Add preliminary support for USR8200 board
authorPeter Denison <openwrt@marshadder.org>
Sun, 26 Oct 2008 10:34:40 +0000 (10:34 +0000)
committerPeter Denison <openwrt@marshadder.org>
Sun, 26 Oct 2008 10:34:40 +0000 (10:34 +0000)
SVN-Revision: 13049

target/linux/ixp4xx/patches-2.6.26/500-usr8200_support.patch [new file with mode: 0644]

diff --git a/target/linux/ixp4xx/patches-2.6.26/500-usr8200_support.patch b/target/linux/ixp4xx/patches-2.6.26/500-usr8200_support.patch
new file mode 100644 (file)
index 0000000..7af0732
--- /dev/null
@@ -0,0 +1,327 @@
+Index: linux-2.6.26.5/arch/arm/mach-ixp4xx/Kconfig
+===================================================================
+--- linux-2.6.26.5.orig/arch/arm/mach-ixp4xx/Kconfig   2008-10-22 22:31:30.000000000 +0100
++++ linux-2.6.26.5/arch/arm/mach-ixp4xx/Kconfig        2008-10-22 22:40:55.000000000 +0100
+@@ -97,6 +97,14 @@ config MACH_SIDEWINDER
+         Engineering Sidewinder board. For more information on this
+         platform, see http://www.adiengineering.com
++config MACH_USR8200
++      bool "USRobotics USR8200"
++      select PCI
++      help
++        Say 'Y' here if you want your kernel to support the USRobotics
++        USR8200 router board. For more information on this platform, see
++        http://openwrt.org
++
+ config MACH_COMPEX
+       bool "Compex WP18 / NP18A"
+       select PCI
+Index: linux-2.6.26.5/arch/arm/mach-ixp4xx/Makefile
+===================================================================
+--- linux-2.6.26.5.orig/arch/arm/mach-ixp4xx/Makefile  2008-10-22 22:31:37.000000000 +0100
++++ linux-2.6.26.5/arch/arm/mach-ixp4xx/Makefile       2008-10-22 22:49:38.000000000 +0100
+@@ -24,6 +24,7 @@ obj-pci-$(CONFIG_MACH_COMPEX)                += ixdp42
+ obj-pci-$(CONFIG_MACH_WRT300NV2)              += wrt300nv2-pci.o
+ obj-pci-$(CONFIG_MACH_AP1000)         += ixdp425-pci.o
+ obj-pci-$(CONFIG_MACH_TW5334)         += tw5334-pci.o
++obj-pci-$(CONFIG_MACH_USR8200)                += usr8200-pci.o
+ obj-y += common.o
+@@ -46,6 +47,7 @@ obj-$(CONFIG_MACH_COMPEX)    += compex-setu
+ obj-$(CONFIG_MACH_WRT300NV2)  += wrt300nv2-setup.o
+ obj-$(CONFIG_MACH_AP1000)     += ap1000-setup.o
+ obj-$(CONFIG_MACH_TW5334)     += tw5334-setup.o
++obj-$(CONFIG_MACH_USR8200)    += usr8200-setup.o
+ obj-$(CONFIG_PCI)             += $(obj-pci-$(CONFIG_PCI)) common-pci.o
+ obj-$(CONFIG_IXP4XX_QMGR)     += ixp4xx_qmgr.o
+Index: linux-2.6.26.5/arch/arm/mach-ixp4xx/usr8200-pci.c
+===================================================================
+--- /dev/null  1970-01-01 00:00:00.000000000 +0000
++++ linux-2.6.26.5/arch/arm/mach-ixp4xx/usr8200-pci.c  2008-10-22 23:37:56.000000000 +0100
+@@ -0,0 +1,78 @@
++/*
++ * arch/arch/mach-ixp4xx/usr8200-pci.c
++ *
++ * PCI setup routines for USRobotics USR8200
++ *
++ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org>
++ *
++ * based on pronghorn-pci.c
++ *    Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ * based on coyote-pci.c:
++ *    Copyright (C) 2002 Jungo Software Technologies.
++ *    Copyright (C) 2003 MontaVista Softwrae, Inc.
++ *
++ * Maintainer: Peter Denison <openwrt@marshadder.org>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/pci.h>
++#include <linux/init.h>
++#include <linux/irq.h>
++
++#include <asm/mach-types.h>
++#include <asm/hardware.h>
++
++#include <asm/mach/pci.h>
++
++void __init usr8200_pci_preinit(void)
++{
++      set_irq_type(IRQ_IXP4XX_GPIO7, IRQT_LOW);
++      set_irq_type(IRQ_IXP4XX_GPIO8, IRQT_LOW);
++      set_irq_type(IRQ_IXP4XX_GPIO9, IRQT_LOW);
++      set_irq_type(IRQ_IXP4XX_GPIO10, IRQT_LOW);
++      set_irq_type(IRQ_IXP4XX_GPIO11, IRQT_LOW);
++
++      ixp4xx_pci_preinit();
++}
++
++static int __init usr8200_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
++{
++      if (slot == 14)
++              return IRQ_IXP4XX_GPIO7;
++      else if (slot == 15)
++              return IRQ_IXP4XX_GPIO8;
++      else if (slot == 16) {
++              if (pin == 1)
++                      return IRQ_IXP4XX_GPIO11;
++              else if (pin == 2)
++                      return IRQ_IXP4XX_GPIO10;
++              else if (pin == 3)
++                      return IRQ_IXP4XX_GPIO9;
++              else
++                      return -1;
++      } else
++              return -1;
++}
++
++struct hw_pci usr8200_pci __initdata = {
++      .nr_controllers = 1,
++      .preinit        = usr8200_pci_preinit,
++      .swizzle        = pci_std_swizzle,
++      .setup          = ixp4xx_setup,
++      .scan           = ixp4xx_scan_bus,
++      .map_irq        = usr8200_map_irq,
++};
++
++int __init usr8200_pci_init(void)
++{
++      if (machine_is_usr8200())
++              pci_common_init(&usr8200_pci);
++      return 0;
++}
++
++subsys_initcall(usr8200_pci_init);
+Index: linux-2.6.26.5/arch/arm/mach-ixp4xx/usr8200-setup.c
+===================================================================
+--- /dev/null  1970-01-01 00:00:00.000000000 +0000
++++ linux-2.6.26.5/arch/arm/mach-ixp4xx/usr8200-setup.c        2008-10-22 23:41:48.000000000 +0100
+@@ -0,0 +1,187 @@
++/*
++ * arch/arm/mach-ixp4xx/usr8200-setup.c
++ *
++ * Board setup for the USRobotics USR8200
++ *
++ * Copyright (C) 2008 Peter Denison <openwrt@marshadder.org>
++ *
++ * based on pronghorn-setup.c:
++ *    Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
++ * based on coyote-setup.c:
++ *      Copyright (C) 2003-2005 MontaVista Software, Inc.
++ *
++ * Author: Peter Denison <openwrt@marshadder.org>
++ */
++
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/device.h>
++#include <linux/serial.h>
++#include <linux/tty.h>
++#include <linux/serial_8250.h>
++#include <linux/slab.h>
++#include <linux/types.h>
++#include <linux/memory.h>
++#include <linux/i2c-gpio.h>
++#include <linux/leds.h>
++
++#include <asm/setup.h>
++#include <asm/hardware.h>
++#include <asm/irq.h>
++#include <asm/mach-types.h>
++#include <asm/mach/arch.h>
++#include <asm/mach/flash.h>
++
++static struct flash_platform_data usr8200_flash_data = {
++      .map_name       = "cfi_probe",
++      .width          = 2,
++};
++
++static struct resource usr8200_flash_resource = {
++      .flags          = IORESOURCE_MEM,
++};
++
++static struct platform_device usr8200_flash = {
++      .name           = "IXP4XX-Flash",
++      .id             = 0,
++      .dev            = {
++              .platform_data  = &usr8200_flash_data,
++      },
++      .num_resources  = 1,
++      .resource       = &usr8200_flash_resource,
++};
++
++static struct resource usr8200_uart_resources [] = {
++      {
++              .start          = IXP4XX_UART2_BASE_PHYS,
++              .end            = IXP4XX_UART2_BASE_PHYS + 0x0fff,
++              .flags          = IORESOURCE_MEM
++      },
++      {
++              .start          = IXP4XX_UART1_BASE_PHYS,
++              .end            = IXP4XX_UART1_BASE_PHYS + 0x0fff,
++              .flags          = IORESOURCE_MEM
++      }
++};
++
++static struct plat_serial8250_port usr8200_uart_data[] = {
++      {
++              .mapbase        = IXP4XX_UART2_BASE_PHYS,
++              .membase        = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
++              .irq            = IRQ_IXP4XX_UART2,
++              .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++              .iotype         = UPIO_MEM,
++              .regshift       = 2,
++              .uartclk        = IXP4XX_UART_XTAL,
++      },
++      {
++              .mapbase        = IXP4XX_UART1_BASE_PHYS,
++              .membase        = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
++              .irq            = IRQ_IXP4XX_UART1,
++              .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
++              .iotype         = UPIO_MEM,
++              .regshift       = 2,
++              .uartclk        = IXP4XX_UART_XTAL,
++      },
++      { },
++};
++
++static struct platform_device usr8200_uart = {
++      .name           = "serial8250",
++      .id             = PLAT8250_DEV_PLATFORM,
++      .dev            = {
++              .platform_data  = usr8200_uart_data,
++      },
++      .num_resources  = 2,
++      .resource       = usr8200_uart_resources,
++};
++
++/*
++static struct i2c_gpio_platform_data usr8200_i2c_gpio_data = {
++      .sda_pin        = 9,
++      .scl_pin        = 10,
++};
++
++static struct platform_device usr8200_i2c_gpio = {
++      .name           = "i2c-gpio",
++      .id             = 0,
++      .dev            = {
++              .platform_data  = &usr8200_i2c_gpio_data,
++      },
++};
++
++static struct gpio_led usr8200_led_pin[] = {
++      {
++              .name           = "usr8200:green:status",
++              .gpio           = 7,
++      }
++};
++
++static struct gpio_led_platform_data usr8200_led_data = {
++      .num_leds               = 1,
++      .leds                   = usr8200_led_pin,
++};
++
++static struct platform_device usr8200_led = {
++      .name                   = "leds-gpio",
++      .id                     = -1,
++      .dev.platform_data      = &usr8200_led_data,
++};
++*/
++
++static struct eth_plat_info usr8200_plat_eth[] = {
++      {
++              .phy            = 9,
++              .rxq            = 3,
++              .txreadyq       = 20,
++      }, {
++              .phy            = 16,
++              .rxq            = 4,
++              .txreadyq       = 21,
++      }
++};
++
++static struct platform_device usr8200_eth[] = {
++      {
++              .name                   = "ixp4xx_eth",
++              .id                     = IXP4XX_ETH_NPEB,
++              .dev.platform_data      = usr8200_plat_eth,
++      }, {
++              .name                   = "ixp4xx_eth",
++              .id                     = IXP4XX_ETH_NPEC,
++              .dev.platform_data      = usr8200_plat_eth + 1,
++      }
++};
++
++static struct platform_device *usr8200_devices[] __initdata = {
++      &usr8200_flash,
++      &usr8200_uart,
++/*    &usr8200_led,
++      &usr8200_i2c_gpio, */
++      &usr8200_eth[0],
++      &usr8200_eth[1],
++};
++
++static void __init usr8200_init(void)
++{
++      ixp4xx_sys_init();
++
++      usr8200_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
++      usr8200_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_64M - 1;
++
++      *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
++      *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
++
++      platform_add_devices(usr8200_devices, ARRAY_SIZE(usr8200_devices));
++}
++
++MACHINE_START(USR8200, "USRobotics USR8200")
++      /* Maintainer: Peter Denison <openwrt@marshadder.org> */
++      .phys_io        = IXP4XX_PERIPHERAL_BASE_PHYS,
++      .io_pg_offst    = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xfffc,
++      .map_io         = ixp4xx_map_io,
++      .init_irq       = ixp4xx_init_irq,
++      .timer          = &ixp4xx_timer,
++      .boot_params    = 0x0100,
++      .init_machine   = usr8200_init,
++MACHINE_END
+Index: linux-2.6.26.5/include/asm-arm/arch-ixp4xx/uncompress.h
+===================================================================
+--- linux-2.6.26.5.orig/include/asm-arm/arch-ixp4xx/uncompress.h       2008-10-22 23:27:33.000000000 +0100
++++ linux-2.6.26.5/include/asm-arm/arch-ixp4xx/uncompress.h    2008-10-22 23:28:09.000000000 +0100
+@@ -43,7 +43,7 @@ static __inline__ void __arch_decomp_set
+       if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
+                        machine_is_gateway7001() || machine_is_wg302v2() ||
+                        machine_is_pronghorn() || machine_is_pronghorn_metro() || machine_is_wrt300nv2() ||
+-                       machine_is_tw5334())
++                       machine_is_tw5334() || machine_is_usr8200())
+               uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
+       else
+               uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;