone.c
-+++ b/arch/arm/mach-ep93xx/simone.c
-@@ -20,10 +20,15 @@
- #include <linux/platform_device.h>
- #include <linux/i2c.h>
- #include <linux/i2c-gpio.h>
-+#include <linux/gpio.h>
-+#include <linux/mmc/host.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/mmc_spi.h>
-
- #include <mach/hardware.h>
- #include <linux/platform_data/video-ep93xx.h>
- #include <mach/gpio-ep93xx.h>
-+#include <linux/platform_data/spi-ep93xx.h>
-
- #include <asm/mach-types.h>
- #include <asm/mach/arch.h>
-@@ -40,6 +45,135 @@ static struct ep93xxfb_mach_info __initd
- .flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
- };
-
-+/*
-+ * GPIO lines used for MMC card detection.
-+ */
-+#define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0
-+
-+/*
-+ * If you have hacked your Sim.One to use a GPIO as SD card chip select
-+ * (SD pin 1), uncomment the following line.
-+ * The example, EGPIO15, is on TP17 near the CPU.
-+ */
-+// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-+
-+/*
-+ * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal,
-+ * you can leave these empty and pass NULL as .controller_data.
-+ */
-+
-+#ifdef MMC_CHIP_SELECT_GPIO
-+static int simone_mmc_spi_setup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+ int err;
-+
-+ err = gpio_request(gpio, spi->modalias);
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_output(gpio, 1);
-+ if (err) {
-+ gpio_free(gpio);
-+ return err;
-+ }
-+
-+ return 0;
-+}
-+
-+static void simone_mmc_spi_cleanup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+
-+ gpio_set_value(gpio, 1);
-+ gpio_direction_input(gpio);
-+ gpio_free(gpio);
-+}
-+
-+static void simone_mmc_spi_cs_control(struct spi_device *spi, int value)
-+{
-+ gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-+}
-+
-+static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = {
-+ .setup = simone_mmc_spi_setup,
-+ .cleanup = simone_mmc_spi_cleanup,
-+ .cs_control = simone_mmc_spi_cs_control,
-+};
-+#endif
-+
-+/*
-+ * MMC card detection GPIO setup.
-+ */
-+static int simone_mmc_spi_init(struct device *dev,
-+ irqreturn_t (*irq_handler)(int, void *), void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+ int irq, err;
-+
-+ err = gpio_request(gpio, dev_name(dev));
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_input(gpio);
-+ if (err)
-+ goto fail;
-+
-+ irq = gpio_to_irq(gpio);
-+ if (irq < 0)
-+ goto fail;
-+
-+ err = request_irq(irq, irq_handler, IRQF_TRIGGER_FALLING,
-+ "MMC card detect", mmc);
-+ if (err)
-+ goto fail;
-+
-+ printk(KERN_INFO "%s: using irq %d for MMC card detection\n",
-+ dev_name(dev), irq);
-+
-+ return 0;
-+fail:
-+ gpio_free(gpio);
-+ return err;
-+}
-+
-+static void simone_mmc_spi_exit(struct device *dev, void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+
-+ free_irq(gpio_to_irq(gpio), mmc);
-+ gpio_free(gpio);
-+}
-+
-+static struct mmc_spi_platform_data simone_mmc_spi_data = {
-+ .init = simone_mmc_spi_init,
-+ .exit = simone_mmc_spi_exit,
-+ .detect_delay = 500,
-+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
-+};
-+
-+static struct spi_board_info simone_spi_devices[] __initdata = {
-+ {
-+ .modalias = "mmc_spi",
-+#ifdef MMC_CHIP_SELECT_GPIO
-+ .controller_data = &simone_mmc_spi_ops,
-+#endif
-+ .platform_data = &simone_mmc_spi_data,
-+ /*
-+ * We use 10 MHz even though the maximum is 3.7 MHz. The driver
-+ * will limit it automatically to max. frequency.
-+ */
-+ .max_speed_hz = 10 * 1000 * 1000,
-+ .bus_num = 0,
-+ .chip_select = 0,
-+ .mode = SPI_MODE_3,
-+ },
-+};
-+
-+static struct ep93xx_spi_info simone_spi_info __initdata = {
-+ .num_chipselect = ARRAY_SIZE(simone_spi_devices),
-+};
-+
- static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = {
- .sda_pin = EP93XX_GPIO_LINE_EEDAT,
- .sda_is_open_drain = 0,
-@@ -74,6 +208,8 @@ static void __init simone_init_machine(v
- ep93xx_register_fb(&simone_fb_info);
- ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
- ARRAY_SIZE(simone_i2c_board_info));
-+ ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
-+ ARRAY_SIZE(simone_spi_devices));
- simone_register_audio();
- }
-
+++ /dev/null
-This patch puts the EP93xx chip revision and unique ID into /proc/cpuinfo.
-This is necessary to be able to set a unique MAC address for DHCP purposes
-by adding a line to /etc/network/interfaces:
-
-# Generate a unique locally-assigned MAC address from the CPU serial number
-pre-up ifconfig eth0 hw ether `sed -n 's/^Serial.* 000000/02/p' /proc/cpuinfo`
-
-It uses the chip revision reading code in the ep93xx-chip-revision patch.
-
-Really, this is wrong, since /proc/cpuinfo should report the revision and
-serial number of the ARM920T processor, while these are the rev and serial
-of the EP93xx SoC. In a future kernel (>2.6.34) there may be a new file
-/proc/socinfo for this information.
-
- -martinwguy 14 May 2010
-
---- a/arch/arm/kernel/setup.c
-+++ b/arch/arm/kernel/setup.c
-@@ -57,6 +57,12 @@
- #include <asm/memblock.h>
- #include <asm/virt.h>
-
-+#if defined(CONFIG_ARCH_EP93XX)
-+#include <asm/io.h>
-+#include <mach/platform.h>
-+#include <mach/ep93xx-regs.h>
-+#endif
-+
- #include "atags.h"
-
-
-@@ -1052,9 +1058,16 @@ static int c_show(struct seq_file *m, vo
- }
-
- seq_printf(m, "Hardware\t: %s\n", machine_name);
-+#if defined(CONFIG_ARCH_EP93XX)
-+ seq_printf(m, "Revision\t: %04x\n",
-+ ep93xx_chip_revision());
-+ seq_printf(m, "Serial\t\t: %016x\n",
-+ *((unsigned int *)EP93XX_SECURITY_UNIQID));
-+#else
- seq_printf(m, "Revision\t: %04x\n", system_rev);
- seq_printf(m, "Serial\t\t: %08x%08x\n",
- system_serial_high, system_serial_low);
-+#endif
-
- return 0;
- }
---- a/arch/arm/mach-ep93xx/soc.h
-+++ b/arch/arm/mach-ep93xx/soc.h
-@@ -82,8 +82,6 @@
- #define EP93XX_I2S_PHYS_BASE EP93XX_APB_PHYS(0x00020000)
- #define EP93XX_I2S_BASE EP93XX_APB_IOMEM(0x00020000)
-
--#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
--
- #define EP93XX_AAC_PHYS_BASE EP93XX_APB_PHYS(0x00080000)
- #define EP93XX_AAC_BASE EP93XX_APB_IOMEM(0x00080000)
-
---- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-@@ -38,4 +38,8 @@
- #define EP93XX_UART3_PHYS_BASE EP93XX_APB_PHYS(0x000e0000)
- #define EP93XX_UART3_BASE EP93XX_APB_IOMEM(0x000e0000)
-
-+#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
-+#define EP93XX_SECURITY_REG(x) (EP93XX_SECURITY_BASE + (x))
-+#define EP93XX_SECURITY_UNIQID EP93XX_SECURITY_REG(0x2440)
-+
- #endif
+++ /dev/null
----
- arch/arm/mach-ep93xx/include/mach/hardware.h | 1
- arch/arm/mach-ep93xx/include/mach/regs_touch.h | 95 ++
- drivers/input/touchscreen/Kconfig | 5
- drivers/input/touchscreen/Makefile | 1
- drivers/input/touchscreen/ep93xx_ts.c | 1117 +++++++++++++++++++++++++
- drivers/input/touchscreen/ep93xx_ts.h | 53 +
- 6 files changed, 1272 insertions(+)
-
---- a/drivers/input/touchscreen/Kconfig
-+++ b/drivers/input/touchscreen/Kconfig
-@@ -265,6 +265,15 @@ config TOUCHSCREEN_EGALAX
- To compile this driver as a module, choose M here: the
- module will be called egalax_ts.
-
-+config TOUCHSCREEN_EP93XX
-+ tristate "EP93xx Touchscreen"
-+ depends on ARM && INPUT && ARCH_EP93XX
-+ help
-+ Say Y here to enable support for EP93xx touch screen.
-+
-+ To compile this driver as a module, choose M here:
-+ the module will be called ep93xx_ts.
-+
- config TOUCHSCREEN_FUJITSU
- tristate "Fujitsu serial touchscreen"
- select SERIO
---- a/drivers/input/touchscreen/Makefile
-+++ b/drivers/input/touchscreen/Makefile
-@@ -32,6 +32,7 @@ obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunz
- obj-$(CONFIG_TOUCHSCREEN_EETI) += eeti_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
- obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o
-+obj-$(CONFIG_TOUCHSCREEN_EP93XX) += ep93xx_ts.o
- obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
- obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
---- /dev/null
-+++ b/drivers/input/touchscreen/ep93xx_ts.c
-@@ -0,0 +1,1022 @@
-+/*
-+ * linux/drivers/input/touchscreen/ep93xx_ts.c
-+ *
-+ * Copyright (C) 2003-2004 Cirrus Corp.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/delay.h>
-+#include <linux/wait.h>
-+#include <linux/fs.h>
-+#include <linux/sched.h>
-+#include <linux/poll.h>
-+#include <linux/miscdevice.h>
-+#include <linux/init.h>
-+#include <linux/compiler.h>
-+#include <linux/timer.h>
-+#include <linux/interrupt.h>
-+#include <linux/syscalls.h>
-+#include <linux/input.h>
-+#include <linux/semaphore.h>
-+#include <asm/irq.h>
-+#include <mach/hardware.h>
-+#include <asm/io.h>
-+#include "../../../arch/arm/mach-ep93xx/soc.h"
-+
-+/* This stuff should be in ep93xx-regs.h */
-+#define EP93XX_TOUCHSCREEN_REG(x) (EP93XX_TOUCHSCREEN_BASE + (x))
-+/* R/W touchscreen controller setup control register. */
-+#define EP93XX_TOUCHSCREEN_SETUP EP93XX_TOUCHSCREEN_REG(0x00)
-+/* R/W touchscreen controller max/min register. */
-+#define EP93XX_TOUCHSCREEN_XYMAXMIN EP93XX_TOUCHSCREEN_REG(0x04)
-+/* R touchscreen controller result register. */
-+#define EP93XX_TOUCHSCREEN_XYRESULT EP93XX_TOUCHSCREEN_REG(0x08)
-+/* LOCKED R/W touchscreen Switch Matrix control register. */
-+#define EP93XX_TOUCHSCREEN_DISCHARGE EP93XX_TOUCHSCREEN_REG(0x0C)
-+#define EP93XX_TOUCHSCREEN_XSAMPLE EP93XX_TOUCHSCREEN_REG(0x10)
-+#define EP93XX_TOUCHSCREEN_YSAMPLE EP93XX_TOUCHSCREEN_REG(0x14)
-+#define EP93XX_TOUCHSCREEN_DIRECT EP93XX_TOUCHSCREEN_REG(0x18)
-+#define EP93XX_TOUCHSCREEN_DETECT EP93XX_TOUCHSCREEN_REG(0x1C)
-+/* NA R/W touchscreen software lock register. */
-+#define EP93XX_TOUCHSCREEN_SWLOCK EP93XX_TOUCHSCREEN_REG(0x20)
-+/* R/W touchscreen setup control register #2. */
-+#define EP93XX_TOUCHSCREEN_SETUP2 EP93XX_TOUCHSCREEN_REG(0x24)
-+
-+/* These are duplicated in mach-ep93xx/core.c */
-+#define EP93XX_TIMER_REG(x) (EP93XX_TIMER_BASE + (x))
-+#define EP93XX_TIMER2_LOAD EP93XX_TIMER_REG(0x20)
-+#define EP93XX_TIMER2_VALUE EP93XX_TIMER_REG(0x24)
-+#define EP93XX_TIMER2_CONTROL EP93XX_TIMER_REG(0x28)
-+#define EP93XX_TIMER2_CLEAR EP93XX_TIMER_REG(0x2c)
-+
-+/*
-+ * Register bit definitions
-+ */
-+#define TSSETUP_SDLY_MASK 0x000003FF
-+#define TSSETUP_SDLY_SHIFT 0
-+#define TSSETUP_NSMP_4 0x00000000
-+#define TSSETUP_NSMP_8 0x00000400
-+#define TSSETUP_NSMP_16 0x00000800
-+#define TSSETUP_NSMP_32 0x00000C00
-+#define TSSETUP_NSMP_MASK 0x00000C00
-+#define TSSETUP_DEV_4 0x00000000
-+#define TSSETUP_DEV_8 0x00001000
-+#define TSSETUP_DEV_12 0x00002000
-+#define TSSETUP_DEV_16 0x00003000
-+#define TSSETUP_DEV_24 0x00004000
-+#define TSSETUP_DEV_32 0x00005000
-+#define TSSETUP_DEV_64 0x00006000
-+#define TSSETUP_DEV_128 0x00007000
-+#define TSSETUP_ENABLE 0x00008000
-+#define TSSETUP_DLY_MASK 0x03FF0000
-+#define TSSETUP_DLY_SHIFT 16
-+#define TSSETUP_TDTCT 0x80000000
-+
-+#define TSMAXMIN_XMIN_MASK 0x000000FF
-+#define TSMAXMIN_XMIN_SHIFT 0
-+#define TSMAXMIN_YMIN_MASK 0x0000FF00
-+#define TSMAXMIN_YMIN_SHIFT 8
-+#define TSMAXMIN_XMAX_MASK 0x00FF0000
-+#define TSMAXMIN_XMAX_SHIFT 16
-+#define TSMAXMIN_YMAX_MASK 0xFF000000
-+#define TSMAXMIN_YMAX_SHIFT 24
-+
-+#define TSXYRESULT_X_MASK 0x00000FFF
-+#define TSXYRESULT_X_SHIFT 0
-+#define TSXYRESULT_AD_MASK 0x0000FFFF
-+#define TSXYRESULT_AD_SHIFT 0
-+#define TSXYRESULT_Y_MASK 0x0FFF0000
-+#define TSXYRESULT_Y_SHIFT 16
-+#define TSXYRESULT_SDR 0x80000000
-+
-+#define TSX_SAMPLE_MASK 0x00003FFF
-+#define TSX_SAMPLE_SHIFT 0x00
-+#define TSY_SAMPLE_MASK 0x3FFF0000
-+#define TSY_SAMPLE_SHIFT 0x10
-+
-+#define TSSETUP2_TINT 0x00000001
-+#define TSSETUP2_NICOR 0x00000002
-+#define TSSETUP2_PINT 0x00000004
-+#define TSSETUP2_PENSTS 0x00000008
-+#define TSSETUP2_PINTEN 0x00000010
-+#define TSSETUP2_DEVINT 0x00000020
-+#define TSSETUP2_DINTEN 0x00000040
-+#define TSSETUP2_DTMEN 0x00000080
-+#define TSSETUP2_DISDEV 0x00000100
-+#define TSSETUP2_NSIGND 0x00000200
-+#define TSSETUP2_S28EN 0x00000400
-+#define TSSETUP2_RINTEN 0x00000800
-+
-+#define TSXYRESULT_SDR 0x80000000
-+
-+/*
-+ * These are used as trigger levels to know when we have pen up/down.
-+ * The rules:
-+ * 1. TS_HEAVY_INV_PRESSURE < TS_LIGHT_INV_PRESSURE because these
-+ * are Inverse pressure.
-+ * 2. Any touch lighter than TS_LIGHT_INV_PRESSURE is a pen up.
-+ * 3. Any touch heavier than TS_HEAVY_INV_PRESSURE is a pen down.
-+ */
-+#define TS_HEAVY_INV_PRESSURE 0xFE0 /* C00 */
-+#define TS_LIGHT_INV_PRESSURE 0xFFF /* e00 */
-+
-+/*
-+ * If the x, y, or inverse pressure changes more than these values
-+ * between two succeeding points, the point is not reported.
-+ */
-+#define TS_MAX_VALID_XY_CHANGE 0x300
-+#define TS_MAX_VALID_PRESSURE_CHANGE 0x100
-+
-+/*
-+ * This is the minimum Z1 Value that is valid.
-+ */
-+#define MIN_Z1_VALUE 0x50
-+
-+/*
-+ * Settling delay for taking each ADC measurement. Increase this
-+ * if ts is jittery.
-+ */
-+#define EP93XX_TS_ADC_DELAY_USEC 2000
-+
-+/*
-+ * Delay between TS points.
-+ */
-+#define EP93XX_TS_PER_POINT_DELAY_USEC 10000
-+
-+/*
-+ * A few more macros...
-+ */
-+#define TSSETUP_DEFAULT (TSSETUP_NSMP_32 | TSSETUP_DEV_64 | \
-+ ((128<<TSSETUP_SDLY_SHIFT) & TSSETUP_SDLY_MASK) | \
-+ ((128<<TSSETUP_DLY_SHIFT) & TSSETUP_DLY_MASK))
-+
-+#define TSSETUP2_DEFAULT (TSSETUP2_NSIGND)
-+
-+/*
-+ * For now, we use one of the minor numbers from the local/experimental
-+ * range.
-+ */
-+#define EP93XX_TS_MINOR 240
-+
-+/*
-+ * Static Declarations
-+ */
-+static unsigned int guiLastX, guiLastY;
-+static unsigned int guiLastInvPressure;
-+
-+struct TouchScreenSample
-+{
-+ int currentX;
-+ int currentY;
-+ int currentButton;
-+ int currentPressure;
-+ struct timeval currentTime;
-+};
-+
-+/*
-+ * This must match the structure in tslib.
-+ */
-+struct ts_sample {
-+ int x;
-+ int y;
-+ unsigned int pressure;
-+ struct timeval tv;
-+};
-+
-+static struct TouchScreenSample gSample;
-+static int bFreshTouchData;
-+static int bCurrentPenDown;
-+
-+static DECLARE_WAIT_QUEUE_HEAD(queue);
-+static DEFINE_SEMAPHORE(open_sem);
-+static DEFINE_SPINLOCK(event_buffer_lock);
-+static struct fasync_struct *ep93xx_fasync;
-+
-+/*
-+ * Typedef Declarations
-+ */
-+typedef enum {
-+ TS_MODE_UN_INITIALIZED,
-+ TS_MODE_HARDWARE_SCAN,
-+ TS_MODE_SOFT_SCAN
-+} ts_mode_t;
-+
-+static ts_mode_t gScanningMode;
-+
-+typedef enum{
-+ TS_STATE_STOPPED = 0,
-+ TS_STATE_Z1,
-+ TS_STATE_Z2,
-+ TS_STATE_Y,
-+ TS_STATE_X,
-+ TS_STATE_DONE
-+} ts_states_t;
-+
-+typedef struct
-+{
-+ unsigned int uiX;
-+ unsigned int uiY;
-+ unsigned int uiZ1;
-+ unsigned int uiZ2;
-+ ts_states_t state;
-+} ts_struct_t;
-+
-+static ts_struct_t sTouch;
-+
-+/*
-+ * From the spec, here's how to set up the touch screen's switch registers.
-+ */
-+typedef struct
-+{
-+ unsigned int uiDetect;
-+ unsigned int uiDischarge;
-+ unsigned int uiXSample;
-+ unsigned int uiYSample;
-+ unsigned int uiSwitchZ1;
-+ unsigned int uiSwitchZ2;
-+}SwitchStructType;
-+
-+/*
-+ * Here's the switch settings for a 4-wire touchscreen. See the spec
-+ * for how to handle a 4, 7, or 8-wire.
-+ */
-+const static SwitchStructType sSwitchSettings =
-+/* s28en=0 */
-+/* TSDetect TSDischarge TSXSample TSYSample SwitchZ1 SwitchZ2 */
-+ {0x00403604, 0x0007fe04, 0x00081604, 0x00104601, 0x00101601, 0x00101608};
-+
-+/*
-+ * Function declarations
-+ */
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch);
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id);
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id);
-+static void ee93xx_ts_evt_add(int button, int dX, int dY, int Pressure);
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf,
-+ size_t count, loff_t *l);
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait);
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp);
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on);
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp);
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer,
-+ size_t count, loff_t *ppos);
-+static void ep93xx_ts_setup(void);
-+static void ep93xx_ts_shutdown(void);
-+int __init ep93xx_ts_init(void);
-+void __exit ep93xx_ts_exit(void);
-+static unsigned int CalculateInvPressure(void);
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff);
-+static void TS_Soft_Scan_Mode(void);
-+static void TS_Hardware_Scan_Mode(void);
-+static void ProcessPointData(void);
-+static void Set_Timer2_uSec(unsigned int Delay_mSec);
-+static void Stop_Timer2(void);
-+
-+/*
-+ * ep93xx_ts_isr
-+ */
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id)
-+{
-+ /*
-+ * Note that we don't clear the interrupt here. The interrupt
-+ * gets cleared in TS_Soft_Scan_Mode when the TS ENABLE
-+ * bit is cleared.
-+ */
-+
-+ /*
-+ * Set the ts to manual polling mode and schedule a callback.
-+ * That way we can return from the isr in a reasonable amount of
-+ * time and process the touch in the callback after a brief delay.
-+ */
-+ TS_Soft_Scan_Mode();
-+
-+ return(IRQ_HANDLED);
-+}
-+
-+/*
-+ * Save the current ts 'event' in an atomic fashion.
-+ */
-+static void ee93xx_ts_evt_add(int buttons, int iX, int iY, int iPressure)
-+{
-+ /*
-+ * Note the event, but use spinlocks to keep it from getting
-+ * halfway read if we get interrupted.
-+ */
-+
-+ spin_lock(&event_buffer_lock);
-+
-+ gSample.currentX = iX;
-+ gSample.currentY = iY;
-+ gSample.currentButton = buttons;
-+ gSample.currentPressure = iPressure;
-+ bFreshTouchData = 1;
-+ do_gettimeofday(&gSample.currentTime);
-+
-+ spin_unlock(&event_buffer_lock);
-+
-+ kill_fasync(&ep93xx_fasync, SIGIO, POLL_IN);
-+ wake_up_interruptible(&queue);
-+}
-+
-+
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf, size_t count, loff_t *l)
-+{
-+ unsigned short data[3];
-+ struct ts_sample ts_data;
-+ int iReturn = -EFAULT;
-+
-+ if (!bFreshTouchData)
-+ {
-+ iReturn = 0;
-+ }
-+ else if (count == sizeof(data))
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ data[0] = gSample.currentX;
-+ data[1] = gSample.currentY;
-+ data[2] = gSample.currentButton;
-+
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, data, sizeof data))
-+ return -EFAULT;
-+
-+ count -= sizeof(data);
-+
-+ /* return the # of bytes that got read */
-+ iReturn = sizeof(data) ;
-+ }
-+ else if (count == sizeof(struct ts_sample) )
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ ts_data.x = gSample.currentX;
-+ ts_data.y = gSample.currentY;
-+ ts_data.pressure = gSample.currentPressure;
-+ ts_data.tv = gSample.currentTime;
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, &ts_data, sizeof(struct ts_sample)))
-+ {
-+ iReturn = -EFAULT;
-+ }
-+ else
-+ {
-+ count -= sizeof(ts_data);
-+ iReturn = sizeof(ts_data);
-+ }
-+ }
-+
-+ return iReturn;
-+}
-+
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait)
-+{
-+ poll_wait(filp, &queue, wait);
-+
-+ if (bFreshTouchData)
-+ {
-+ return POLLIN | POLLRDNORM;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp)
-+{
-+ if (down_trylock(&open_sem))
-+ {
-+ return -EBUSY;
-+ }
-+
-+ ep93xx_ts_setup();
-+
-+ return 0;
-+}
-+
-+/*
-+ * Asynchronous I/O support.
-+ */
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on)
-+{
-+ int retval;
-+
-+ retval = fasync_helper(fd, filp, on, &ep93xx_fasync);
-+ if (retval < 0)
-+ {
-+ return retval;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp)
-+{
-+ Stop_Timer2();
-+
-+ /*
-+ * Call our async I/O support to request that this file
-+ * cease to be used for async I/O.
-+ */
-+ ep93xx_ts_fasync(-1, filp, 0);
-+
-+ ep93xx_ts_shutdown();
-+
-+ up(&open_sem);
-+
-+ return 0;
-+}
-+
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer, size_t count,
-+ loff_t *ppos)
-+{
-+ return -EINVAL;
-+}
-+
-+
-+static int ep93xx_ts_ioctl(struct inode *inode, struct file *file, uint command, ulong u)
-+{
-+ static const int version = EV_VERSION;
-+ static const u_int32_t bit =(1 << EV_ABS);
-+ static const u_int32_t absbit = (1 << ABS_X) | (1 << ABS_Y) | (1 << ABS_PRESSURE);
-+ int iReturn ;
-+ int i = 0;
-+
-+ switch(command)
-+ {
-+ case EVIOCGVERSION:
-+ i = copy_to_user((void __user *)u, (void *)version, sizeof(version));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(0,sizeof(u_int32_t) * 8) :
-+ i = copy_to_user((void __user *)u, (void *)bit, sizeof(bit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(EV_ABS, sizeof(absbit) * 8):
-+ i = copy_to_user((void __user *)u, (void *)absbit, sizeof(absbit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+ default:
-+ iReturn = -1;
-+ break;
-+ }
-+
-+ return iReturn;
-+}
-+
-+static struct file_operations ep93xx_ts_fops = {
-+ owner: THIS_MODULE,
-+ read: ep93xx_ts_read,
-+ write: ep93xx_ts_write,
-+ poll: ep93xx_ts_poll,
-+ open: ep93xx_ts_open,
-+ unlocked_ioctl: ep93xx_ts_ioctl,
-+ release: ep93xx_ts_release,
-+ fasync: ep93xx_ts_fasync,
-+};
-+
-+static struct miscdevice ep93xx_ts_miscdev =
-+{
-+ EP93XX_TS_MINOR,
-+ "ep93xx_ts",
-+ &ep93xx_ts_fops
-+};
-+
-+void ep93xx_ts_setup(void)
-+{
-+ unsigned int uiKTDIV, uiTSXYMaxMin;
-+
-+ /*
-+ * Set the TSEN bit in KTDIV so that we are enabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV |= EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+ /*
-+ * Program the EP93XX_TOUCHSCREEN_SETUP and TSSetup2 registers.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Set the the touch settings.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DISCHARGE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ1, EP93XX_TOUCHSCREEN_XSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ2, EP93XX_TOUCHSCREEN_YSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDetect, EP93XX_TOUCHSCREEN_DETECT);
-+
-+ /*
-+ * X,YMin set to 0x40 = have to drag that many pixels for a new irq.
-+ * X,YMax set to 0x40 = 1024 pixels is the maximum movement within the
-+ * time scan limit.
-+ */
-+ uiTSXYMaxMin = (50 << TSMAXMIN_XMIN_SHIFT) & TSMAXMIN_XMIN_MASK;
-+ uiTSXYMaxMin |= (50 << TSMAXMIN_YMIN_SHIFT) & TSMAXMIN_YMIN_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_XMAX_SHIFT) & TSMAXMIN_XMAX_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_YMAX_SHIFT) & TSMAXMIN_YMAX_MASK;
-+ __raw_writel(uiTSXYMaxMin, EP93XX_TOUCHSCREEN_XYMAXMIN);
-+
-+ bCurrentPenDown = 0;
-+ bFreshTouchData = 0;
-+ guiLastX = 0;
-+ guiLastY = 0;
-+ guiLastInvPressure = 0xffffff;
-+
-+ /*
-+ * Enable the touch screen scanning engine.
-+ */
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+/*
-+ * ep93xx_ts_shutdown
-+ *
-+ */
-+static void
-+ep93xx_ts_shutdown(void)
-+{
-+ unsigned int uiKTDIV;
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Disable the scanning engine.
-+ */
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Clear the TSEN bit in KTDIV so that we are disabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV &= ~EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+} /* ep93xx_ts_shutdown */
-+
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id)
-+{
-+ switch(sTouch.state)
-+ {
-+ case TS_STATE_STOPPED:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+
-+ /*
-+ * Get the Z1 value for pressure measurement and set up
-+ * the switch register for getting the Z2 measurement.
-+ */
-+ case TS_STATE_Z1:
-+ Set_Timer2_uSec(EP93XX_TS_ADC_DELAY_USEC);
-+ sTouch.uiZ1 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ2);
-+ sTouch.state = TS_STATE_Z2;
-+ break;
-+
-+ /*
-+ * Get the Z2 value for pressure measurement and set up
-+ * the switch register for getting the Y measurement.
-+ */
-+ case TS_STATE_Z2:
-+ sTouch.uiZ2 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiYSample);
-+ sTouch.state = TS_STATE_Y;
-+ break;
-+
-+ /*
-+ * Get the Y value and set up the switch register for
-+ * getting the X measurement.
-+ */
-+ case TS_STATE_Y:
-+ sTouch.uiY = ADCGetData(4, 20);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiXSample);
-+ sTouch.state = TS_STATE_X;
-+ break;
-+
-+ /*
-+ * Read the X value. This is the last of the 4 adc values
-+ * we need so we continue on to process the data.
-+ */
-+ case TS_STATE_X:
-+ Stop_Timer2();
-+
-+ sTouch.uiX = ADCGetData(4, 20);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ sTouch.state = TS_STATE_DONE;
-+
-+ /*
-+ * Process this set of ADC readings.
-+ */
-+ ProcessPointData();
-+
-+ break;
-+
-+ /*
-+ * Shouldn't get here. But if we do, we can recover...
-+ */
-+ case TS_STATE_DONE:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+ }
-+
-+ /*
-+ * Clear the timer2 interrupt.
-+ */
-+ __raw_writel(1, EP93XX_TIMER2_CLEAR);
-+ return(IRQ_HANDLED);
-+}
-+
-+/*---------------------------------------------------------------------
-+ * ProcessPointData
-+ *
-+ * This routine processes the ADC data into usable point data and then
-+ * puts the driver into hw or sw scanning mode before returning.
-+ *
-+ * We calculate inverse pressure (lower number = more pressure) then
-+ * do a hystheresis with the two pressure values 'light' and 'heavy'.
-+ *
-+ * If we are above the light, we have pen up.
-+ * If we are below the heavy we have pen down.
-+ * As long as the pressure stays below the light, pen stays down.
-+ * When we get above the light again, pen goes back up.
-+ *
-+ */
-+static void ProcessPointData(void)
-+{
-+ int bValidPoint = 0;
-+ unsigned int uiXDiff, uiYDiff, uiInvPressureDiff;
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Calculate the current pressure.
-+ */
-+ uiInvPressure = CalculateInvPressure();
-+
-+ /*
-+ * If pen pressure is so light that it is greater than the 'max' setting
-+ * then we consider this to be a pen up.
-+ */
-+ if (uiInvPressure >= TS_LIGHT_INV_PRESSURE)
-+ {
-+ bCurrentPenDown = 0;
-+ ee93xx_ts_evt_add(0, guiLastX, guiLastY, 0);
-+ TS_Hardware_Scan_Mode();
-+ return;
-+ }
-+
-+ /*
-+ * Hysteresis:
-+ * If the pen pressure is hard enough to be less than the 'min' OR
-+ * the pen is already down and is still less than the 'max'...
-+ */
-+ if ((uiInvPressure < TS_HEAVY_INV_PRESSURE) ||
-+ (bCurrentPenDown && (uiInvPressure < TS_LIGHT_INV_PRESSURE)))
-+ {
-+ if (bCurrentPenDown)
-+ {
-+ /*
-+ * If pen was previously down, check the difference between
-+ * the last sample and this one... if the difference between
-+ * samples is too great, ignore the sample.
-+ */
-+ uiXDiff = abs(guiLastX - sTouch.uiX);
-+ uiYDiff = abs(guiLastY - sTouch.uiY);
-+ uiInvPressureDiff = abs(guiLastInvPressure - uiInvPressure);
-+
-+ if (uiXDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiYDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiInvPressureDiff < TS_MAX_VALID_PRESSURE_CHANGE)
-+ {
-+ bValidPoint = 1;
-+ }
-+ }
-+ else
-+ {
-+ bValidPoint = 1;
-+ }
-+
-+ /*
-+ * If either the pen was put down or dragged make a note of it.
-+ */
-+ if (bValidPoint)
-+ {
-+ guiLastX = sTouch.uiX;
-+ guiLastY = sTouch.uiY;
-+ guiLastInvPressure = uiInvPressure;
-+ bCurrentPenDown = 1;
-+ ee93xx_ts_evt_add(1, sTouch.uiX, sTouch.uiY,
-+ 0x7000000 / uiInvPressure);
-+ }
-+
-+ TS_Soft_Scan_Mode();
-+ return;
-+ }
-+
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch)
-+{
-+ unsigned int uiResult;
-+
-+ /*
-+ * Set the switch settings in the direct register.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(uiADCSwitch, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ /*
-+ * Read and throw away the first sample.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+}
-+
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff)
-+{
-+ unsigned int uiResult, uiValue, uiCount, uiLowest, uiHighest, uiSum, uiAve;
-+
-+ do
-+ {
-+ /*
-+ * Initialize our values.
-+ */
-+ uiLowest = 0xfffffff;
-+ uiHighest = 0;
-+ uiSum = 0;
-+
-+ for (uiCount = 0; uiCount < uiSamples; uiCount++)
-+ {
-+ /*
-+ * Read the touch screen four more times and average.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+ uiValue = (uiResult & TSXYRESULT_AD_MASK) >> TSXYRESULT_AD_SHIFT;
-+ uiValue = ((uiValue >> 4) + ((1 + TSXYRESULT_X_MASK)>>1)) & TSXYRESULT_X_MASK;
-+
-+ /*
-+ * Add up the values.
-+ */
-+ uiSum += uiValue;
-+
-+ /*
-+ * Get the lowest and highest values.
-+ */
-+ if (uiValue < uiLowest)
-+ {
-+ uiLowest = uiValue;
-+ }
-+ if (uiValue > uiHighest)
-+ {
-+ uiHighest = uiValue;
-+ }
-+ }
-+ } while ((uiHighest - uiLowest) > uiMaxDiff);
-+
-+ /*
-+ * Calculate the Average value.
-+ */
-+ uiAve = uiSum / uiSamples;
-+
-+ return uiAve;
-+}
-+
-+/*
-+ * CalculateInvPressure
-+ *
-+ * Is the Touch Valid. Touch is not valid if the X or Y value is not
-+ * in range and the pressure is not enough.
-+ *
-+ * Touch resistance can be measured by the following formula:
-+ *
-+ * Rx * X * Z2
-+ * Rtouch = --------- * (-- - 1)
-+ * 4096 Z1
-+ *
-+ * This is simplified in the ration of Rtouch to Rx. The lower the value, the
-+ * higher the pressure.
-+ *
-+ * Z2
-+ * InvPressure = X * (-- - 1)
-+ * Z1
-+ */
-+static unsigned int CalculateInvPressure(void)
-+{
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Check to see if the point is valid.
-+ */
-+ if (sTouch.uiZ1 < MIN_Z1_VALUE)
-+ {
-+ uiInvPressure = 0x10000;
-+ }
-+
-+ /*
-+ * Can omit the pressure calculation if you need to get rid of the division.
-+ */
-+ else
-+ {
-+ uiInvPressure = ((sTouch.uiX * sTouch.uiZ2) / sTouch.uiZ1) - sTouch.uiX;
-+ }
-+
-+ return uiInvPressure;
-+}
-+
-+/*
-+ * TS_Hardware_Scan_Mode
-+ *
-+ * Enables the ep93xx ts scanning engine so that when the pen goes down
-+ * we will get an interrupt.
-+ */
-+static void TS_Hardware_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ /*
-+ * Disable the soft scanning engine.
-+ */
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Clear the TIN (Touchscreen INactive) bit so we can go to
-+ * automatic scanning mode.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg & ~EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+
-+ /*
-+ * Enable the touch screen scanning state machine by setting
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT | TSSETUP_ENABLE, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the flag to show that we are in interrupt mode.
-+ */
-+ gScanningMode = TS_MODE_HARDWARE_SCAN;
-+
-+ /*
-+ * Initialize EP93XX_TOUCHSCREEN_SETUP2 register.
-+ */
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+}
-+
-+/*
-+ * TS_Soft_Scan_Mode
-+ *
-+ * Sets the touch screen to manual polling mode.
-+ */
-+static void TS_Soft_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ if (gScanningMode != TS_MODE_SOFT_SCAN)
-+ {
-+ /*
-+ * Disable the touch screen scanning state machine by clearing
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the TIN bit so we can do manual touchscreen polling.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg | EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+ }
-+
-+ /*
-+ * Set the switch register up for the first ADC reading
-+ */
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ1);
-+
-+ /*
-+ * Initialize our software state machine to know which ADC
-+ * reading to take
-+ */
-+ sTouch.state = TS_STATE_Z1;
-+
-+ /*
-+ * Set the timer so after a mSec or two settling delay it will
-+ * take the first ADC reading.
-+ */
-+ Set_Timer2_uSec(EP93XX_TS_PER_POINT_DELAY_USEC);
-+
-+ /*
-+ * Note that we are in sw scanning mode not hw scanning mode.
-+ */
-+ gScanningMode = TS_MODE_SOFT_SCAN;
-+
-+}
-+
-+static void Set_Timer2_uSec(unsigned int uiDelay_uSec)
-+{
-+ unsigned int uiClockTicks;
-+
-+ /*
-+ * Stop timer 2
-+ */
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+
-+ uiClockTicks = ((uiDelay_uSec * 508) + 999) / 1000;
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_LOAD);
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_VALUE);
-+
-+ /*
-+ * Set up Timer 2 for 508 kHz clock and periodic mode.
-+ */
-+ __raw_writel(0xC8, EP93XX_TIMER2_CONTROL);
-+
-+}
-+
-+static void Stop_Timer2(void)
-+{
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+}
-+
-+/*
-+ * Initialization and exit routines
-+ */
-+int __init ep93xx_ts_init(void)
-+{
-+ int retval;
-+
-+ retval = request_irq(IRQ_EP93XX_TOUCH, ep93xx_ts_isr,
-+ IRQF_DISABLED, "ep93xx_ts", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get touchscreen IRQ\n");
-+ return retval;
-+ }
-+
-+ retval = request_irq(IRQ_EP93XX_TIMER2, ep93xx_timer2_isr,
-+ IRQF_DISABLED, "ep93xx_timer2", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get timer2 IRQ\n");
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ return retval;
-+ }
-+
-+ misc_register(&ep93xx_ts_miscdev);
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ gScanningMode = TS_MODE_UN_INITIALIZED;
-+
-+ printk(KERN_NOTICE "ep93xx touchscreen driver configured for 4-wire operation\n");
-+
-+ return 0;
-+}
-+
-+void __exit ep93xx_ts_exit(void)
-+{
-+ Stop_Timer2();
-+
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ free_irq(IRQ_EP93XX_TIMER2, 0);
-+
-+ misc_deregister(&ep93xx_ts_miscdev);
-+}
-+
-+module_init(ep93xx_ts_init);
-+module_exit(ep93xx_ts_exit);
-+
-+MODULE_DESCRIPTION("Cirrus EP93xx touchscreen driver");
-+MODULE_SUPPORTED_DEVICE("touchscreen/ep93xx");
-+MODULE_LICENSE("GPL");
---- a/arch/arm/mach-ep93xx/core.c
-+++ b/arch/arm/mach-ep93xx/core.c
-@@ -211,6 +211,7 @@ void ep93xx_syscon_swlocked_write(unsign
-
- spin_unlock_irqrestore(&syscon_swlock, flags);
- }
-+EXPORT_SYMBOL(ep93xx_syscon_swlocked_write);
-
- void ep93xx_devcfg_set_clear(unsigned int set_bits, unsigned int clear_bits)
- {
+++ /dev/null
-This enables the mmc-over-spi driver for the Sim.One board, based on Mika's
-patch, which used a GPIO for chip select in stead of the default SFRMOUT pin.
-I've modified it to use the usual SFRMOUT; if you've modified your Sim.One
-board to use a GPIO instead, uncomment and modify
-// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-in the source file.
- -martinwguy, 14 May 2010
-
-From: Mika Westerberg <mika.westerberg@iki.fi>
-Date: Wed, 28 Apr 2010 08:42:46 +0300
-Subject: [PATCH] ep93xx: simone: added board specific SPI support for MMC/SD cards
-
-This includes setting up EGPIOs 0 and 9 for card detection and chip select
-respectively.
-
---- a/arch/arm/mach-ep93xx/simone.c
-+++ b/arch/arm/mach-ep93xx/simone.c
-@@ -20,10 +20,15 @@
- #include <linux/platform_device.h>
- #include <linux/i2c.h>
- #include <linux/i2c-gpio.h>
-+#include <linux/gpio.h>
-+#include <linux/mmc/host.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/mmc_spi.h>
-
- #include <mach/hardware.h>
- #include <linux/platform_data/video-ep93xx.h>
- #include <mach/gpio-ep93xx.h>
-+#include <linux/platform_data/spi-ep93xx.h>
-
- #include <asm/mach-types.h>
- #include <asm/mach/arch.h>
-@@ -40,6 +45,135 @@ static struct ep93xxfb_mach_info __initd
- .flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
- };
-
-+/*
-+ * GPIO lines used for MMC card detection.
-+ */
-+#define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0
-+
-+/*
-+ * If you have hacked your Sim.One to use a GPIO as SD card chip select
-+ * (SD pin 1), uncomment the following line.
-+ * The example, EGPIO15, is on TP17 near the CPU.
-+ */
-+// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-+
-+/*
-+ * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal,
-+ * you can leave these empty and pass NULL as .controller_data.
-+ */
-+
-+#ifdef MMC_CHIP_SELECT_GPIO
-+static int simone_mmc_spi_setup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+ int err;
-+
-+ err = gpio_request(gpio, spi->modalias);
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_output(gpio, 1);
-+ if (err) {
-+ gpio_free(gpio);
-+ return err;
-+ }
-+
-+ return 0;
-+}
-+
-+static void simone_mmc_spi_cleanup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+
-+ gpio_set_value(gpio, 1);
-+ gpio_direction_input(gpio);
-+ gpio_free(gpio);
-+}
-+
-+static void simone_mmc_spi_cs_control(struct spi_device *spi, int value)
-+{
-+ gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-+}
-+
-+static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = {
-+ .setup = simone_mmc_spi_setup,
-+ .cleanup = simone_mmc_spi_cleanup,
-+ .cs_control = simone_mmc_spi_cs_control,
-+};
-+#endif
-+
-+/*
-+ * MMC card detection GPIO setup.
-+ */
-+static int simone_mmc_spi_init(struct device *dev,
-+ irqreturn_t (*irq_handler)(int, void *), void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+ int irq, err;
-+
-+ err = gpio_request(gpio, dev_name(dev));
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_input(gpio);
-+ if (err)
-+ goto fail;
-+
-+ irq = gpio_to_irq(gpio);
-+ if (irq < 0)
-+ goto fail;
-+
-+ err = request_irq(irq, irq_handler, IRQF_TRIGGER_FALLING,
-+ "MMC card detect", mmc);
-+ if (err)
-+ goto fail;
-+
-+ printk(KERN_INFO "%s: using irq %d for MMC card detection\n",
-+ dev_name(dev), irq);
-+
-+ return 0;
-+fail:
-+ gpio_free(gpio);
-+ return err;
-+}
-+
-+static void simone_mmc_spi_exit(struct device *dev, void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+
-+ free_irq(gpio_to_irq(gpio), mmc);
-+ gpio_free(gpio);
-+}
-+
-+static struct mmc_spi_platform_data simone_mmc_spi_data = {
-+ .init = simone_mmc_spi_init,
-+ .exit = simone_mmc_spi_exit,
-+ .detect_delay = 500,
-+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
-+};
-+
-+static struct spi_board_info simone_spi_devices[] __initdata = {
-+ {
-+ .modalias = "mmc_spi",
-+#ifdef MMC_CHIP_SELECT_GPIO
-+ .controller_data = &simone_mmc_spi_ops,
-+#endif
-+ .platform_data = &simone_mmc_spi_data,
-+ /*
-+ * We use 10 MHz even though the maximum is 3.7 MHz. The driver
-+ * will limit it automatically to max. frequency.
-+ */
-+ .max_speed_hz = 10 * 1000 * 1000,
-+ .bus_num = 0,
-+ .chip_select = 0,
-+ .mode = SPI_MODE_3,
-+ },
-+};
-+
-+static struct ep93xx_spi_info simone_spi_info __initdata = {
-+ .num_chipselect = ARRAY_SIZE(simone_spi_devices),
-+};
-+
- static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = {
- .sda_pin = EP93XX_GPIO_LINE_EEDAT,
- .sda_is_open_drain = 0,
-@@ -74,6 +208,8 @@ static void __init simone_init_machine(v
- ep93xx_register_fb(&simone_fb_info);
- ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
- ARRAY_SIZE(simone_i2c_board_info));
-+ ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
-+ ARRAY_SIZE(simone_spi_devices));
- simone_register_audio();
- }
-
+++ /dev/null
-This patch puts the EP93xx chip revision and unique ID into /proc/cpuinfo.
-This is necessary to be able to set a unique MAC address for DHCP purposes
-by adding a line to /etc/network/interfaces:
-
-# Generate a unique locally-assigned MAC address from the CPU serial number
-pre-up ifconfig eth0 hw ether `sed -n 's/^Serial.* 000000/02/p' /proc/cpuinfo`
-
-It uses the chip revision reading code in the ep93xx-chip-revision patch.
-
-Really, this is wrong, since /proc/cpuinfo should report the revision and
-serial number of the ARM920T processor, while these are the rev and serial
-of the EP93xx SoC. In a future kernel (>2.6.34) there may be a new file
-/proc/socinfo for this information.
-
- -martinwguy 14 May 2010
-
---- a/arch/arm/kernel/setup.c
-+++ b/arch/arm/kernel/setup.c
-@@ -57,6 +57,12 @@
- #include <asm/memblock.h>
- #include <asm/virt.h>
-
-+#if defined(CONFIG_ARCH_EP93XX)
-+#include <asm/io.h>
-+#include <mach/platform.h>
-+#include <mach/ep93xx-regs.h>
-+#endif
-+
- #include "atags.h"
-
-
-@@ -1087,9 +1093,16 @@ static int c_show(struct seq_file *m, vo
- }
-
- seq_printf(m, "Hardware\t: %s\n", machine_name);
-+#if defined(CONFIG_ARCH_EP93XX)
-+ seq_printf(m, "Revision\t: %04x\n",
-+ ep93xx_chip_revision());
-+ seq_printf(m, "Serial\t\t: %016x\n",
-+ *((unsigned int *)EP93XX_SECURITY_UNIQID));
-+#else
- seq_printf(m, "Revision\t: %04x\n", system_rev);
- seq_printf(m, "Serial\t\t: %08x%08x\n",
- system_serial_high, system_serial_low);
-+#endif
-
- return 0;
- }
---- a/arch/arm/mach-ep93xx/soc.h
-+++ b/arch/arm/mach-ep93xx/soc.h
-@@ -82,8 +82,6 @@
- #define EP93XX_I2S_PHYS_BASE EP93XX_APB_PHYS(0x00020000)
- #define EP93XX_I2S_BASE EP93XX_APB_IOMEM(0x00020000)
-
--#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
--
- #define EP93XX_AAC_PHYS_BASE EP93XX_APB_PHYS(0x00080000)
- #define EP93XX_AAC_BASE EP93XX_APB_IOMEM(0x00080000)
-
---- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-@@ -38,4 +38,8 @@
- #define EP93XX_UART3_PHYS_BASE EP93XX_APB_PHYS(0x000e0000)
- #define EP93XX_UART3_BASE EP93XX_APB_IOMEM(0x000e0000)
-
-+#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
-+#define EP93XX_SECURITY_REG(x) (EP93XX_SECURITY_BASE + (x))
-+#define EP93XX_SECURITY_UNIQID EP93XX_SECURITY_REG(0x2440)
-+
- #endif
+++ /dev/null
----
- arch/arm/mach-ep93xx/include/mach/hardware.h | 1
- arch/arm/mach-ep93xx/include/mach/regs_touch.h | 95 ++
- drivers/input/touchscreen/Kconfig | 5
- drivers/input/touchscreen/Makefile | 1
- drivers/input/touchscreen/ep93xx_ts.c | 1117 +++++++++++++++++++++++++
- drivers/input/touchscreen/ep93xx_ts.h | 53 +
- 6 files changed, 1272 insertions(+)
-
---- a/drivers/input/touchscreen/Kconfig
-+++ b/drivers/input/touchscreen/Kconfig
-@@ -282,6 +282,15 @@ config TOUCHSCREEN_EGALAX
- To compile this driver as a module, choose M here: the
- module will be called egalax_ts.
-
-+config TOUCHSCREEN_EP93XX
-+ tristate "EP93xx Touchscreen"
-+ depends on ARM && INPUT && ARCH_EP93XX
-+ help
-+ Say Y here to enable support for EP93xx touch screen.
-+
-+ To compile this driver as a module, choose M here:
-+ the module will be called ep93xx_ts.
-+
- config TOUCHSCREEN_FUJITSU
- tristate "Fujitsu serial touchscreen"
- select SERIO
---- a/drivers/input/touchscreen/Makefile
-+++ b/drivers/input/touchscreen/Makefile
-@@ -33,6 +33,7 @@ obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunz
- obj-$(CONFIG_TOUCHSCREEN_EETI) += eeti_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
- obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o
-+obj-$(CONFIG_TOUCHSCREEN_EP93XX) += ep93xx_ts.o
- obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
- obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
---- /dev/null
-+++ b/drivers/input/touchscreen/ep93xx_ts.c
-@@ -0,0 +1,1022 @@
-+/*
-+ * linux/drivers/input/touchscreen/ep93xx_ts.c
-+ *
-+ * Copyright (C) 2003-2004 Cirrus Corp.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/delay.h>
-+#include <linux/wait.h>
-+#include <linux/fs.h>
-+#include <linux/sched.h>
-+#include <linux/poll.h>
-+#include <linux/miscdevice.h>
-+#include <linux/init.h>
-+#include <linux/compiler.h>
-+#include <linux/timer.h>
-+#include <linux/interrupt.h>
-+#include <linux/syscalls.h>
-+#include <linux/input.h>
-+#include <linux/semaphore.h>
-+#include <asm/irq.h>
-+#include <mach/hardware.h>
-+#include <asm/io.h>
-+#include "../../../arch/arm/mach-ep93xx/soc.h"
-+
-+/* This stuff should be in ep93xx-regs.h */
-+#define EP93XX_TOUCHSCREEN_REG(x) (EP93XX_TOUCHSCREEN_BASE + (x))
-+/* R/W touchscreen controller setup control register. */
-+#define EP93XX_TOUCHSCREEN_SETUP EP93XX_TOUCHSCREEN_REG(0x00)
-+/* R/W touchscreen controller max/min register. */
-+#define EP93XX_TOUCHSCREEN_XYMAXMIN EP93XX_TOUCHSCREEN_REG(0x04)
-+/* R touchscreen controller result register. */
-+#define EP93XX_TOUCHSCREEN_XYRESULT EP93XX_TOUCHSCREEN_REG(0x08)
-+/* LOCKED R/W touchscreen Switch Matrix control register. */
-+#define EP93XX_TOUCHSCREEN_DISCHARGE EP93XX_TOUCHSCREEN_REG(0x0C)
-+#define EP93XX_TOUCHSCREEN_XSAMPLE EP93XX_TOUCHSCREEN_REG(0x10)
-+#define EP93XX_TOUCHSCREEN_YSAMPLE EP93XX_TOUCHSCREEN_REG(0x14)
-+#define EP93XX_TOUCHSCREEN_DIRECT EP93XX_TOUCHSCREEN_REG(0x18)
-+#define EP93XX_TOUCHSCREEN_DETECT EP93XX_TOUCHSCREEN_REG(0x1C)
-+/* NA R/W touchscreen software lock register. */
-+#define EP93XX_TOUCHSCREEN_SWLOCK EP93XX_TOUCHSCREEN_REG(0x20)
-+/* R/W touchscreen setup control register #2. */
-+#define EP93XX_TOUCHSCREEN_SETUP2 EP93XX_TOUCHSCREEN_REG(0x24)
-+
-+/* These are duplicated in mach-ep93xx/core.c */
-+#define EP93XX_TIMER_REG(x) (EP93XX_TIMER_BASE + (x))
-+#define EP93XX_TIMER2_LOAD EP93XX_TIMER_REG(0x20)
-+#define EP93XX_TIMER2_VALUE EP93XX_TIMER_REG(0x24)
-+#define EP93XX_TIMER2_CONTROL EP93XX_TIMER_REG(0x28)
-+#define EP93XX_TIMER2_CLEAR EP93XX_TIMER_REG(0x2c)
-+
-+/*
-+ * Register bit definitions
-+ */
-+#define TSSETUP_SDLY_MASK 0x000003FF
-+#define TSSETUP_SDLY_SHIFT 0
-+#define TSSETUP_NSMP_4 0x00000000
-+#define TSSETUP_NSMP_8 0x00000400
-+#define TSSETUP_NSMP_16 0x00000800
-+#define TSSETUP_NSMP_32 0x00000C00
-+#define TSSETUP_NSMP_MASK 0x00000C00
-+#define TSSETUP_DEV_4 0x00000000
-+#define TSSETUP_DEV_8 0x00001000
-+#define TSSETUP_DEV_12 0x00002000
-+#define TSSETUP_DEV_16 0x00003000
-+#define TSSETUP_DEV_24 0x00004000
-+#define TSSETUP_DEV_32 0x00005000
-+#define TSSETUP_DEV_64 0x00006000
-+#define TSSETUP_DEV_128 0x00007000
-+#define TSSETUP_ENABLE 0x00008000
-+#define TSSETUP_DLY_MASK 0x03FF0000
-+#define TSSETUP_DLY_SHIFT 16
-+#define TSSETUP_TDTCT 0x80000000
-+
-+#define TSMAXMIN_XMIN_MASK 0x000000FF
-+#define TSMAXMIN_XMIN_SHIFT 0
-+#define TSMAXMIN_YMIN_MASK 0x0000FF00
-+#define TSMAXMIN_YMIN_SHIFT 8
-+#define TSMAXMIN_XMAX_MASK 0x00FF0000
-+#define TSMAXMIN_XMAX_SHIFT 16
-+#define TSMAXMIN_YMAX_MASK 0xFF000000
-+#define TSMAXMIN_YMAX_SHIFT 24
-+
-+#define TSXYRESULT_X_MASK 0x00000FFF
-+#define TSXYRESULT_X_SHIFT 0
-+#define TSXYRESULT_AD_MASK 0x0000FFFF
-+#define TSXYRESULT_AD_SHIFT 0
-+#define TSXYRESULT_Y_MASK 0x0FFF0000
-+#define TSXYRESULT_Y_SHIFT 16
-+#define TSXYRESULT_SDR 0x80000000
-+
-+#define TSX_SAMPLE_MASK 0x00003FFF
-+#define TSX_SAMPLE_SHIFT 0x00
-+#define TSY_SAMPLE_MASK 0x3FFF0000
-+#define TSY_SAMPLE_SHIFT 0x10
-+
-+#define TSSETUP2_TINT 0x00000001
-+#define TSSETUP2_NICOR 0x00000002
-+#define TSSETUP2_PINT 0x00000004
-+#define TSSETUP2_PENSTS 0x00000008
-+#define TSSETUP2_PINTEN 0x00000010
-+#define TSSETUP2_DEVINT 0x00000020
-+#define TSSETUP2_DINTEN 0x00000040
-+#define TSSETUP2_DTMEN 0x00000080
-+#define TSSETUP2_DISDEV 0x00000100
-+#define TSSETUP2_NSIGND 0x00000200
-+#define TSSETUP2_S28EN 0x00000400
-+#define TSSETUP2_RINTEN 0x00000800
-+
-+#define TSXYRESULT_SDR 0x80000000
-+
-+/*
-+ * These are used as trigger levels to know when we have pen up/down.
-+ * The rules:
-+ * 1. TS_HEAVY_INV_PRESSURE < TS_LIGHT_INV_PRESSURE because these
-+ * are Inverse pressure.
-+ * 2. Any touch lighter than TS_LIGHT_INV_PRESSURE is a pen up.
-+ * 3. Any touch heavier than TS_HEAVY_INV_PRESSURE is a pen down.
-+ */
-+#define TS_HEAVY_INV_PRESSURE 0xFE0 /* C00 */
-+#define TS_LIGHT_INV_PRESSURE 0xFFF /* e00 */
-+
-+/*
-+ * If the x, y, or inverse pressure changes more than these values
-+ * between two succeeding points, the point is not reported.
-+ */
-+#define TS_MAX_VALID_XY_CHANGE 0x300
-+#define TS_MAX_VALID_PRESSURE_CHANGE 0x100
-+
-+/*
-+ * This is the minimum Z1 Value that is valid.
-+ */
-+#define MIN_Z1_VALUE 0x50
-+
-+/*
-+ * Settling delay for taking each ADC measurement. Increase this
-+ * if ts is jittery.
-+ */
-+#define EP93XX_TS_ADC_DELAY_USEC 2000
-+
-+/*
-+ * Delay between TS points.
-+ */
-+#define EP93XX_TS_PER_POINT_DELAY_USEC 10000
-+
-+/*
-+ * A few more macros...
-+ */
-+#define TSSETUP_DEFAULT (TSSETUP_NSMP_32 | TSSETUP_DEV_64 | \
-+ ((128<<TSSETUP_SDLY_SHIFT) & TSSETUP_SDLY_MASK) | \
-+ ((128<<TSSETUP_DLY_SHIFT) & TSSETUP_DLY_MASK))
-+
-+#define TSSETUP2_DEFAULT (TSSETUP2_NSIGND)
-+
-+/*
-+ * For now, we use one of the minor numbers from the local/experimental
-+ * range.
-+ */
-+#define EP93XX_TS_MINOR 240
-+
-+/*
-+ * Static Declarations
-+ */
-+static unsigned int guiLastX, guiLastY;
-+static unsigned int guiLastInvPressure;
-+
-+struct TouchScreenSample
-+{
-+ int currentX;
-+ int currentY;
-+ int currentButton;
-+ int currentPressure;
-+ struct timeval currentTime;
-+};
-+
-+/*
-+ * This must match the structure in tslib.
-+ */
-+struct ts_sample {
-+ int x;
-+ int y;
-+ unsigned int pressure;
-+ struct timeval tv;
-+};
-+
-+static struct TouchScreenSample gSample;
-+static int bFreshTouchData;
-+static int bCurrentPenDown;
-+
-+static DECLARE_WAIT_QUEUE_HEAD(queue);
-+static DEFINE_SEMAPHORE(open_sem);
-+static DEFINE_SPINLOCK(event_buffer_lock);
-+static struct fasync_struct *ep93xx_fasync;
-+
-+/*
-+ * Typedef Declarations
-+ */
-+typedef enum {
-+ TS_MODE_UN_INITIALIZED,
-+ TS_MODE_HARDWARE_SCAN,
-+ TS_MODE_SOFT_SCAN
-+} ts_mode_t;
-+
-+static ts_mode_t gScanningMode;
-+
-+typedef enum{
-+ TS_STATE_STOPPED = 0,
-+ TS_STATE_Z1,
-+ TS_STATE_Z2,
-+ TS_STATE_Y,
-+ TS_STATE_X,
-+ TS_STATE_DONE
-+} ts_states_t;
-+
-+typedef struct
-+{
-+ unsigned int uiX;
-+ unsigned int uiY;
-+ unsigned int uiZ1;
-+ unsigned int uiZ2;
-+ ts_states_t state;
-+} ts_struct_t;
-+
-+static ts_struct_t sTouch;
-+
-+/*
-+ * From the spec, here's how to set up the touch screen's switch registers.
-+ */
-+typedef struct
-+{
-+ unsigned int uiDetect;
-+ unsigned int uiDischarge;
-+ unsigned int uiXSample;
-+ unsigned int uiYSample;
-+ unsigned int uiSwitchZ1;
-+ unsigned int uiSwitchZ2;
-+}SwitchStructType;
-+
-+/*
-+ * Here's the switch settings for a 4-wire touchscreen. See the spec
-+ * for how to handle a 4, 7, or 8-wire.
-+ */
-+const static SwitchStructType sSwitchSettings =
-+/* s28en=0 */
-+/* TSDetect TSDischarge TSXSample TSYSample SwitchZ1 SwitchZ2 */
-+ {0x00403604, 0x0007fe04, 0x00081604, 0x00104601, 0x00101601, 0x00101608};
-+
-+/*
-+ * Function declarations
-+ */
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch);
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id);
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id);
-+static void ee93xx_ts_evt_add(int button, int dX, int dY, int Pressure);
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf,
-+ size_t count, loff_t *l);
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait);
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp);
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on);
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp);
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer,
-+ size_t count, loff_t *ppos);
-+static void ep93xx_ts_setup(void);
-+static void ep93xx_ts_shutdown(void);
-+int __init ep93xx_ts_init(void);
-+void __exit ep93xx_ts_exit(void);
-+static unsigned int CalculateInvPressure(void);
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff);
-+static void TS_Soft_Scan_Mode(void);
-+static void TS_Hardware_Scan_Mode(void);
-+static void ProcessPointData(void);
-+static void Set_Timer2_uSec(unsigned int Delay_mSec);
-+static void Stop_Timer2(void);
-+
-+/*
-+ * ep93xx_ts_isr
-+ */
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id)
-+{
-+ /*
-+ * Note that we don't clear the interrupt here. The interrupt
-+ * gets cleared in TS_Soft_Scan_Mode when the TS ENABLE
-+ * bit is cleared.
-+ */
-+
-+ /*
-+ * Set the ts to manual polling mode and schedule a callback.
-+ * That way we can return from the isr in a reasonable amount of
-+ * time and process the touch in the callback after a brief delay.
-+ */
-+ TS_Soft_Scan_Mode();
-+
-+ return(IRQ_HANDLED);
-+}
-+
-+/*
-+ * Save the current ts 'event' in an atomic fashion.
-+ */
-+static void ee93xx_ts_evt_add(int buttons, int iX, int iY, int iPressure)
-+{
-+ /*
-+ * Note the event, but use spinlocks to keep it from getting
-+ * halfway read if we get interrupted.
-+ */
-+
-+ spin_lock(&event_buffer_lock);
-+
-+ gSample.currentX = iX;
-+ gSample.currentY = iY;
-+ gSample.currentButton = buttons;
-+ gSample.currentPressure = iPressure;
-+ bFreshTouchData = 1;
-+ do_gettimeofday(&gSample.currentTime);
-+
-+ spin_unlock(&event_buffer_lock);
-+
-+ kill_fasync(&ep93xx_fasync, SIGIO, POLL_IN);
-+ wake_up_interruptible(&queue);
-+}
-+
-+
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf, size_t count, loff_t *l)
-+{
-+ unsigned short data[3];
-+ struct ts_sample ts_data;
-+ int iReturn = -EFAULT;
-+
-+ if (!bFreshTouchData)
-+ {
-+ iReturn = 0;
-+ }
-+ else if (count == sizeof(data))
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ data[0] = gSample.currentX;
-+ data[1] = gSample.currentY;
-+ data[2] = gSample.currentButton;
-+
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, data, sizeof data))
-+ return -EFAULT;
-+
-+ count -= sizeof(data);
-+
-+ /* return the # of bytes that got read */
-+ iReturn = sizeof(data) ;
-+ }
-+ else if (count == sizeof(struct ts_sample) )
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ ts_data.x = gSample.currentX;
-+ ts_data.y = gSample.currentY;
-+ ts_data.pressure = gSample.currentPressure;
-+ ts_data.tv = gSample.currentTime;
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, &ts_data, sizeof(struct ts_sample)))
-+ {
-+ iReturn = -EFAULT;
-+ }
-+ else
-+ {
-+ count -= sizeof(ts_data);
-+ iReturn = sizeof(ts_data);
-+ }
-+ }
-+
-+ return iReturn;
-+}
-+
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait)
-+{
-+ poll_wait(filp, &queue, wait);
-+
-+ if (bFreshTouchData)
-+ {
-+ return POLLIN | POLLRDNORM;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp)
-+{
-+ if (down_trylock(&open_sem))
-+ {
-+ return -EBUSY;
-+ }
-+
-+ ep93xx_ts_setup();
-+
-+ return 0;
-+}
-+
-+/*
-+ * Asynchronous I/O support.
-+ */
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on)
-+{
-+ int retval;
-+
-+ retval = fasync_helper(fd, filp, on, &ep93xx_fasync);
-+ if (retval < 0)
-+ {
-+ return retval;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp)
-+{
-+ Stop_Timer2();
-+
-+ /*
-+ * Call our async I/O support to request that this file
-+ * cease to be used for async I/O.
-+ */
-+ ep93xx_ts_fasync(-1, filp, 0);
-+
-+ ep93xx_ts_shutdown();
-+
-+ up(&open_sem);
-+
-+ return 0;
-+}
-+
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer, size_t count,
-+ loff_t *ppos)
-+{
-+ return -EINVAL;
-+}
-+
-+
-+static int ep93xx_ts_ioctl(struct inode *inode, struct file *file, uint command, ulong u)
-+{
-+ static const int version = EV_VERSION;
-+ static const u_int32_t bit =(1 << EV_ABS);
-+ static const u_int32_t absbit = (1 << ABS_X) | (1 << ABS_Y) | (1 << ABS_PRESSURE);
-+ int iReturn ;
-+ int i = 0;
-+
-+ switch(command)
-+ {
-+ case EVIOCGVERSION:
-+ i = copy_to_user((void __user *)u, (void *)version, sizeof(version));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(0,sizeof(u_int32_t) * 8) :
-+ i = copy_to_user((void __user *)u, (void *)bit, sizeof(bit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(EV_ABS, sizeof(absbit) * 8):
-+ i = copy_to_user((void __user *)u, (void *)absbit, sizeof(absbit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+ default:
-+ iReturn = -1;
-+ break;
-+ }
-+
-+ return iReturn;
-+}
-+
-+static struct file_operations ep93xx_ts_fops = {
-+ owner: THIS_MODULE,
-+ read: ep93xx_ts_read,
-+ write: ep93xx_ts_write,
-+ poll: ep93xx_ts_poll,
-+ open: ep93xx_ts_open,
-+ unlocked_ioctl: ep93xx_ts_ioctl,
-+ release: ep93xx_ts_release,
-+ fasync: ep93xx_ts_fasync,
-+};
-+
-+static struct miscdevice ep93xx_ts_miscdev =
-+{
-+ EP93XX_TS_MINOR,
-+ "ep93xx_ts",
-+ &ep93xx_ts_fops
-+};
-+
-+void ep93xx_ts_setup(void)
-+{
-+ unsigned int uiKTDIV, uiTSXYMaxMin;
-+
-+ /*
-+ * Set the TSEN bit in KTDIV so that we are enabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV |= EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+ /*
-+ * Program the EP93XX_TOUCHSCREEN_SETUP and TSSetup2 registers.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Set the the touch settings.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DISCHARGE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ1, EP93XX_TOUCHSCREEN_XSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ2, EP93XX_TOUCHSCREEN_YSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDetect, EP93XX_TOUCHSCREEN_DETECT);
-+
-+ /*
-+ * X,YMin set to 0x40 = have to drag that many pixels for a new irq.
-+ * X,YMax set to 0x40 = 1024 pixels is the maximum movement within the
-+ * time scan limit.
-+ */
-+ uiTSXYMaxMin = (50 << TSMAXMIN_XMIN_SHIFT) & TSMAXMIN_XMIN_MASK;
-+ uiTSXYMaxMin |= (50 << TSMAXMIN_YMIN_SHIFT) & TSMAXMIN_YMIN_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_XMAX_SHIFT) & TSMAXMIN_XMAX_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_YMAX_SHIFT) & TSMAXMIN_YMAX_MASK;
-+ __raw_writel(uiTSXYMaxMin, EP93XX_TOUCHSCREEN_XYMAXMIN);
-+
-+ bCurrentPenDown = 0;
-+ bFreshTouchData = 0;
-+ guiLastX = 0;
-+ guiLastY = 0;
-+ guiLastInvPressure = 0xffffff;
-+
-+ /*
-+ * Enable the touch screen scanning engine.
-+ */
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+/*
-+ * ep93xx_ts_shutdown
-+ *
-+ */
-+static void
-+ep93xx_ts_shutdown(void)
-+{
-+ unsigned int uiKTDIV;
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Disable the scanning engine.
-+ */
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Clear the TSEN bit in KTDIV so that we are disabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV &= ~EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+} /* ep93xx_ts_shutdown */
-+
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id)
-+{
-+ switch(sTouch.state)
-+ {
-+ case TS_STATE_STOPPED:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+
-+ /*
-+ * Get the Z1 value for pressure measurement and set up
-+ * the switch register for getting the Z2 measurement.
-+ */
-+ case TS_STATE_Z1:
-+ Set_Timer2_uSec(EP93XX_TS_ADC_DELAY_USEC);
-+ sTouch.uiZ1 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ2);
-+ sTouch.state = TS_STATE_Z2;
-+ break;
-+
-+ /*
-+ * Get the Z2 value for pressure measurement and set up
-+ * the switch register for getting the Y measurement.
-+ */
-+ case TS_STATE_Z2:
-+ sTouch.uiZ2 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiYSample);
-+ sTouch.state = TS_STATE_Y;
-+ break;
-+
-+ /*
-+ * Get the Y value and set up the switch register for
-+ * getting the X measurement.
-+ */
-+ case TS_STATE_Y:
-+ sTouch.uiY = ADCGetData(4, 20);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiXSample);
-+ sTouch.state = TS_STATE_X;
-+ break;
-+
-+ /*
-+ * Read the X value. This is the last of the 4 adc values
-+ * we need so we continue on to process the data.
-+ */
-+ case TS_STATE_X:
-+ Stop_Timer2();
-+
-+ sTouch.uiX = ADCGetData(4, 20);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ sTouch.state = TS_STATE_DONE;
-+
-+ /*
-+ * Process this set of ADC readings.
-+ */
-+ ProcessPointData();
-+
-+ break;
-+
-+ /*
-+ * Shouldn't get here. But if we do, we can recover...
-+ */
-+ case TS_STATE_DONE:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+ }
-+
-+ /*
-+ * Clear the timer2 interrupt.
-+ */
-+ __raw_writel(1, EP93XX_TIMER2_CLEAR);
-+ return(IRQ_HANDLED);
-+}
-+
-+/*---------------------------------------------------------------------
-+ * ProcessPointData
-+ *
-+ * This routine processes the ADC data into usable point data and then
-+ * puts the driver into hw or sw scanning mode before returning.
-+ *
-+ * We calculate inverse pressure (lower number = more pressure) then
-+ * do a hystheresis with the two pressure values 'light' and 'heavy'.
-+ *
-+ * If we are above the light, we have pen up.
-+ * If we are below the heavy we have pen down.
-+ * As long as the pressure stays below the light, pen stays down.
-+ * When we get above the light again, pen goes back up.
-+ *
-+ */
-+static void ProcessPointData(void)
-+{
-+ int bValidPoint = 0;
-+ unsigned int uiXDiff, uiYDiff, uiInvPressureDiff;
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Calculate the current pressure.
-+ */
-+ uiInvPressure = CalculateInvPressure();
-+
-+ /*
-+ * If pen pressure is so light that it is greater than the 'max' setting
-+ * then we consider this to be a pen up.
-+ */
-+ if (uiInvPressure >= TS_LIGHT_INV_PRESSURE)
-+ {
-+ bCurrentPenDown = 0;
-+ ee93xx_ts_evt_add(0, guiLastX, guiLastY, 0);
-+ TS_Hardware_Scan_Mode();
-+ return;
-+ }
-+
-+ /*
-+ * Hysteresis:
-+ * If the pen pressure is hard enough to be less than the 'min' OR
-+ * the pen is already down and is still less than the 'max'...
-+ */
-+ if ((uiInvPressure < TS_HEAVY_INV_PRESSURE) ||
-+ (bCurrentPenDown && (uiInvPressure < TS_LIGHT_INV_PRESSURE)))
-+ {
-+ if (bCurrentPenDown)
-+ {
-+ /*
-+ * If pen was previously down, check the difference between
-+ * the last sample and this one... if the difference between
-+ * samples is too great, ignore the sample.
-+ */
-+ uiXDiff = abs(guiLastX - sTouch.uiX);
-+ uiYDiff = abs(guiLastY - sTouch.uiY);
-+ uiInvPressureDiff = abs(guiLastInvPressure - uiInvPressure);
-+
-+ if (uiXDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiYDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiInvPressureDiff < TS_MAX_VALID_PRESSURE_CHANGE)
-+ {
-+ bValidPoint = 1;
-+ }
-+ }
-+ else
-+ {
-+ bValidPoint = 1;
-+ }
-+
-+ /*
-+ * If either the pen was put down or dragged make a note of it.
-+ */
-+ if (bValidPoint)
-+ {
-+ guiLastX = sTouch.uiX;
-+ guiLastY = sTouch.uiY;
-+ guiLastInvPressure = uiInvPressure;
-+ bCurrentPenDown = 1;
-+ ee93xx_ts_evt_add(1, sTouch.uiX, sTouch.uiY,
-+ 0x7000000 / uiInvPressure);
-+ }
-+
-+ TS_Soft_Scan_Mode();
-+ return;
-+ }
-+
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch)
-+{
-+ unsigned int uiResult;
-+
-+ /*
-+ * Set the switch settings in the direct register.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(uiADCSwitch, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ /*
-+ * Read and throw away the first sample.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+}
-+
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff)
-+{
-+ unsigned int uiResult, uiValue, uiCount, uiLowest, uiHighest, uiSum, uiAve;
-+
-+ do
-+ {
-+ /*
-+ * Initialize our values.
-+ */
-+ uiLowest = 0xfffffff;
-+ uiHighest = 0;
-+ uiSum = 0;
-+
-+ for (uiCount = 0; uiCount < uiSamples; uiCount++)
-+ {
-+ /*
-+ * Read the touch screen four more times and average.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+ uiValue = (uiResult & TSXYRESULT_AD_MASK) >> TSXYRESULT_AD_SHIFT;
-+ uiValue = ((uiValue >> 4) + ((1 + TSXYRESULT_X_MASK)>>1)) & TSXYRESULT_X_MASK;
-+
-+ /*
-+ * Add up the values.
-+ */
-+ uiSum += uiValue;
-+
-+ /*
-+ * Get the lowest and highest values.
-+ */
-+ if (uiValue < uiLowest)
-+ {
-+ uiLowest = uiValue;
-+ }
-+ if (uiValue > uiHighest)
-+ {
-+ uiHighest = uiValue;
-+ }
-+ }
-+ } while ((uiHighest - uiLowest) > uiMaxDiff);
-+
-+ /*
-+ * Calculate the Average value.
-+ */
-+ uiAve = uiSum / uiSamples;
-+
-+ return uiAve;
-+}
-+
-+/*
-+ * CalculateInvPressure
-+ *
-+ * Is the Touch Valid. Touch is not valid if the X or Y value is not
-+ * in range and the pressure is not enough.
-+ *
-+ * Touch resistance can be measured by the following formula:
-+ *
-+ * Rx * X * Z2
-+ * Rtouch = --------- * (-- - 1)
-+ * 4096 Z1
-+ *
-+ * This is simplified in the ration of Rtouch to Rx. The lower the value, the
-+ * higher the pressure.
-+ *
-+ * Z2
-+ * InvPressure = X * (-- - 1)
-+ * Z1
-+ */
-+static unsigned int CalculateInvPressure(void)
-+{
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Check to see if the point is valid.
-+ */
-+ if (sTouch.uiZ1 < MIN_Z1_VALUE)
-+ {
-+ uiInvPressure = 0x10000;
-+ }
-+
-+ /*
-+ * Can omit the pressure calculation if you need to get rid of the division.
-+ */
-+ else
-+ {
-+ uiInvPressure = ((sTouch.uiX * sTouch.uiZ2) / sTouch.uiZ1) - sTouch.uiX;
-+ }
-+
-+ return uiInvPressure;
-+}
-+
-+/*
-+ * TS_Hardware_Scan_Mode
-+ *
-+ * Enables the ep93xx ts scanning engine so that when the pen goes down
-+ * we will get an interrupt.
-+ */
-+static void TS_Hardware_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ /*
-+ * Disable the soft scanning engine.
-+ */
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Clear the TIN (Touchscreen INactive) bit so we can go to
-+ * automatic scanning mode.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg & ~EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+
-+ /*
-+ * Enable the touch screen scanning state machine by setting
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT | TSSETUP_ENABLE, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the flag to show that we are in interrupt mode.
-+ */
-+ gScanningMode = TS_MODE_HARDWARE_SCAN;
-+
-+ /*
-+ * Initialize EP93XX_TOUCHSCREEN_SETUP2 register.
-+ */
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+}
-+
-+/*
-+ * TS_Soft_Scan_Mode
-+ *
-+ * Sets the touch screen to manual polling mode.
-+ */
-+static void TS_Soft_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ if (gScanningMode != TS_MODE_SOFT_SCAN)
-+ {
-+ /*
-+ * Disable the touch screen scanning state machine by clearing
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the TIN bit so we can do manual touchscreen polling.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg | EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+ }
-+
-+ /*
-+ * Set the switch register up for the first ADC reading
-+ */
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ1);
-+
-+ /*
-+ * Initialize our software state machine to know which ADC
-+ * reading to take
-+ */
-+ sTouch.state = TS_STATE_Z1;
-+
-+ /*
-+ * Set the timer so after a mSec or two settling delay it will
-+ * take the first ADC reading.
-+ */
-+ Set_Timer2_uSec(EP93XX_TS_PER_POINT_DELAY_USEC);
-+
-+ /*
-+ * Note that we are in sw scanning mode not hw scanning mode.
-+ */
-+ gScanningMode = TS_MODE_SOFT_SCAN;
-+
-+}
-+
-+static void Set_Timer2_uSec(unsigned int uiDelay_uSec)
-+{
-+ unsigned int uiClockTicks;
-+
-+ /*
-+ * Stop timer 2
-+ */
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+
-+ uiClockTicks = ((uiDelay_uSec * 508) + 999) / 1000;
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_LOAD);
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_VALUE);
-+
-+ /*
-+ * Set up Timer 2 for 508 kHz clock and periodic mode.
-+ */
-+ __raw_writel(0xC8, EP93XX_TIMER2_CONTROL);
-+
-+}
-+
-+static void Stop_Timer2(void)
-+{
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+}
-+
-+/*
-+ * Initialization and exit routines
-+ */
-+int __init ep93xx_ts_init(void)
-+{
-+ int retval;
-+
-+ retval = request_irq(IRQ_EP93XX_TOUCH, ep93xx_ts_isr,
-+ IRQF_DISABLED, "ep93xx_ts", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get touchscreen IRQ\n");
-+ return retval;
-+ }
-+
-+ retval = request_irq(IRQ_EP93XX_TIMER2, ep93xx_timer2_isr,
-+ IRQF_DISABLED, "ep93xx_timer2", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get timer2 IRQ\n");
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ return retval;
-+ }
-+
-+ misc_register(&ep93xx_ts_miscdev);
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ gScanningMode = TS_MODE_UN_INITIALIZED;
-+
-+ printk(KERN_NOTICE "ep93xx touchscreen driver configured for 4-wire operation\n");
-+
-+ return 0;
-+}
-+
-+void __exit ep93xx_ts_exit(void)
-+{
-+ Stop_Timer2();
-+
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ free_irq(IRQ_EP93XX_TIMER2, 0);
-+
-+ misc_deregister(&ep93xx_ts_miscdev);
-+}
-+
-+module_init(ep93xx_ts_init);
-+module_exit(ep93xx_ts_exit);
-+
-+MODULE_DESCRIPTION("Cirrus EP93xx touchscreen driver");
-+MODULE_SUPPORTED_DEVICE("touchscreen/ep93xx");
-+MODULE_LICENSE("GPL");
---- a/arch/arm/mach-ep93xx/core.c
-+++ b/arch/arm/mach-ep93xx/core.c
-@@ -211,6 +211,7 @@ void ep93xx_syscon_swlocked_write(unsign
-
- spin_unlock_irqrestore(&syscon_swlock, flags);
- }
-+EXPORT_SYMBOL(ep93xx_syscon_swlocked_write);
-
- void ep93xx_devcfg_set_clear(unsigned int set_bits, unsigned int clear_bits)
- {
+++ /dev/null
-This enables the mmc-over-spi driver for the Sim.One board, based on Mika's
-patch, which used a GPIO for chip select in stead of the default SFRMOUT pin.
-I've modified it to use the usual SFRMOUT; if you've modified your Sim.One
-board to use a GPIO instead, uncomment and modify
-// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-in the source file.
- -martinwguy, 14 May 2010
-
-From: Mika Westerberg <mika.westerberg@iki.fi>
-Date: Wed, 28 Apr 2010 08:42:46 +0300
-Subject: [PATCH] ep93xx: simone: added board specific SPI support for MMC/SD cards
-
-This includes setting up EGPIOs 0 and 9 for card detection and chip select
-respectively.
-
---- a/arch/arm/mach-ep93xx/simone.c
-+++ b/arch/arm/mach-ep93xx/simone.c
-@@ -20,10 +20,15 @@
- #include <linux/platform_device.h>
- #include <linux/i2c.h>
- #include <linux/i2c-gpio.h>
-+#include <linux/gpio.h>
-+#include <linux/mmc/host.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/mmc_spi.h>
-
- #include <mach/hardware.h>
- #include <linux/platform_data/video-ep93xx.h>
- #include <mach/gpio-ep93xx.h>
-+#include <linux/platform_data/spi-ep93xx.h>
-
- #include <asm/mach-types.h>
- #include <asm/mach/arch.h>
-@@ -40,6 +45,135 @@ static struct ep93xxfb_mach_info __initd
- .flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
- };
-
-+/*
-+ * GPIO lines used for MMC card detection.
-+ */
-+#define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0
-+
-+/*
-+ * If you have hacked your Sim.One to use a GPIO as SD card chip select
-+ * (SD pin 1), uncomment the following line.
-+ * The example, EGPIO15, is on TP17 near the CPU.
-+ */
-+// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-+
-+/*
-+ * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal,
-+ * you can leave these empty and pass NULL as .controller_data.
-+ */
-+
-+#ifdef MMC_CHIP_SELECT_GPIO
-+static int simone_mmc_spi_setup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+ int err;
-+
-+ err = gpio_request(gpio, spi->modalias);
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_output(gpio, 1);
-+ if (err) {
-+ gpio_free(gpio);
-+ return err;
-+ }
-+
-+ return 0;
-+}
-+
-+static void simone_mmc_spi_cleanup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+
-+ gpio_set_value(gpio, 1);
-+ gpio_direction_input(gpio);
-+ gpio_free(gpio);
-+}
-+
-+static void simone_mmc_spi_cs_control(struct spi_device *spi, int value)
-+{
-+ gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-+}
-+
-+static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = {
-+ .setup = simone_mmc_spi_setup,
-+ .cleanup = simone_mmc_spi_cleanup,
-+ .cs_control = simone_mmc_spi_cs_control,
-+};
-+#endif
-+
-+/*
-+ * MMC card detection GPIO setup.
-+ */
-+static int simone_mmc_spi_init(struct device *dev,
-+ irqreturn_t (*irq_handler)(int, void *), void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+ int irq, err;
-+
-+ err = gpio_request(gpio, dev_name(dev));
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_input(gpio);
-+ if (err)
-+ goto fail;
-+
-+ irq = gpio_to_irq(gpio);
-+ if (irq < 0)
-+ goto fail;
-+
-+ err = request_irq(irq, irq_handler, IRQF_TRIGGER_FALLING,
-+ "MMC card detect", mmc);
-+ if (err)
-+ goto fail;
-+
-+ printk(KERN_INFO "%s: using irq %d for MMC card detection\n",
-+ dev_name(dev), irq);
-+
-+ return 0;
-+fail:
-+ gpio_free(gpio);
-+ return err;
-+}
-+
-+static void simone_mmc_spi_exit(struct device *dev, void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+
-+ free_irq(gpio_to_irq(gpio), mmc);
-+ gpio_free(gpio);
-+}
-+
-+static struct mmc_spi_platform_data simone_mmc_spi_data = {
-+ .init = simone_mmc_spi_init,
-+ .exit = simone_mmc_spi_exit,
-+ .detect_delay = 500,
-+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
-+};
-+
-+static struct spi_board_info simone_spi_devices[] __initdata = {
-+ {
-+ .modalias = "mmc_spi",
-+#ifdef MMC_CHIP_SELECT_GPIO
-+ .controller_data = &simone_mmc_spi_ops,
-+#endif
-+ .platform_data = &simone_mmc_spi_data,
-+ /*
-+ * We use 10 MHz even though the maximum is 3.7 MHz. The driver
-+ * will limit it automatically to max. frequency.
-+ */
-+ .max_speed_hz = 10 * 1000 * 1000,
-+ .bus_num = 0,
-+ .chip_select = 0,
-+ .mode = SPI_MODE_3,
-+ },
-+};
-+
-+static struct ep93xx_spi_info simone_spi_info __initdata = {
-+ .num_chipselect = ARRAY_SIZE(simone_spi_devices),
-+};
-+
- static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = {
- .sda_pin = EP93XX_GPIO_LINE_EEDAT,
- .sda_is_open_drain = 0,
-@@ -74,6 +208,8 @@ static void __init simone_init_machine(v
- ep93xx_register_fb(&simone_fb_info);
- ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
- ARRAY_SIZE(simone_i2c_board_info));
-+ ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
-+ ARRAY_SIZE(simone_spi_devices));
- simone_register_audio();
- }
-
+++ /dev/null
-This patch puts the EP93xx chip revision and unique ID into /proc/cpuinfo.
-This is necessary to be able to set a unique MAC address for DHCP purposes
-by adding a line to /etc/network/interfaces:
-
-# Generate a unique locally-assigned MAC address from the CPU serial number
-pre-up ifconfig eth0 hw ether `sed -n 's/^Serial.* 000000/02/p' /proc/cpuinfo`
-
-It uses the chip revision reading code in the ep93xx-chip-revision patch.
-
-Really, this is wrong, since /proc/cpuinfo should report the revision and
-serial number of the ARM920T processor, while these are the rev and serial
-of the EP93xx SoC. In a future kernel (>2.6.34) there may be a new file
-/proc/socinfo for this information.
-
- -martinwguy 14 May 2010
-
---- a/arch/arm/kernel/setup.c
-+++ b/arch/arm/kernel/setup.c
-@@ -55,6 +55,12 @@
- #include <asm/memblock.h>
- #include <asm/virt.h>
-
-+#if defined(CONFIG_ARCH_EP93XX)
-+#include <asm/io.h>
-+#include <mach/platform.h>
-+#include <mach/ep93xx-regs.h>
-+#endif
-+
- #include "atags.h"
- #include "tcm.h"
-
-@@ -903,9 +909,16 @@ static int c_show(struct seq_file *m, vo
- }
-
- seq_printf(m, "Hardware\t: %s\n", machine_name);
-+#if defined(CONFIG_ARCH_EP93XX)
-+ seq_printf(m, "Revision\t: %04x\n",
-+ ep93xx_chip_revision());
-+ seq_printf(m, "Serial\t\t: %016x\n",
-+ *((unsigned int *)EP93XX_SECURITY_UNIQID));
-+#else
- seq_printf(m, "Revision\t: %04x\n", system_rev);
- seq_printf(m, "Serial\t\t: %08x%08x\n",
- system_serial_high, system_serial_low);
-+#endif
-
- return 0;
- }
---- a/arch/arm/mach-ep93xx/soc.h
-+++ b/arch/arm/mach-ep93xx/soc.h
-@@ -82,8 +82,6 @@
- #define EP93XX_I2S_PHYS_BASE EP93XX_APB_PHYS(0x00020000)
- #define EP93XX_I2S_BASE EP93XX_APB_IOMEM(0x00020000)
-
--#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
--
- #define EP93XX_AAC_PHYS_BASE EP93XX_APB_PHYS(0x00080000)
- #define EP93XX_AAC_BASE EP93XX_APB_IOMEM(0x00080000)
-
---- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
-@@ -38,4 +38,8 @@
- #define EP93XX_UART3_PHYS_BASE EP93XX_APB_PHYS(0x000e0000)
- #define EP93XX_UART3_BASE EP93XX_APB_IOMEM(0x000e0000)
-
-+#define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000)
-+#define EP93XX_SECURITY_REG(x) (EP93XX_SECURITY_BASE + (x))
-+#define EP93XX_SECURITY_UNIQID EP93XX_SECURITY_REG(0x2440)
-+
- #endif
+++ /dev/null
----
- arch/arm/mach-ep93xx/include/mach/hardware.h | 1
- arch/arm/mach-ep93xx/include/mach/regs_touch.h | 95 ++
- drivers/input/touchscreen/Kconfig | 5
- drivers/input/touchscreen/Makefile | 1
- drivers/input/touchscreen/ep93xx_ts.c | 1117 +++++++++++++++++++++++++
- drivers/input/touchscreen/ep93xx_ts.h | 53 +
- 6 files changed, 1272 insertions(+)
-
---- a/drivers/input/touchscreen/Kconfig
-+++ b/drivers/input/touchscreen/Kconfig
-@@ -235,6 +235,15 @@ config TOUCHSCREEN_EGALAX
- To compile this driver as a module, choose M here: the
- module will be called egalax_ts.
-
-+config TOUCHSCREEN_EP93XX
-+ tristate "EP93xx Touchscreen"
-+ depends on ARM && INPUT && ARCH_EP93XX
-+ help
-+ Say Y here to enable support for EP93xx touch screen.
-+
-+ To compile this driver as a module, choose M here:
-+ the module will be called ep93xx_ts.
-+
- config TOUCHSCREEN_FUJITSU
- tristate "Fujitsu serial touchscreen"
- select SERIO
---- a/drivers/input/touchscreen/Makefile
-+++ b/drivers/input/touchscreen/Makefile
-@@ -29,6 +29,7 @@ obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunz
- obj-$(CONFIG_TOUCHSCREEN_EETI) += eeti_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
- obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o
-+obj-$(CONFIG_TOUCHSCREEN_EP93XX) += ep93xx_ts.o
- obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
- obj-$(CONFIG_TOUCHSCREEN_ILI210X) += ili210x.o
- obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
---- /dev/null
-+++ b/drivers/input/touchscreen/ep93xx_ts.c
-@@ -0,0 +1,1022 @@
-+/*
-+ * linux/drivers/input/touchscreen/ep93xx_ts.c
-+ *
-+ * Copyright (C) 2003-2004 Cirrus Corp.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/delay.h>
-+#include <linux/wait.h>
-+#include <linux/fs.h>
-+#include <linux/sched.h>
-+#include <linux/poll.h>
-+#include <linux/miscdevice.h>
-+#include <linux/init.h>
-+#include <linux/compiler.h>
-+#include <linux/timer.h>
-+#include <linux/interrupt.h>
-+#include <linux/syscalls.h>
-+#include <linux/input.h>
-+#include <linux/semaphore.h>
-+#include <asm/irq.h>
-+#include <mach/hardware.h>
-+#include <asm/io.h>
-+#include "../../../arch/arm/mach-ep93xx/soc.h"
-+
-+/* This stuff should be in ep93xx-regs.h */
-+#define EP93XX_TOUCHSCREEN_REG(x) (EP93XX_TOUCHSCREEN_BASE + (x))
-+/* R/W touchscreen controller setup control register. */
-+#define EP93XX_TOUCHSCREEN_SETUP EP93XX_TOUCHSCREEN_REG(0x00)
-+/* R/W touchscreen controller max/min register. */
-+#define EP93XX_TOUCHSCREEN_XYMAXMIN EP93XX_TOUCHSCREEN_REG(0x04)
-+/* R touchscreen controller result register. */
-+#define EP93XX_TOUCHSCREEN_XYRESULT EP93XX_TOUCHSCREEN_REG(0x08)
-+/* LOCKED R/W touchscreen Switch Matrix control register. */
-+#define EP93XX_TOUCHSCREEN_DISCHARGE EP93XX_TOUCHSCREEN_REG(0x0C)
-+#define EP93XX_TOUCHSCREEN_XSAMPLE EP93XX_TOUCHSCREEN_REG(0x10)
-+#define EP93XX_TOUCHSCREEN_YSAMPLE EP93XX_TOUCHSCREEN_REG(0x14)
-+#define EP93XX_TOUCHSCREEN_DIRECT EP93XX_TOUCHSCREEN_REG(0x18)
-+#define EP93XX_TOUCHSCREEN_DETECT EP93XX_TOUCHSCREEN_REG(0x1C)
-+/* NA R/W touchscreen software lock register. */
-+#define EP93XX_TOUCHSCREEN_SWLOCK EP93XX_TOUCHSCREEN_REG(0x20)
-+/* R/W touchscreen setup control register #2. */
-+#define EP93XX_TOUCHSCREEN_SETUP2 EP93XX_TOUCHSCREEN_REG(0x24)
-+
-+/* These are duplicated in mach-ep93xx/core.c */
-+#define EP93XX_TIMER_REG(x) (EP93XX_TIMER_BASE + (x))
-+#define EP93XX_TIMER2_LOAD EP93XX_TIMER_REG(0x20)
-+#define EP93XX_TIMER2_VALUE EP93XX_TIMER_REG(0x24)
-+#define EP93XX_TIMER2_CONTROL EP93XX_TIMER_REG(0x28)
-+#define EP93XX_TIMER2_CLEAR EP93XX_TIMER_REG(0x2c)
-+
-+/*
-+ * Register bit definitions
-+ */
-+#define TSSETUP_SDLY_MASK 0x000003FF
-+#define TSSETUP_SDLY_SHIFT 0
-+#define TSSETUP_NSMP_4 0x00000000
-+#define TSSETUP_NSMP_8 0x00000400
-+#define TSSETUP_NSMP_16 0x00000800
-+#define TSSETUP_NSMP_32 0x00000C00
-+#define TSSETUP_NSMP_MASK 0x00000C00
-+#define TSSETUP_DEV_4 0x00000000
-+#define TSSETUP_DEV_8 0x00001000
-+#define TSSETUP_DEV_12 0x00002000
-+#define TSSETUP_DEV_16 0x00003000
-+#define TSSETUP_DEV_24 0x00004000
-+#define TSSETUP_DEV_32 0x00005000
-+#define TSSETUP_DEV_64 0x00006000
-+#define TSSETUP_DEV_128 0x00007000
-+#define TSSETUP_ENABLE 0x00008000
-+#define TSSETUP_DLY_MASK 0x03FF0000
-+#define TSSETUP_DLY_SHIFT 16
-+#define TSSETUP_TDTCT 0x80000000
-+
-+#define TSMAXMIN_XMIN_MASK 0x000000FF
-+#define TSMAXMIN_XMIN_SHIFT 0
-+#define TSMAXMIN_YMIN_MASK 0x0000FF00
-+#define TSMAXMIN_YMIN_SHIFT 8
-+#define TSMAXMIN_XMAX_MASK 0x00FF0000
-+#define TSMAXMIN_XMAX_SHIFT 16
-+#define TSMAXMIN_YMAX_MASK 0xFF000000
-+#define TSMAXMIN_YMAX_SHIFT 24
-+
-+#define TSXYRESULT_X_MASK 0x00000FFF
-+#define TSXYRESULT_X_SHIFT 0
-+#define TSXYRESULT_AD_MASK 0x0000FFFF
-+#define TSXYRESULT_AD_SHIFT 0
-+#define TSXYRESULT_Y_MASK 0x0FFF0000
-+#define TSXYRESULT_Y_SHIFT 16
-+#define TSXYRESULT_SDR 0x80000000
-+
-+#define TSX_SAMPLE_MASK 0x00003FFF
-+#define TSX_SAMPLE_SHIFT 0x00
-+#define TSY_SAMPLE_MASK 0x3FFF0000
-+#define TSY_SAMPLE_SHIFT 0x10
-+
-+#define TSSETUP2_TINT 0x00000001
-+#define TSSETUP2_NICOR 0x00000002
-+#define TSSETUP2_PINT 0x00000004
-+#define TSSETUP2_PENSTS 0x00000008
-+#define TSSETUP2_PINTEN 0x00000010
-+#define TSSETUP2_DEVINT 0x00000020
-+#define TSSETUP2_DINTEN 0x00000040
-+#define TSSETUP2_DTMEN 0x00000080
-+#define TSSETUP2_DISDEV 0x00000100
-+#define TSSETUP2_NSIGND 0x00000200
-+#define TSSETUP2_S28EN 0x00000400
-+#define TSSETUP2_RINTEN 0x00000800
-+
-+#define TSXYRESULT_SDR 0x80000000
-+
-+/*
-+ * These are used as trigger levels to know when we have pen up/down.
-+ * The rules:
-+ * 1. TS_HEAVY_INV_PRESSURE < TS_LIGHT_INV_PRESSURE because these
-+ * are Inverse pressure.
-+ * 2. Any touch lighter than TS_LIGHT_INV_PRESSURE is a pen up.
-+ * 3. Any touch heavier than TS_HEAVY_INV_PRESSURE is a pen down.
-+ */
-+#define TS_HEAVY_INV_PRESSURE 0xFE0 /* C00 */
-+#define TS_LIGHT_INV_PRESSURE 0xFFF /* e00 */
-+
-+/*
-+ * If the x, y, or inverse pressure changes more than these values
-+ * between two succeeding points, the point is not reported.
-+ */
-+#define TS_MAX_VALID_XY_CHANGE 0x300
-+#define TS_MAX_VALID_PRESSURE_CHANGE 0x100
-+
-+/*
-+ * This is the minimum Z1 Value that is valid.
-+ */
-+#define MIN_Z1_VALUE 0x50
-+
-+/*
-+ * Settling delay for taking each ADC measurement. Increase this
-+ * if ts is jittery.
-+ */
-+#define EP93XX_TS_ADC_DELAY_USEC 2000
-+
-+/*
-+ * Delay between TS points.
-+ */
-+#define EP93XX_TS_PER_POINT_DELAY_USEC 10000
-+
-+/*
-+ * A few more macros...
-+ */
-+#define TSSETUP_DEFAULT (TSSETUP_NSMP_32 | TSSETUP_DEV_64 | \
-+ ((128<<TSSETUP_SDLY_SHIFT) & TSSETUP_SDLY_MASK) | \
-+ ((128<<TSSETUP_DLY_SHIFT) & TSSETUP_DLY_MASK))
-+
-+#define TSSETUP2_DEFAULT (TSSETUP2_NSIGND)
-+
-+/*
-+ * For now, we use one of the minor numbers from the local/experimental
-+ * range.
-+ */
-+#define EP93XX_TS_MINOR 240
-+
-+/*
-+ * Static Declarations
-+ */
-+static unsigned int guiLastX, guiLastY;
-+static unsigned int guiLastInvPressure;
-+
-+struct TouchScreenSample
-+{
-+ int currentX;
-+ int currentY;
-+ int currentButton;
-+ int currentPressure;
-+ struct timeval currentTime;
-+};
-+
-+/*
-+ * This must match the structure in tslib.
-+ */
-+struct ts_sample {
-+ int x;
-+ int y;
-+ unsigned int pressure;
-+ struct timeval tv;
-+};
-+
-+static struct TouchScreenSample gSample;
-+static int bFreshTouchData;
-+static int bCurrentPenDown;
-+
-+static DECLARE_WAIT_QUEUE_HEAD(queue);
-+static DEFINE_SEMAPHORE(open_sem);
-+static DEFINE_SPINLOCK(event_buffer_lock);
-+static struct fasync_struct *ep93xx_fasync;
-+
-+/*
-+ * Typedef Declarations
-+ */
-+typedef enum {
-+ TS_MODE_UN_INITIALIZED,
-+ TS_MODE_HARDWARE_SCAN,
-+ TS_MODE_SOFT_SCAN
-+} ts_mode_t;
-+
-+static ts_mode_t gScanningMode;
-+
-+typedef enum{
-+ TS_STATE_STOPPED = 0,
-+ TS_STATE_Z1,
-+ TS_STATE_Z2,
-+ TS_STATE_Y,
-+ TS_STATE_X,
-+ TS_STATE_DONE
-+} ts_states_t;
-+
-+typedef struct
-+{
-+ unsigned int uiX;
-+ unsigned int uiY;
-+ unsigned int uiZ1;
-+ unsigned int uiZ2;
-+ ts_states_t state;
-+} ts_struct_t;
-+
-+static ts_struct_t sTouch;
-+
-+/*
-+ * From the spec, here's how to set up the touch screen's switch registers.
-+ */
-+typedef struct
-+{
-+ unsigned int uiDetect;
-+ unsigned int uiDischarge;
-+ unsigned int uiXSample;
-+ unsigned int uiYSample;
-+ unsigned int uiSwitchZ1;
-+ unsigned int uiSwitchZ2;
-+}SwitchStructType;
-+
-+/*
-+ * Here's the switch settings for a 4-wire touchscreen. See the spec
-+ * for how to handle a 4, 7, or 8-wire.
-+ */
-+const static SwitchStructType sSwitchSettings =
-+/* s28en=0 */
-+/* TSDetect TSDischarge TSXSample TSYSample SwitchZ1 SwitchZ2 */
-+ {0x00403604, 0x0007fe04, 0x00081604, 0x00104601, 0x00101601, 0x00101608};
-+
-+/*
-+ * Function declarations
-+ */
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch);
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id);
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id);
-+static void ee93xx_ts_evt_add(int button, int dX, int dY, int Pressure);
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf,
-+ size_t count, loff_t *l);
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait);
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp);
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on);
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp);
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer,
-+ size_t count, loff_t *ppos);
-+static void ep93xx_ts_setup(void);
-+static void ep93xx_ts_shutdown(void);
-+int __init ep93xx_ts_init(void);
-+void __exit ep93xx_ts_exit(void);
-+static unsigned int CalculateInvPressure(void);
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff);
-+static void TS_Soft_Scan_Mode(void);
-+static void TS_Hardware_Scan_Mode(void);
-+static void ProcessPointData(void);
-+static void Set_Timer2_uSec(unsigned int Delay_mSec);
-+static void Stop_Timer2(void);
-+
-+/*
-+ * ep93xx_ts_isr
-+ */
-+static irqreturn_t ep93xx_ts_isr(int irq, void *dev_id)
-+{
-+ /*
-+ * Note that we don't clear the interrupt here. The interrupt
-+ * gets cleared in TS_Soft_Scan_Mode when the TS ENABLE
-+ * bit is cleared.
-+ */
-+
-+ /*
-+ * Set the ts to manual polling mode and schedule a callback.
-+ * That way we can return from the isr in a reasonable amount of
-+ * time and process the touch in the callback after a brief delay.
-+ */
-+ TS_Soft_Scan_Mode();
-+
-+ return(IRQ_HANDLED);
-+}
-+
-+/*
-+ * Save the current ts 'event' in an atomic fashion.
-+ */
-+static void ee93xx_ts_evt_add(int buttons, int iX, int iY, int iPressure)
-+{
-+ /*
-+ * Note the event, but use spinlocks to keep it from getting
-+ * halfway read if we get interrupted.
-+ */
-+
-+ spin_lock(&event_buffer_lock);
-+
-+ gSample.currentX = iX;
-+ gSample.currentY = iY;
-+ gSample.currentButton = buttons;
-+ gSample.currentPressure = iPressure;
-+ bFreshTouchData = 1;
-+ do_gettimeofday(&gSample.currentTime);
-+
-+ spin_unlock(&event_buffer_lock);
-+
-+ kill_fasync(&ep93xx_fasync, SIGIO, POLL_IN);
-+ wake_up_interruptible(&queue);
-+}
-+
-+
-+static ssize_t ep93xx_ts_read(struct file *filp, char *buf, size_t count, loff_t *l)
-+{
-+ unsigned short data[3];
-+ struct ts_sample ts_data;
-+ int iReturn = -EFAULT;
-+
-+ if (!bFreshTouchData)
-+ {
-+ iReturn = 0;
-+ }
-+ else if (count == sizeof(data))
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ data[0] = gSample.currentX;
-+ data[1] = gSample.currentY;
-+ data[2] = gSample.currentButton;
-+
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, data, sizeof data))
-+ return -EFAULT;
-+
-+ count -= sizeof(data);
-+
-+ /* return the # of bytes that got read */
-+ iReturn = sizeof(data) ;
-+ }
-+ else if (count == sizeof(struct ts_sample) )
-+ {
-+ spin_lock_irq(&event_buffer_lock);
-+ bFreshTouchData = 0;
-+ ts_data.x = gSample.currentX;
-+ ts_data.y = gSample.currentY;
-+ ts_data.pressure = gSample.currentPressure;
-+ ts_data.tv = gSample.currentTime;
-+ spin_unlock_irq(&event_buffer_lock);
-+
-+ if (copy_to_user(buf, &ts_data, sizeof(struct ts_sample)))
-+ {
-+ iReturn = -EFAULT;
-+ }
-+ else
-+ {
-+ count -= sizeof(ts_data);
-+ iReturn = sizeof(ts_data);
-+ }
-+ }
-+
-+ return iReturn;
-+}
-+
-+static unsigned int ep93xx_ts_poll(struct file *filp, poll_table *wait)
-+{
-+ poll_wait(filp, &queue, wait);
-+
-+ if (bFreshTouchData)
-+ {
-+ return POLLIN | POLLRDNORM;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_open(struct inode *inode, struct file *filp)
-+{
-+ if (down_trylock(&open_sem))
-+ {
-+ return -EBUSY;
-+ }
-+
-+ ep93xx_ts_setup();
-+
-+ return 0;
-+}
-+
-+/*
-+ * Asynchronous I/O support.
-+ */
-+static int ep93xx_ts_fasync(int fd, struct file *filp, int on)
-+{
-+ int retval;
-+
-+ retval = fasync_helper(fd, filp, on, &ep93xx_fasync);
-+ if (retval < 0)
-+ {
-+ return retval;
-+ }
-+
-+ return 0;
-+}
-+
-+static int ep93xx_ts_release(struct inode *inode, struct file *filp)
-+{
-+ Stop_Timer2();
-+
-+ /*
-+ * Call our async I/O support to request that this file
-+ * cease to be used for async I/O.
-+ */
-+ ep93xx_ts_fasync(-1, filp, 0);
-+
-+ ep93xx_ts_shutdown();
-+
-+ up(&open_sem);
-+
-+ return 0;
-+}
-+
-+static ssize_t ep93xx_ts_write(struct file *file, const char *buffer, size_t count,
-+ loff_t *ppos)
-+{
-+ return -EINVAL;
-+}
-+
-+
-+static int ep93xx_ts_ioctl(struct inode *inode, struct file *file, uint command, ulong u)
-+{
-+ static const int version = EV_VERSION;
-+ static const u_int32_t bit =(1 << EV_ABS);
-+ static const u_int32_t absbit = (1 << ABS_X) | (1 << ABS_Y) | (1 << ABS_PRESSURE);
-+ int iReturn ;
-+ int i = 0;
-+
-+ switch(command)
-+ {
-+ case EVIOCGVERSION:
-+ i = copy_to_user((void __user *)u, (void *)version, sizeof(version));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(0,sizeof(u_int32_t) * 8) :
-+ i = copy_to_user((void __user *)u, (void *)bit, sizeof(bit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+
-+ case EVIOCGBIT(EV_ABS, sizeof(absbit) * 8):
-+ i = copy_to_user((void __user *)u, (void *)absbit, sizeof(absbit));
-+ iReturn = i ? -EFAULT : 0;
-+ break;
-+ default:
-+ iReturn = -1;
-+ break;
-+ }
-+
-+ return iReturn;
-+}
-+
-+static struct file_operations ep93xx_ts_fops = {
-+ owner: THIS_MODULE,
-+ read: ep93xx_ts_read,
-+ write: ep93xx_ts_write,
-+ poll: ep93xx_ts_poll,
-+ open: ep93xx_ts_open,
-+ unlocked_ioctl: ep93xx_ts_ioctl,
-+ release: ep93xx_ts_release,
-+ fasync: ep93xx_ts_fasync,
-+};
-+
-+static struct miscdevice ep93xx_ts_miscdev =
-+{
-+ EP93XX_TS_MINOR,
-+ "ep93xx_ts",
-+ &ep93xx_ts_fops
-+};
-+
-+void ep93xx_ts_setup(void)
-+{
-+ unsigned int uiKTDIV, uiTSXYMaxMin;
-+
-+ /*
-+ * Set the TSEN bit in KTDIV so that we are enabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV |= EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+ /*
-+ * Program the EP93XX_TOUCHSCREEN_SETUP and TSSetup2 registers.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Set the the touch settings.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DISCHARGE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ1, EP93XX_TOUCHSCREEN_XSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiSwitchZ2, EP93XX_TOUCHSCREEN_YSAMPLE);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDetect, EP93XX_TOUCHSCREEN_DETECT);
-+
-+ /*
-+ * X,YMin set to 0x40 = have to drag that many pixels for a new irq.
-+ * X,YMax set to 0x40 = 1024 pixels is the maximum movement within the
-+ * time scan limit.
-+ */
-+ uiTSXYMaxMin = (50 << TSMAXMIN_XMIN_SHIFT) & TSMAXMIN_XMIN_MASK;
-+ uiTSXYMaxMin |= (50 << TSMAXMIN_YMIN_SHIFT) & TSMAXMIN_YMIN_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_XMAX_SHIFT) & TSMAXMIN_XMAX_MASK;
-+ uiTSXYMaxMin |= (0xff << TSMAXMIN_YMAX_SHIFT) & TSMAXMIN_YMAX_MASK;
-+ __raw_writel(uiTSXYMaxMin, EP93XX_TOUCHSCREEN_XYMAXMIN);
-+
-+ bCurrentPenDown = 0;
-+ bFreshTouchData = 0;
-+ guiLastX = 0;
-+ guiLastY = 0;
-+ guiLastInvPressure = 0xffffff;
-+
-+ /*
-+ * Enable the touch screen scanning engine.
-+ */
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+/*
-+ * ep93xx_ts_shutdown
-+ *
-+ */
-+static void
-+ep93xx_ts_shutdown(void)
-+{
-+ unsigned int uiKTDIV;
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Disable the scanning engine.
-+ */
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP);
-+ __raw_writel(0, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+ /*
-+ * Clear the TSEN bit in KTDIV so that we are disabling the clock
-+ * for the touchscreen.
-+ */
-+ uiKTDIV = __raw_readl(EP93XX_SYSCON_KEYTCHCLKDIV);
-+ uiKTDIV &= ~EP93XX_SYSCON_KEYTCHCLKDIV_TSEN;
-+ ep93xx_syscon_swlocked_write(uiKTDIV, EP93XX_SYSCON_KEYTCHCLKDIV);
-+
-+} /* ep93xx_ts_shutdown */
-+
-+static irqreturn_t ep93xx_timer2_isr(int irq, void *dev_id)
-+{
-+ switch(sTouch.state)
-+ {
-+ case TS_STATE_STOPPED:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+
-+ /*
-+ * Get the Z1 value for pressure measurement and set up
-+ * the switch register for getting the Z2 measurement.
-+ */
-+ case TS_STATE_Z1:
-+ Set_Timer2_uSec(EP93XX_TS_ADC_DELAY_USEC);
-+ sTouch.uiZ1 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ2);
-+ sTouch.state = TS_STATE_Z2;
-+ break;
-+
-+ /*
-+ * Get the Z2 value for pressure measurement and set up
-+ * the switch register for getting the Y measurement.
-+ */
-+ case TS_STATE_Z2:
-+ sTouch.uiZ2 = ADCGetData(2, 200);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiYSample);
-+ sTouch.state = TS_STATE_Y;
-+ break;
-+
-+ /*
-+ * Get the Y value and set up the switch register for
-+ * getting the X measurement.
-+ */
-+ case TS_STATE_Y:
-+ sTouch.uiY = ADCGetData(4, 20);
-+ ep93xx_ts_set_direct(sSwitchSettings.uiXSample);
-+ sTouch.state = TS_STATE_X;
-+ break;
-+
-+ /*
-+ * Read the X value. This is the last of the 4 adc values
-+ * we need so we continue on to process the data.
-+ */
-+ case TS_STATE_X:
-+ Stop_Timer2();
-+
-+ sTouch.uiX = ADCGetData(4, 20);
-+
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(sSwitchSettings.uiDischarge, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ sTouch.state = TS_STATE_DONE;
-+
-+ /*
-+ * Process this set of ADC readings.
-+ */
-+ ProcessPointData();
-+
-+ break;
-+
-+ /*
-+ * Shouldn't get here. But if we do, we can recover...
-+ */
-+ case TS_STATE_DONE:
-+ TS_Hardware_Scan_Mode();
-+ break;
-+ }
-+
-+ /*
-+ * Clear the timer2 interrupt.
-+ */
-+ __raw_writel(1, EP93XX_TIMER2_CLEAR);
-+ return(IRQ_HANDLED);
-+}
-+
-+/*---------------------------------------------------------------------
-+ * ProcessPointData
-+ *
-+ * This routine processes the ADC data into usable point data and then
-+ * puts the driver into hw or sw scanning mode before returning.
-+ *
-+ * We calculate inverse pressure (lower number = more pressure) then
-+ * do a hystheresis with the two pressure values 'light' and 'heavy'.
-+ *
-+ * If we are above the light, we have pen up.
-+ * If we are below the heavy we have pen down.
-+ * As long as the pressure stays below the light, pen stays down.
-+ * When we get above the light again, pen goes back up.
-+ *
-+ */
-+static void ProcessPointData(void)
-+{
-+ int bValidPoint = 0;
-+ unsigned int uiXDiff, uiYDiff, uiInvPressureDiff;
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Calculate the current pressure.
-+ */
-+ uiInvPressure = CalculateInvPressure();
-+
-+ /*
-+ * If pen pressure is so light that it is greater than the 'max' setting
-+ * then we consider this to be a pen up.
-+ */
-+ if (uiInvPressure >= TS_LIGHT_INV_PRESSURE)
-+ {
-+ bCurrentPenDown = 0;
-+ ee93xx_ts_evt_add(0, guiLastX, guiLastY, 0);
-+ TS_Hardware_Scan_Mode();
-+ return;
-+ }
-+
-+ /*
-+ * Hysteresis:
-+ * If the pen pressure is hard enough to be less than the 'min' OR
-+ * the pen is already down and is still less than the 'max'...
-+ */
-+ if ((uiInvPressure < TS_HEAVY_INV_PRESSURE) ||
-+ (bCurrentPenDown && (uiInvPressure < TS_LIGHT_INV_PRESSURE)))
-+ {
-+ if (bCurrentPenDown)
-+ {
-+ /*
-+ * If pen was previously down, check the difference between
-+ * the last sample and this one... if the difference between
-+ * samples is too great, ignore the sample.
-+ */
-+ uiXDiff = abs(guiLastX - sTouch.uiX);
-+ uiYDiff = abs(guiLastY - sTouch.uiY);
-+ uiInvPressureDiff = abs(guiLastInvPressure - uiInvPressure);
-+
-+ if (uiXDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiYDiff < TS_MAX_VALID_XY_CHANGE
-+ && uiInvPressureDiff < TS_MAX_VALID_PRESSURE_CHANGE)
-+ {
-+ bValidPoint = 1;
-+ }
-+ }
-+ else
-+ {
-+ bValidPoint = 1;
-+ }
-+
-+ /*
-+ * If either the pen was put down or dragged make a note of it.
-+ */
-+ if (bValidPoint)
-+ {
-+ guiLastX = sTouch.uiX;
-+ guiLastY = sTouch.uiY;
-+ guiLastInvPressure = uiInvPressure;
-+ bCurrentPenDown = 1;
-+ ee93xx_ts_evt_add(1, sTouch.uiX, sTouch.uiY,
-+ 0x7000000 / uiInvPressure);
-+ }
-+
-+ TS_Soft_Scan_Mode();
-+ return;
-+ }
-+
-+ TS_Hardware_Scan_Mode();
-+}
-+
-+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch)
-+{
-+ unsigned int uiResult;
-+
-+ /*
-+ * Set the switch settings in the direct register.
-+ */
-+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK);
-+ __raw_writel(uiADCSwitch, EP93XX_TOUCHSCREEN_DIRECT);
-+
-+ /*
-+ * Read and throw away the first sample.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+}
-+
-+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff)
-+{
-+ unsigned int uiResult, uiValue, uiCount, uiLowest, uiHighest, uiSum, uiAve;
-+
-+ do
-+ {
-+ /*
-+ * Initialize our values.
-+ */
-+ uiLowest = 0xfffffff;
-+ uiHighest = 0;
-+ uiSum = 0;
-+
-+ for (uiCount = 0; uiCount < uiSamples; uiCount++)
-+ {
-+ /*
-+ * Read the touch screen four more times and average.
-+ */
-+ do {
-+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT);
-+ } while (!(uiResult & TSXYRESULT_SDR));
-+
-+ uiValue = (uiResult & TSXYRESULT_AD_MASK) >> TSXYRESULT_AD_SHIFT;
-+ uiValue = ((uiValue >> 4) + ((1 + TSXYRESULT_X_MASK)>>1)) & TSXYRESULT_X_MASK;
-+
-+ /*
-+ * Add up the values.
-+ */
-+ uiSum += uiValue;
-+
-+ /*
-+ * Get the lowest and highest values.
-+ */
-+ if (uiValue < uiLowest)
-+ {
-+ uiLowest = uiValue;
-+ }
-+ if (uiValue > uiHighest)
-+ {
-+ uiHighest = uiValue;
-+ }
-+ }
-+ } while ((uiHighest - uiLowest) > uiMaxDiff);
-+
-+ /*
-+ * Calculate the Average value.
-+ */
-+ uiAve = uiSum / uiSamples;
-+
-+ return uiAve;
-+}
-+
-+/*
-+ * CalculateInvPressure
-+ *
-+ * Is the Touch Valid. Touch is not valid if the X or Y value is not
-+ * in range and the pressure is not enough.
-+ *
-+ * Touch resistance can be measured by the following formula:
-+ *
-+ * Rx * X * Z2
-+ * Rtouch = --------- * (-- - 1)
-+ * 4096 Z1
-+ *
-+ * This is simplified in the ration of Rtouch to Rx. The lower the value, the
-+ * higher the pressure.
-+ *
-+ * Z2
-+ * InvPressure = X * (-- - 1)
-+ * Z1
-+ */
-+static unsigned int CalculateInvPressure(void)
-+{
-+ unsigned int uiInvPressure;
-+
-+ /*
-+ * Check to see if the point is valid.
-+ */
-+ if (sTouch.uiZ1 < MIN_Z1_VALUE)
-+ {
-+ uiInvPressure = 0x10000;
-+ }
-+
-+ /*
-+ * Can omit the pressure calculation if you need to get rid of the division.
-+ */
-+ else
-+ {
-+ uiInvPressure = ((sTouch.uiX * sTouch.uiZ2) / sTouch.uiZ1) - sTouch.uiX;
-+ }
-+
-+ return uiInvPressure;
-+}
-+
-+/*
-+ * TS_Hardware_Scan_Mode
-+ *
-+ * Enables the ep93xx ts scanning engine so that when the pen goes down
-+ * we will get an interrupt.
-+ */
-+static void TS_Hardware_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ /*
-+ * Disable the soft scanning engine.
-+ */
-+ sTouch.state = TS_STATE_STOPPED;
-+ Stop_Timer2();
-+
-+ /*
-+ * Clear the TIN (Touchscreen INactive) bit so we can go to
-+ * automatic scanning mode.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg & ~EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+
-+ /*
-+ * Enable the touch screen scanning state machine by setting
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT | TSSETUP_ENABLE, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the flag to show that we are in interrupt mode.
-+ */
-+ gScanningMode = TS_MODE_HARDWARE_SCAN;
-+
-+ /*
-+ * Initialize EP93XX_TOUCHSCREEN_SETUP2 register.
-+ */
-+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2);
-+
-+}
-+
-+/*
-+ * TS_Soft_Scan_Mode
-+ *
-+ * Sets the touch screen to manual polling mode.
-+ */
-+static void TS_Soft_Scan_Mode(void)
-+{
-+ unsigned int uiDevCfg;
-+
-+ if (gScanningMode != TS_MODE_SOFT_SCAN)
-+ {
-+ /*
-+ * Disable the touch screen scanning state machine by clearing
-+ * the ENABLE bit.
-+ */
-+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP);
-+
-+ /*
-+ * Set the TIN bit so we can do manual touchscreen polling.
-+ */
-+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG);
-+ ep93xx_syscon_swlocked_write(uiDevCfg | EP93XX_SYSCON_DEVCFG_TIN,
-+ EP93XX_SYSCON_DEVCFG);
-+ }
-+
-+ /*
-+ * Set the switch register up for the first ADC reading
-+ */
-+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ1);
-+
-+ /*
-+ * Initialize our software state machine to know which ADC
-+ * reading to take
-+ */
-+ sTouch.state = TS_STATE_Z1;
-+
-+ /*
-+ * Set the timer so after a mSec or two settling delay it will
-+ * take the first ADC reading.
-+ */
-+ Set_Timer2_uSec(EP93XX_TS_PER_POINT_DELAY_USEC);
-+
-+ /*
-+ * Note that we are in sw scanning mode not hw scanning mode.
-+ */
-+ gScanningMode = TS_MODE_SOFT_SCAN;
-+
-+}
-+
-+static void Set_Timer2_uSec(unsigned int uiDelay_uSec)
-+{
-+ unsigned int uiClockTicks;
-+
-+ /*
-+ * Stop timer 2
-+ */
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+
-+ uiClockTicks = ((uiDelay_uSec * 508) + 999) / 1000;
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_LOAD);
-+ __raw_writel(uiClockTicks, EP93XX_TIMER2_VALUE);
-+
-+ /*
-+ * Set up Timer 2 for 508 kHz clock and periodic mode.
-+ */
-+ __raw_writel(0xC8, EP93XX_TIMER2_CONTROL);
-+
-+}
-+
-+static void Stop_Timer2(void)
-+{
-+ __raw_writel(0, EP93XX_TIMER2_CONTROL);
-+}
-+
-+/*
-+ * Initialization and exit routines
-+ */
-+int __init ep93xx_ts_init(void)
-+{
-+ int retval;
-+
-+ retval = request_irq(IRQ_EP93XX_TOUCH, ep93xx_ts_isr,
-+ IRQF_DISABLED, "ep93xx_ts", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get touchscreen IRQ\n");
-+ return retval;
-+ }
-+
-+ retval = request_irq(IRQ_EP93XX_TIMER2, ep93xx_timer2_isr,
-+ IRQF_DISABLED, "ep93xx_timer2", 0);
-+ if (retval)
-+ {
-+ printk(KERN_WARNING "ep93xx_ts: failed to get timer2 IRQ\n");
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ return retval;
-+ }
-+
-+ misc_register(&ep93xx_ts_miscdev);
-+
-+ sTouch.state = TS_STATE_STOPPED;
-+ gScanningMode = TS_MODE_UN_INITIALIZED;
-+
-+ printk(KERN_NOTICE "ep93xx touchscreen driver configured for 4-wire operation\n");
-+
-+ return 0;
-+}
-+
-+void __exit ep93xx_ts_exit(void)
-+{
-+ Stop_Timer2();
-+
-+ free_irq(IRQ_EP93XX_TOUCH, 0);
-+ free_irq(IRQ_EP93XX_TIMER2, 0);
-+
-+ misc_deregister(&ep93xx_ts_miscdev);
-+}
-+
-+module_init(ep93xx_ts_init);
-+module_exit(ep93xx_ts_exit);
-+
-+MODULE_DESCRIPTION("Cirrus EP93xx touchscreen driver");
-+MODULE_SUPPORTED_DEVICE("touchscreen/ep93xx");
-+MODULE_LICENSE("GPL");
---- a/arch/arm/mach-ep93xx/core.c
-+++ b/arch/arm/mach-ep93xx/core.c
-@@ -205,6 +205,7 @@ void ep93xx_syscon_swlocked_write(unsign
-
- spin_unlock_irqrestore(&syscon_swlock, flags);
- }
-+EXPORT_SYMBOL(ep93xx_syscon_swlocked_write);
-
- void ep93xx_devcfg_set_clear(unsigned int set_bits, unsigned int clear_bits)
- {
+++ /dev/null
-This enables the mmc-over-spi driver for the Sim.One board, based on Mika's
-patch, which used a GPIO for chip select in stead of the default SFRMOUT pin.
-I've modified it to use the usual SFRMOUT; if you've modified your Sim.One
-board to use a GPIO instead, uncomment and modify
-// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-in the source file.
- -martinwguy, 14 May 2010
-
-From: Mika Westerberg <mika.westerberg@iki.fi>
-Date: Wed, 28 Apr 2010 08:42:46 +0300
-Subject: [PATCH] ep93xx: simone: added board specific SPI support for MMC/SD cards
-
-This includes setting up EGPIOs 0 and 9 for card detection and chip select
-respectively.
-
---- a/arch/arm/mach-ep93xx/simone.c
-+++ b/arch/arm/mach-ep93xx/simone.c
-@@ -20,10 +20,15 @@
- #include <linux/platform_device.h>
- #include <linux/i2c.h>
- #include <linux/i2c-gpio.h>
-+#include <linux/gpio.h>
-+#include <linux/mmc/host.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/mmc_spi.h>
-
- #include <mach/hardware.h>
- #include <linux/platform_data/video-ep93xx.h>
- #include <mach/gpio-ep93xx.h>
-+#include <linux/platform_data/spi-ep93xx.h>
-
- #include <asm/hardware/vic.h>
- #include <asm/mach-types.h>
-@@ -41,6 +46,135 @@ static struct ep93xxfb_mach_info __initd
- .flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
- };
-
-+/*
-+ * GPIO lines used for MMC card detection.
-+ */
-+#define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0
-+
-+/*
-+ * If you have hacked your Sim.One to use a GPIO as SD card chip select
-+ * (SD pin 1), uncomment the following line.
-+ * The example, EGPIO15, is on TP17 near the CPU.
-+ */
-+// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15
-+
-+/*
-+ * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal,
-+ * you can leave these empty and pass NULL as .controller_data.
-+ */
-+
-+#ifdef MMC_CHIP_SELECT_GPIO
-+static int simone_mmc_spi_setup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+ int err;
-+
-+ err = gpio_request(gpio, spi->modalias);
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_output(gpio, 1);
-+ if (err) {
-+ gpio_free(gpio);
-+ return err;
-+ }
-+
-+ return 0;
-+}
-+
-+static void simone_mmc_spi_cleanup(struct spi_device *spi)
-+{
-+ unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-+
-+ gpio_set_value(gpio, 1);
-+ gpio_direction_input(gpio);
-+ gpio_free(gpio);
-+}
-+
-+static void simone_mmc_spi_cs_control(struct spi_device *spi, int value)
-+{
-+ gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-+}
-+
-+static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = {
-+ .setup = simone_mmc_spi_setup,
-+ .cleanup = simone_mmc_spi_cleanup,
-+ .cs_control = simone_mmc_spi_cs_control,
-+};
-+#endif
-+
-+/*
-+ * MMC card detection GPIO setup.
-+ */
-+static int simone_mmc_spi_init(struct device *dev,
-+ irqreturn_t (*irq_handler)(int, void *), void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+ int irq, err;
-+
-+ err = gpio_request(gpio, dev_name(dev));
-+ if (err)
-+ return err;
-+
-+ err = gpio_direction_input(gpio);
-+ if (err)
-+ goto fail;
-+
-+ irq = gpio_to_irq(gpio);
-+ if (irq < 0)
-+ goto fail;
-+
-+ err = request_irq(irq, irq_handler, IRQF_TRIGGER_FALLING,
-+ "MMC card detect", mmc);
-+ if (err)
-+ goto fail;
-+
-+ printk(KERN_INFO "%s: using irq %d for MMC card detection\n",
-+ dev_name(dev), irq);
-+
-+ return 0;
-+fail:
-+ gpio_free(gpio);
-+ return err;
-+}
-+
-+static void simone_mmc_spi_exit(struct device *dev, void *mmc)
-+{
-+ unsigned int gpio = MMC_CARD_DETECT_GPIO;
-+
-+ free_irq(gpio_to_irq(gpio), mmc);
-+ gpio_free(gpio);
-+}
-+
-+static struct mmc_spi_platform_data simone_mmc_spi_data = {
-+ .init = simone_mmc_spi_init,
-+ .exit = simone_mmc_spi_exit,
-+ .detect_delay = 500,
-+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
-+};
-+
-+static struct spi_board_info simone_spi_devices[] __initdata = {
-+ {
-+ .modalias = "mmc_spi",
-+#ifdef MMC_CHIP_SELECT_GPIO
-+ .controller_data = &simone_mmc_spi_ops,
-+#endif
-+ .platform_data = &simone_mmc_spi_data,
-+ /*
-+ * We use 10 MHz even though the maximum is 3.7 MHz. The driver
-+ * will limit it automatically to max. frequency.
-+ */
-+ .max_speed_hz = 10 * 1000 * 1000,
-+ .bus_num = 0,
-+ .chip_select = 0,
-+ .mode = SPI_MODE_3,
-+ },
-+};
-+
-+static struct ep93xx_spi_info simone_spi_info __initdata = {
-+ .num_chipselect = ARRAY_SIZE(simone_spi_devices),
-+};
-+
- static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = {
- .sda_pin = EP93XX_GPIO_LINE_EEDAT,
- .sda_is_open_drain = 0,
-@@ -75,6 +209,8 @@ static void __init simone_init_machine(v
- ep93xx_register_fb(&simone_fb_info);
- ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
- ARRAY_SIZE(simone_i2c_board_info));
-+ ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
-+ ARRAY_SIZE(simone_spi_devices));
- simone_register_audio();
- }
-
+++ /dev/null
-#
-# Copyright (C) 2012 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-define Profile/Default
- NAME:=Default Profile
- PACKAGES:= \
- kmod-usb-core kmod-usb-ohci
-endef
-
-define Profile/Default/Description
- Default package set compatible with most EP93xx-based boards.
-endef
-$(eval $(call Profile,Default))
+++ /dev/null
-#
-# Copyright (C) 2012 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-define Profile/Simone
- NAME:=Simplemachines Sim.One
- PACKAGES:= \
- kmod-input-core \
- kmod-input-evdev \
- kmod-input-keyboard-ep93xx \
- kmod-sound-core \
- kmod-sound-soc-ep93xx \
- kmod-sound-soc-ep93xx-ac97 \
- kmod-sound-soc-ep93xx-simone
-endef
-
-define Profile/Simone/Description
- Package set compatible with the Simplemachines Sim.One board.
-endef
-$(eval $(call Profile,Simone))
projects / openwrt / staging / wigyori.git / commitdiff