lantiq: add support for Arcadyan ARV7519PW
authorJohn Crispin <john@openwrt.org>
Sun, 30 Mar 2014 09:16:15 +0000 (09:16 +0000)
committerJohn Crispin <john@openwrt.org>
Sun, 30 Mar 2014 09:16:15 +0000 (09:16 +0000)
This patch adds almost full support for this board.

- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port

Signed-off-by: Antonios Vamporakis <ant@area128.com>
SVN-Revision: 40319

target/linux/lantiq/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
target/linux/lantiq/base-files/etc/uci-defaults/02_network
target/linux/lantiq/dts/ARV7519PW.dts [new file with mode: 0644]
target/linux/lantiq/image/Makefile
target/linux/lantiq/xway/profiles/arv.mk

index 2d5e09d01519491285ecabf8431e093e8f9d4fa4..a849584fcf17f0a561393f8dd3270d4e2ca03b2d 100644 (file)
@@ -29,7 +29,7 @@ case "$FIRMWARE" in
 "RT2860.eeprom" )
        local board=$(lantiq_board_id)
        case $board in
-       ARV7510PW22|ARV7525PW|ARV752DPW|ARV752DPW22)
+       ARV7510PW22|ARV7519PW|ARV7525PW|ARV752DPW|ARV752DPW22)
                rt2x00_eeprom_extract "board_config" 1040 512
                ;;
        *)
index 4903eb92d0031ef8eda00fa2d77e3c2717bc6567..329fa2d72e5180be1ffea3ef544bd608e5e86c2a 100644 (file)
@@ -74,6 +74,15 @@ ARV4519PW|ARV7510PW22|ARV7518PW|ARV752DPW22)
        ucidef_add_switch_vlan "switch0" "1" "0t 2 3 4 5"
        ;;
 
+# rtl8306g
+ARV7519PW)
+       lan_mac=$(mtd_get_mac_binary board_config 22)
+       wan_mac=$(macaddr_add "$lan_mac" 1)
+       ucidef_set_interface_lan "eth0.1"
+       ucidef_add_switch "switch0" "1" "1"
+       ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 4t"
+       ;;
+
 WBMR)
        ucidef_set_interface_lan "eth0.1"
        ucidef_add_switch "switch0" "1" "1"
diff --git a/target/linux/lantiq/dts/ARV7519PW.dts b/target/linux/lantiq/dts/ARV7519PW.dts
new file mode 100644 (file)
index 0000000..1478192
--- /dev/null
@@ -0,0 +1,213 @@
+/dts-v1/;
+
+/include/ "danube.dtsi"
+
+/ {
+       model = "ARV7519PW - Astoria Networks";
+
+       chosen {
+               bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+       };
+
+       memory@0 {
+               reg = <0x0 0x4000000>;
+       };
+
+       sram@1F000000 {
+               vmmc@107000 {
+                       status = "okay";
+               };
+       };
+
+       fpi@10000000 {
+               localbus@0 {
+                       nor-boot@0 {
+                               compatible = "lantiq,nor";
+                               bank-width = <2>;
+                               reg = <0 0x0 0x2000000>;
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+
+                               partition@0 {
+                                       label = "uboot";
+                                       reg = <0x00000 0x40000>;
+                                       read-only;
+                               };
+
+                               partition@40000 {
+                                       label = "uboot_env";
+                                       reg = <0x40000 0x20000>;
+                               };
+
+                               partition@60000 {
+                                       label = "firmware";
+                                       reg = <0x60000 0xf80000>;
+                               };
+
+                               partition@fe0000 {
+                                       label = "board_config";
+                                       reg = <0xfe0000 0x20000>;
+                                       read-only;
+                               };
+                       };
+
+                       mac_addr {
+                               compatible = "lantiq,eth-mac";
+                               reg = <0 0xfe0016 0x6>;
+                               mac-increment = <2>;
+                       };
+               };
+
+               gpio: pinmux@E100B10 {
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&state_default>;
+
+                       state_default: pinmux {
+                               ebu {
+                                       lantiq,groups = "ebu cs1";
+                                       lantiq,function = "ebu";
+                               };
+                               pci_in {
+                                       lantiq,groups = "req1";
+                                       lantiq,function = "pci";
+                                       lantiq,open-drain = <1>;
+                                       lantiq,pull = <2>;
+                                       lantiq,output = <0>;
+                               };
+                               pci_out {
+                                       lantiq,groups = "gnt1";
+                                       lantiq,function = "pci";
+                                       lantiq,pull = <0>;
+                                       lantiq,output = <1>;
+                               };
+                               pci_rst {
+                                       lantiq,pins = "io21";
+                                       lantiq,pull = <2>;
+                                       lantiq,output = <1>;
+                               };
+                               switch_rst {
+                                       lantiq,pins = "io19";
+                                       lantiq,pull = <2>;
+                                       lantiq,output = <1>;
+                               };
+                       };
+               };
+
+               etop@E180000 {
+                       phy-mode = "mii";
+               };
+
+               /* warning: passive port
+               only works with active devices */
+               ifxhcd@E101000 {
+                       status = "okay";
+               };
+
+               pci@E105400 {
+                       status = "okay";
+                       lantiq,external-clock;
+                       gpio-reset = <&gpio 21 0>;
+                       req-mask = <0xf>;
+               };    
+       };
+
+       ralink_eep {
+               compatible = "ralink,eeprom";
+               ralink,eeprom = "RT2860.eeprom";
+        };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <100>;
+
+               rfkill {
+                       label = "rfkill";
+                       gpios = <&gpio 11 1>;
+                       linux,code = <0xf7>;
+               };
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 28 1>;
+                       linux,code = <0x198>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+               power {
+                       label = "power";
+                       gpios = <&gpio 2 1>;
+                       default-state = "off";
+               };
+               power2 {
+                       label = "power2";
+                       gpios = <&gpio 14 1>;
+               };
+               online {
+                       label = "online";
+                       gpios = <&gpio 3 1>;
+               };
+               online2 {
+                       label = "online2";
+                       gpios = <&gpio 30 1>;
+               };
+               wifi {
+                       label = "wifi";
+                       gpios = <&gpio 12 1>;
+               };
+               wifi2 {
+                       label = "wifi2";
+                       gpios = <&gpio 10 1>;
+               };
+               wifi3 {
+                       label = "wifi3";
+                       gpios = <&gpio 6 1>;
+               };
+               voice {
+                       label = "voice";
+                       gpios = <&gpio 31 1>;
+               };
+               wps {
+                       label = "wps";
+                       gpios = <&gpio 15 1>;
+               };
+               wps2 {
+                       label = "wps2";
+                       gpios = <&gpio 7 1>;
+               };
+               wps3 {
+                       label = "wps3";
+                       gpios = <&gpio 23 1>;
+               };
+               dsl {
+                       label = "dsl";
+                       gpios = <&gpio 4 1>;
+               };
+               lan {
+                       label = "lan";
+                       gpios = <&gpio 1 1>;
+               };
+               tv {
+                       label = "tv";
+                       gpios = <&gpio 20 1>;
+               };
+               upgrade {
+                       label = "upgrade";
+                       gpios = <&gpio 29 1>;
+               };
+       };
+
+       /* is there another way to "reserve" the GPIO? */
+       gpio_export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               switch {
+                       gpio-export,name = "switch";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio 19 0>;
+               };
+       };
+};
index 4550fc4619204c35febe814eb336d9ec757a81fe..cd36d12ca1c826c595dc1323286221e1fcb553ba 100644 (file)
@@ -269,6 +269,9 @@ Image/Build/Profile/ARV7510PW22=$(call Image/Build/$(1),$(1),ARV7510PW22)
 Image/BuildKernel/Profile/ARV7518PW=$(call Image/BuildKernel/Template,ARV7518PW)
 Image/Build/Profile/ARV7518PW=$(call Image/Build/$(1),$(1),ARV7518PW)
 
+Image/BuildKernel/Profile/ARV7519PW=$(call Image/BuildKernel/Template,ARV7519PW)
+Image/Build/Profile/ARV7519PW=$(call Image/Build/$(1),$(1),ARV7519PW)
+
 Image/BuildKernel/Profile/ARV752DPW=$(call Image/BuildKernel/Template,ARV752DPW)
 Image/Build/Profile/ARV752DPW=$(call Image/Build/$(1),$(1),ARV752DPW)
 
index 9b172f266ef270f7d24840da4094f7d6fce684cf..30cc7780bbecfb94219f69e5733b33e79708a5a1 100644 (file)
@@ -92,6 +92,18 @@ endef
 
 $(eval $(call Profile,ARV7518PW))
 
+define Profile/ARV7519PW
+  NAME:=Astoria - ARV7519PW
+  PACKAGES:=kmod-ltq-hcd-danube kmod-ledtrig-usbdev \
+       kmod-ltq-adsl-danube-mei kmod-ltq-adsl-danube \
+       kmod-ltq-adsl-danube-fw-a kmod-ltq-atm-danube \
+       ltq-adsl-app ppp-mod-pppoa \
+       kmod-rt2800-pci wpad-mini \
+       swconfig
+endef
+
+$(eval $(call Profile,ARV7519PW))
+
 define Profile/ARV4520PW
   NAME:=Easybox 800, WAV-281 - ARV4520PW
   PACKAGES:=kmod-ltq-hcd-danube kmod-ledtrig-usbdev \