target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca955x.dtsi"
   8
   9 / {
  10         compatible = "mikrotik,routerboard-922uags-5hpacd", "qca,qca9558";
  11         model = "MikroTik RouterBOARD 922UAGS-5HPacD";
  12
  13         aliases {
  14                 led-boot = &led_user;
  15                 led-failsafe = &led_user;
  16                 led-upgrade = &led_user;
  17                 serial0 = &uart;
  18         };
  19
  20         chosen {
  21                 bootargs = "console=ttyS0,115200n8";
  22         };
  23
  24         leds {
  25                 compatible = "gpio-leds";
  26
  27                 led_user: user {
  28                         label = "mikrotik:green:user";
  29                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  30                 };
  31         };
  32
  33         ath10k-leds {
  34                 compatible = "gpio-leds";
  35
  36                 wlan5g {
  37                         label = "mikrotik:green:wlan5g";
  38                         gpios = <&ath10k 0 GPIO_ACTIVE_LOW>;
  39                         linux,default-trigger = "phy0tpt";
  40                 };
  41         };
  42
  43         keys {
  44                 compatible = "gpio-keys";
  45
  46                 reset {
  47                         label = "reset";
  48                         linux,code = <KEY_RESTART>;
  49                         gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
  50                         debounce-interval = <60>;
  51                 };
  52         };
  53
  54         gpio-export {
  55                 compatible = "gpio-export";
  56
  57                 gpio_usb_power {
  58                         gpio-export,name = "mikrotik:power:usb";
  59                         gpio-export,output = <0>;
  60                         gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
  61                 };
  62
  63                 gpio_nand_power {
  64                         gpio-export,name = "mikrotik:power:nand";
  65                         gpio-export,output = <0>;
  66                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  67                 };
  68         };
  69 };
  70
  71 &mdio0 {
  72         status = "okay";
  73
  74         phy4: ethernet-phy@4 {
  75                 reg = <4>;
  76         };
  77 };
  78
  79 &eth0 {
  80         status = "okay";
  81
  82         phy-handle = <&phy4>;
  83         pll-data = <0x8f000000 0xa0000101 0xa0001313>;
  84
  85         gmac-config {
  86                 device = <&gmac>;
  87                 rgmii-enabled = <1>;
  88         };
  89 };
  90
  91 &spi {
  92         status = "okay";
  93
  94         flash@0 {
  95                 compatible = "jedec,spi-nor";
  96                 reg = <0>;
  97                 spi-max-frequency = <25000000>;
  98
  99                 partitions {
 100                         compatible = "mikrotik,routerboot-partitions";
 101                         #address-cells = <1>;
 102                         #size-cells = <1>;
 103
 104                         partition@0 {
 105                                 label = "routerboot";
 106                                 reg = <0x0 0x0>;
 107                                 read-only;
 108                         };
 109
 110                         hard_config: hard_config {
 111                                 read-only;
 112                         };
 113
 114                         bios {
 115                                 read-only;
 116                         };
 117
 118                         soft_config {
 119                         };
 120                 };
 121         };
 122 };
 123
 124 &nand {
 125         status = "okay";
 126
 127         nand-ecc-mode = "soft";
 128         qca,nand-swap-dma;
 129         qca,nand-scan-fixup;
 130
 131         partitions {
 132                 compatible = "fixed-partitions";
 133                 #size-cells = <1>;
 134
 135                 partition@0 {
 136                         label = "booter";
 137                         reg = <0x0000000 0x0040000>;
 138                         read-only;
 139                 };
 140
 141                 partition@40000 {
 142                         label = "kernel";
 143                         reg = <0x0040000 0x03c0000>;
 144                 };
 145
 146                 partition@400000 {
 147                         label = "ubi";
 148                         reg = <0x0400000 0x7c00000>;
 149                 };
 150         };
 151 };
 152
 153 &uart {
 154         status = "okay";
 155 };
 156
 157 &pcie0 {
 158         status = "okay";
 159
 160         ath10k: wifi@0,0 {
 161                 compatible = "qcom,ath10k";
 162                 reg = <0 0 0 0 0>;
 163                 #gpio-cells = <2>;
 164                 gpio-controller;
 165         };
 166 };
 167
 168 &pcie1 {
 169         status = "okay";
 170 };
 171
 172 &usb0 {
 173         status = "okay";
 174 };
 175
 176 &usb_phy0 {
 177         status = "okay";
 178 };