ath79: split Teltonika RUT955 to support other RUT9xx models

Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

diff --git a/target/linux/ath79/dts/ar9344_teltonika_rut955.dts b/target/linux/ath79/dts/ar9344_teltonika_rut955.dts
index a8aeef0fa456f3cec4cb68487eb6363b9a05339b..53dc7dd9b9bd5e160b10108096a97a694bc7fd2d 100644 (file)
--- a/target/linux/ath79/dts/ar9344_teltonika_rut955.dts
+++ b/target/linux/ath79/dts/ar9344_teltonika_rut955.dts
@@ -1,63 +1,44 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /dts-v1/;
 
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /dts-v1/;
 

-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-#include "ar9344.dtsi"
+#include "ar9344_teltonika_rut9xx.dtsi"

 
 / {
        model = "Teltonika RUT955";
 
 / {
        model = "Teltonika RUT955";

-       compatible = "teltonika,rut955", "qca,ar9344";
+       compatible = "teltonika,rut955", "teltonika,rut9xx", "qca,ar9344";

 
        aliases {
 
        aliases {

-               serial0 = &uart;
-               serial1 = &hs_uart;

                led-boot = &led_system_green;
                led-failsafe = &led_system_red;
                led-running = &led_system_green;
                led-upgrade = &led_system_red;
                led-boot = &led_system_green;
                led-failsafe = &led_system_red;
                led-running = &led_system_green;
                led-upgrade = &led_system_red;

-               label-mac-device = &eth1;
-       };
-
-       i2c {
-               compatible = "i2c-gpio";
-               scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-               sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-               #address-cells = <1>;
-               #size-cells = <0>;
-
-               hwmon@4d {
-                       compatible = "microchip,mcp3221";
-                       reg = <0x4d>;
-               };

        };
 
        leds {
                compatible = "gpio-leds";
 
        };
 
        leds {
                compatible = "gpio-leds";
 

+               signal0 {
+                       label = "rut955:green:signal0";
+                       gpios = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+               };
+

                signal1 {
                        label = "rut955:green:signal1";
                signal1 {
                        label = "rut955:green:signal1";

-                       gpios = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+                       gpios = <&gpio_ext 1 GPIO_ACTIVE_HIGH>;

                };
 
                signal2 {
                        label = "rut955:green:signal2";
                };
 
                signal2 {
                        label = "rut955:green:signal2";

-                       gpios = <&gpio_ext 1 GPIO_ACTIVE_HIGH>;
+                       gpios = <&gpio_ext 2 GPIO_ACTIVE_HIGH>;

                };
 
                signal3 {
                        label = "rut955:green:signal3";
                };
 
                signal3 {
                        label = "rut955:green:signal3";

-                       gpios = <&gpio_ext 2 GPIO_ACTIVE_HIGH>;
+                       gpios = <&gpio_ext 3 GPIO_ACTIVE_HIGH>;

                };
 
                signal4 {
                        label = "rut955:green:signal4";
                };
 
                signal4 {
                        label = "rut955:green:signal4";

-                       gpios = <&gpio_ext 3 GPIO_ACTIVE_HIGH>;
-               };
-
-               signal5 {
-                       label = "rut955:green:signal5";

                        gpios = <&gpio_ext 4 GPIO_ACTIVE_HIGH>;
                };
 
                        gpios = <&gpio_ext 4 GPIO_ACTIVE_HIGH>;
                };
 


@@ -72,17 +53,6 @@
                        default-state = "on";
                };
        };
                        default-state = "on";
                };
        };

-
-       keys {
-               compatible = "gpio-keys";
-
-               reset {
-                       label = "reset";
-                       linux,code = <KEY_RESTART>;
-                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
-                       debounce-interval = <60>;
-               };
-       };

 };
 
 &gpio {
 };
 
 &gpio {


@@ -169,83 +139,12 @@
        };
 };
 
        };
 };
 

-&ref {
-       clock-frequency = <40000000>;
-};
-
-&uart {
-       status = "okay";
-};
-
-&hs_uart {
-       status = "okay";
-
-       pinctrl-names = "default";
-       pinctrl-0 = <&pmx_uart2>;
-
-       rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
-       rs485-rts-active-low;
-       linux,rs485-enabled-at-boot-time;
-};
-

 &spi {
        status = "okay";
 
        num-cs = <3>;
        pinctrl-names = "default";
 &spi {
        status = "okay";
 
        num-cs = <3>;
        pinctrl-names = "default";

-       pinctrl-0 = <&pmx_spi>;
-
-       flash@0 {
-               compatible = "jedec,spi-nor";
-               reg = <0>;
-               spi-max-frequency = <25000000>;
-
-               partitions {
-                       compatible = "fixed-partitions";
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-
-                       partition@0 {
-                               label = "u-boot";
-                               reg = <0x0 0x20000>;
-                               read-only;
-                       };
-
-                       config: partition@20000 {
-                               label = "config";
-                               reg = <0x20000 0x10000>;
-                               read-only;
-                       };
-
-                       art: partition@30000 {
-                               label = "art";
-                               reg = <0x30000 0x10000>;
-                               read-only;
-                       };
-
-                       partition@40000 {
-                               label = "firmware";
-                               reg = <0x40000 0xf30000>;
-                               compatible = "tplink,firmware";
-                       };
-
-                       partition@f70000 {
-                               label = "event-log";
-                               reg = <0xf70000 0x90000>;
-                               read-only;
-                       };
-               };
-       };
-
-       microsd@1 {
-               status = "disabled";
-
-               compatible = "mmc-spi-slot";
-               spi-max-frequency = <25000000>;
-               reg = <1>;
-               voltage-ranges = <3200 3400>;
-               broken-cd;
-       };
+       pinctrl-0 = <&pmx_spi>, <&pmx_spi_ext>;

 
        gpio_ext: gpio_ext@2 {
                compatible = "fairchild,74hc595";
 
        gpio_ext: gpio_ext@2 {
                compatible = "fairchild,74hc595";


@@ -254,51 +153,16 @@
                #gpio-cells = <2>;
                registers-number = <2>;
                spi-max-frequency = <10000000>;
                #gpio-cells = <2>;
                registers-number = <2>;
                spi-max-frequency = <10000000>;

-               gpio-line-names = "led_signal_bar1", "led_signal_bar2", "led_signal_bar3", "led_signal_bar4",
-                       "led_signal_bar5", "led_status_red", "led_status_green", "sim_sel",
+               gpio-line-names = "signal_bar0", "signal_bar1", "signal_bar2", "signal_bar3",
+                       "signal_bar4", "status_red", "status_green", "sim_sel",

                        "DOUT1", "DOUT2", "modem_vbus", "modem_rst",
                        "DOUT3", "RS485_R", "SDCS", "HWRST";
        };
 };
 
                        "DOUT1", "DOUT2", "modem_vbus", "modem_rst",
                        "DOUT3", "RS485_R", "SDCS", "HWRST";
        };
 };
 

-&usb {
-       #address-cells = <1>;
-       #size-cells = <0>;
-       status = "okay";
-
-       port@1 {
-               #address-cells = <1>;
-               #size-cells = <0>;
-               reg = <1>;
-
-               port@1 {
-                       compatible = "usb-a-connector";
-                       reg = <1>;
-               };
-
-               port@3 {
-                       label = "RS-232 serial adapter";
-                       reg = <3>;
-               };
-
-               port@4 {
-                       label = "internal wwan modem";
-                       reg = <4>;
-               };
-       };
-};
-
-&usb_phy {
-       status = "okay";
-};
-
-&wmac {
-       status = "okay";
-
-       mtd-cal-data = <&art 0x1000>;
-       mtd-mac-address = <&config 0x0>;
-       mtd-mac-address-increment = <2>;
-};
+&hs_uart {
+       dtr-gpios = <&gpio_ext 13 GPIO_ACTIVE_HIGH>;
+}

 
 &eth0 {
        status = "okay";
 
 &eth0 {
        status = "okay";


@@ -321,26 +185,10 @@
 };
 
 &pinmux {
 };
 
 &pinmux {

-       pmx_spi: spi {
-               // SPI_CS1 on GPIO 3, 2nd SCK on GPIO 4
-               // 2nd MOSI on GPIO 12, SPI_CS2 on GPIO 20
-               pinctrl-single,bits = <0x0 0x07000000 0xff000000>,
-                                       <0x4 0x0a 0xff>,
+       pmx_spi_ext: spi_ext {
+               // 2nd SCK on GPIO 4, 2nd MOSI on GPIO 12, SPI_CS2 on GPIO 20
+               pinctrl-single,bits = <0x4 0x0a 0xff>,

                                        <0xc 0x0b 0xff>,
                                        <0x14 0x08 0xff>;
        };
                                        <0xc 0x0b 0xff>,
                                        <0x14 0x08 0xff>;
        };

-
-       pmx_leds_switch: leds_switch {
-               // switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
-               pinctrl-single,bits =  <0x0 0x00002d00 0x0000ff00>,
-                                       <0xc 0x002c2b00 0x00ffff00>,
-                                       <0x14 0x002a0000 0x00ff0000>;
-       };
-
-       pmx_uart2: uart2 {
-               // UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
-               pinctrl-single,bits = <0x0 0x0 0xff>,
-                               <0x10 0x4f000000 0xff000000>,
-                               <0x3c 0x000b0000 0x00ff0000>;
-       };

 };
 };

diff --git a/target/linux/ath79/dts/ar9344_teltonika_rut9xx.dtsi b/target/linux/ath79/dts/ar9344_teltonika_rut9xx.dtsi
new file mode 100644 (file)
index 0000000..0025e5d
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_teltonika_rut9xx.dtsi
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+       compatible = "teltonika,rut9xx", "qca,ar9344";
+
+       aliases {
+               serial0 = &uart;
+               serial1 = &hs_uart;
+               label-mac-device = &eth1;
+       };
+
+       i2c0: i2c {
+               compatible = "i2c-gpio";
+               scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+               sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               hwmon@4d {
+                       compatible = "microchip,mcp3221";
+                       reg = <0x4d>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&ref {
+       clock-frequency = <40000000>;
+};
+
+&uart {
+       status = "okay";
+};
+
+&hs_uart {
+       status = "okay";
+
+       pinctrl-names = "default";
+       pinctrl-0 = <&pmx_uart2>;
+
+       rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+       rs485-rts-active-low;
+       linux,rs485-enabled-at-boot-time;
+};
+
+&spi {
+       status = "okay";
+       num-cs = <2>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pmx_spi>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x20000>;
+                               read-only;
+                       };
+
+                       config: partition@20000 {
+                               label = "config";
+                               reg = <0x20000 0x10000>;
+                               read-only;
+                       };
+
+                       art: partition@30000 {
+                               label = "art";
+                               reg = <0x30000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "firmware";
+                               reg = <0x40000 0xf30000>;
+                               compatible = "tplink,firmware";
+                       };
+
+                       partition@f70000 {
+                               label = "event-log";
+                               reg = <0xf70000 0x90000>;
+                               read-only;
+                       };
+               };
+       };
+
+       microsd@1 {
+               status = "disabled";
+
+               compatible = "mmc-spi-slot";
+               spi-max-frequency = <25000000>;
+               reg = <1>;
+               voltage-ranges = <3200 3400>;
+               broken-cd;
+       };
+};
+
+&usb {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       port@1 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <1>;
+
+               port@1 {
+                       compatible = "usb-a-connector";
+                       reg = <1>;
+               };
+
+               port@3 {
+                       label = "RS-232 serial adapter";
+                       reg = <3>;
+               };
+
+               port@4 {
+                       label = "internal wwan modem";
+                       reg = <4>;
+               };
+       };
+};
+
+&usb_phy {
+       status = "okay";
+};
+
+&wmac {
+       status = "okay";
+
+       mtd-cal-data = <&art 0x1000>;
+       mtd-mac-address = <&config 0x0>;
+       mtd-mac-address-increment = <2>;
+};
+
+&pinmux {
+       pmx_spi: spi {
+               // SPI_CS1 on GPIO 3
+               pinctrl-single,bits = <0x0 0x07000000 0xff000000>;
+       };
+
+       pmx_leds_switch: leds_switch {
+               // switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
+               pinctrl-single,bits =  <0x0 0x00002d00 0x0000ff00>,
+                                       <0xc 0x002c2b00 0x00ffff00>,
+                                       <0x14 0x002a0000 0x00ff0000>;
+       };
+
+       pmx_uart2: uart2 {
+               // UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
+               pinctrl-single,bits = <0x0 0x0 0xff>,
+                               <0x10 0x4f000000 0xff000000>,
+                               <0x3c 0x000b0000 0x00ff0000>;
+       };
+};