brcm63xx: Add Huawei HG655b support
authorJonas Gorski <jogo@openwrt.org>
Thu, 21 May 2015 19:31:54 +0000 (19:31 +0000)
committerJonas Gorski <jogo@openwrt.org>
Thu, 21 May 2015 19:31:54 +0000 (19:31 +0000)
This patch adds support for the Huawei HG655b.

Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45708

target/linux/brcm63xx/base-files/etc/diag.sh
target/linux/brcm63xx/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
target/linux/brcm63xx/base-files/etc/uci-defaults/01_leds
target/linux/brcm63xx/base-files/etc/uci-defaults/02_network
target/linux/brcm63xx/base-files/lib/brcm63xx.sh
target/linux/brcm63xx/dts/hg655b.dts [new file with mode: 0644]
target/linux/brcm63xx/image/Makefile
target/linux/brcm63xx/patches-3.18/570-board_HG655b.patch [new file with mode: 0644]
target/linux/brcm63xx/profiles/huawei.mk

index 03d98b9..c330674 100644 (file)
@@ -89,6 +89,9 @@ set_state() {
        hg520)
                status_led="HW520:green:net"
                ;;
+       hg655b)
+               status_led="HW65x:green:power"
+               ;;
        p870hw-51a_v2)
                status_led="P870HW-51a:green:power"
                ;;
index 9a324ea..4347485 100644 (file)
@@ -34,6 +34,9 @@ case "$FIRMWARE" in
        hg556a_c)
                rt2x00_eeprom_extract "cal_data" 130560 512
                ;;
+       hg655b)
+               rt2x00_eeprom_extract "cal_data" 0 512
+               ;;
        *)
                rt2x00_eeprom_die "board $board is not supported yet"
                ;;
index 58404a1..b964bdb 100644 (file)
@@ -34,6 +34,9 @@ hg556a_*)
        ucidef_set_led_netdev "lan" "LAN" "HW556:red:dsl" "eth0"
        ucidef_set_led_usbdev "usb" "USB" "HW556:red:hspa" "1-2"
        ;;
+hg655b)
+       ucidef_set_led_usbdev "usb" "USB" "HW65x:green:usb" "1-2"
+       ;;
 homehub2a)
        ucidef_set_led_netdev "lan" "LAN" "HOMEHUB2A:blue:broadband" "eth0.1"
        ucidef_set_led_netdev "wlan0" "WIFI" "HOMEHUB2A:green:wireless" "wlan0"
index 814e100..e5880eb 100644 (file)
@@ -92,6 +92,7 @@ dsl-274xb-f |\
 dsl-275xb-d |\
 fast2504n |\
 fast2704v2 |\
+hg655b |\
 p870hw-51a_v2 |\
 vr-3025un |\
 vr-3025u)
index 5cb390f..0eb9a75 100755 (executable)
@@ -156,6 +156,9 @@ brcm63xx_dt_detect() {
        "Huawei EchoLife HG556a (version C)")
                board_name="hg556a_c"
                ;;
+       "Huawei HG655b")
+               board_name="hg655b"
+               ;;
        "Inteno VG50")
                board_name="vg50"
                ;;
diff --git a/target/linux/brcm63xx/dts/hg655b.dts b/target/linux/brcm63xx/dts/hg655b.dts
new file mode 100644 (file)
index 0000000..256233d
--- /dev/null
@@ -0,0 +1,110 @@
+/dts-v1/;
+
+/include/ "bcm6368.dtsi"
+
+/ {
+       model = "Huawei HG655b";
+       compatible = "huawei,hg655b", "brcm,bcm6368";
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+               debounce-interval = <60>;
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio0 12 1>;
+                       linux,code = <0x211>;
+               };
+               wlan {
+                       label = "wlan";
+                       gpios = <&gpio0 23 1>;
+                       linux,code = <0xee>;
+               };
+               reset {
+                       label = "reset";
+                       gpios = <&gpio1 2 1>;
+                       linux,code = <0x198>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               dsl_green {
+                       label = "HW65x:green:dsl";
+                       gpios = <&gpio0 2 1>;
+               };
+               internet_green {
+                       label = "HW65x:green:internet";
+                       gpios = <&gpio0 5 1>;
+               };
+               lan1_green {
+                       label = "HW65x:green:lan1";
+                       gpios = <&gpio0 6 1>;
+               };
+               lan2_green {
+                       label = "HW65x:green:lan2";
+                       gpios = <&gpio0 7 1>;
+               };
+               lan3_green {
+                       label = "HW65x:green:lan3";
+                       gpios = <&gpio0 8 1>;
+               };
+               lan4_green {
+                       label = "HW65x:green:lan4";
+                       gpios = <&gpio0 9 1>;
+               };
+               usb_green {
+                       label = "HW65x:green:usb";
+                       gpios = <&gpio0 14 1>;
+               };
+               power_green {
+                       label = "HW65x:green:power";
+                       gpios = <&gpio0 22 1>;
+                       default-state = "on";
+               };
+               voip_green {
+                       label = "HW65x:green:voip";
+                       gpios = <&gpio0 25 1>;
+               };
+               wps_green {
+                       label = "HW65x:green:wps";
+                       gpios = <&gpio0 27 1>;
+               };
+       };
+};
+
+&pflash {
+       status = "ok";
+
+       linux,part-probe = "bcm63xxpart";
+
+       cfe@0 {
+               label = "CFE";
+               reg = <0x000000 0x020000>;
+       };
+
+       linux@20000 {
+               label = "linux";
+               reg = <0x020000 0x770000>;
+       };
+
+       board_data@790000 {
+               label = "board_data";
+               reg = <0x790000 0x030000>;
+       };
+
+       cal_data@7c0000 {
+               label = "cal_data";
+               reg = <0x7c0000 0x020000>;
+               read-only;
+       };
+
+       nvram@7d0000 {
+               label = "nvram";
+               reg = <0x7e0000 0x020000>;
+       };
+};
index e98011d..0d8ce53 100755 (executable)
@@ -360,6 +360,8 @@ $(eval $(call ImageDTB,CFEDTB,HG553,HG553,hg553,HW553,6358,--rsa-signature "Echo
 $(eval $(call ImageDTB,CFEDTB,HG556a_AB,HG556a_A,hg556a-a,HW556,6358,--rsa-signature "EchoLife_HG556a" --image-offset 0x20000 --block-size 0x10000 --tag-version 8))
 $(eval $(call ImageDTB,CFEDTB,HG556a_AB,HG556a_B,hg556a-b,HW556,6358,--rsa-signature "EchoLife_HG556a" --image-offset 0x20000 --block-size 0x20000 --tag-version 8))
 $(eval $(call ImageDTB,CFEDTB,HG556a_C,HG556a_C,hg556a-c,HW556,6358,--rsa-signature "EchoLife_HG556a" --image-offset 0x20000 --block-size 0x20000 --tag-version 8))
+# Huawei HG655b
+$(eval $(call ImageDTB,CFEDTB,HG655b,HG655b,hg655b,HW65x,6368,--image-offset 0x20000 --tag-version 7 --pad 4))
 # Inteno VG50
 $(eval $(call ImageDTB,Dummy,VG50,vg50,vg50,VW6339GU,63268))
 # Inventel Livebox 1
diff --git a/target/linux/brcm63xx/patches-3.18/570-board_HG655b.patch b/target/linux/brcm63xx/patches-3.18/570-board_HG655b.patch
new file mode 100644 (file)
index 0000000..903068a
--- /dev/null
@@ -0,0 +1,72 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1928,6 +1928,53 @@
+       .spis = DGND3700v1_3800B_spi_devices,
+       .num_spis = ARRAY_SIZE(DGND3700v1_3800B_spi_devices),
++};
++
++static struct board_info __initdata board_HG655b = {
++      .name                           = "HW65x",
++      .expected_cpu_id                = 0x6368,
++
++      .has_uart0                      = 1,
++      .has_pci                        = 1,
++      .has_ohci0                      = 1,
++      .has_ehci0                      = 1,
++      .num_usbh_ports                 = 2,
++
++      .has_caldata                    = 1,
++      .caldata = {
++              {
++                      .vendor                 = PCI_VENDOR_ID_RALINK,
++                      .caldata_offset         = 0x7c0000,
++                      .slot                   = 1,
++                      .eeprom                 = "rt2x00.eeprom",
++              },
++      },
++
++      .has_enetsw                     = 1,
++      .enetsw = {
++              .used_ports = {
++                      [0] = {
++                              .used           = 1,
++                              .phy_id         = 1,
++                              .name           = "port1",
++                      },
++                      [1] = {
++                              .used           = 1,
++                              .phy_id         = 2,
++                              .name           = "port2",
++                      },
++                      [2] = {
++                              .used           = 1,
++                              .phy_id         = 3,
++                              .name           = "port3",
++                      },
++                      [3] = {
++                              .used           = 1,
++                              .phy_id         = 4,
++                              .name           = "port4",
++                      },
++              },
++      },
+ };
+ static struct sprom_fixup __initdata vr3025u_fixups[] = {
+@@ -2380,6 +2427,7 @@
+       &board_96368mvwg,
+       &board_96368mvngr,
+       &board_DGND3700v1_3800B,
++      &board_HG655b,
+       &board_P870HW51A_V2,
+       &board_VR3025u,
+       &board_VR3025un,
+@@ -2483,6 +2531,7 @@
+       { .compatible = "comtrend,vr-3025u", .data = &board_VR3025u, },
+       { .compatible = "comtrend,vr-3025un", .data = &board_VR3025un, },
+       { .compatible = "comtrend,wap-5813n", .data = &board_WAP5813n, },
++      { .compatible = "huawei,hg655b", .data = &board_HG655b, },
+       { .compatible = "netgear,dgnd3700v1", .data = &board_DGND3700v1_3800B, },
+       { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, },
+ #endif
index 594389e..a6764b7 100644 (file)
@@ -43,3 +43,13 @@ define Profile/HG556a_C/Description
   Package set optimized for Huawei HG556a version C (Ralink).
 endef
 $(eval $(call Profile,HG556a_C))
+
+define Profile/HG655b
+  NAME:=Huawei HG655b
+  PACKAGES:=kmod-rt2800-pci wpad-mini \
+       kmod-usb2 kmod-usb-ohci kmod-ledtrig-usbdev
+endef
+define Profile/HG655b/Description
+  Package set optimized for Huawei HG655b, HG655d.
+endef
+$(eval $(call Profile,HG655b))