ath10k: increase bmi timeout to fix OTP on qca99xx boards and add bmi identification...
authorPavel Kubelun <be.dissent@gmail.com>
Thu, 1 Jun 2017 14:13:04 +0000 (17:13 +0300)
committerFelix Fietkau <nbd@nbd.name>
Sat, 17 Jun 2017 09:51:41 +0000 (11:51 +0200)
Backporting upstream patches.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [refresh, rename patches]
package/kernel/mac80211/patches/327-ath10k-increase-BMI-timeout.patch [new file with mode: 0644]
package/kernel/mac80211/patches/328-ath10k-log-when-longer-bmi-cmds-happen.patch [new file with mode: 0644]
package/kernel/mac80211/patches/329-ath10k-add-BMI-parameters-to-fix-calibration-from-DT.patch [new file with mode: 0644]
package/kernel/mac80211/patches/921-ath10k_init_devices_synchronously.patch
package/kernel/mac80211/patches/936-ath10k-fix-otp-failure-result.patch
package/kernel/mac80211/patches/960-0010-ath10k-limit-htt-rx-ring-size.patch
package/kernel/mac80211/patches/960-0011-ath10k-limit-pci-buffer-size.patch

diff --git a/package/kernel/mac80211/patches/327-ath10k-increase-BMI-timeout.patch b/package/kernel/mac80211/patches/327-ath10k-increase-BMI-timeout.patch
new file mode 100644 (file)
index 0000000..c9f493b
--- /dev/null
@@ -0,0 +1,31 @@
+From: Ben Greear <greearb@candelatech.com>
+Date: Wed, 31 May 2017 14:21:19 +0300
+Subject: [PATCH] ath10k: increase BMI timeout
+
+When testing a 9888 chipset NIC, I notice it often takes
+almost 2 seconds, and then many times OTP fails, probably due
+to the two-second timeout.
+
+[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
+[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
+[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0
+
+So, increase the BMI timeout to 3 seconds.
+
+Signed-off-by: Ben Greear <greearb@candelatech.com>
+Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
+---
+
+--- a/drivers/net/wireless/ath/ath10k/bmi.h
++++ b/drivers/net/wireless/ath/ath10k/bmi.h
+@@ -187,8 +187,8 @@ struct bmi_target_info {
+       u32 type;
+ };
+-/* in msec */
+-#define BMI_COMMUNICATION_TIMEOUT_HZ (2 * HZ)
++/* in jiffies */
++#define BMI_COMMUNICATION_TIMEOUT_HZ (3 * HZ)
+ #define BMI_CE_NUM_TO_TARG 0
+ #define BMI_CE_NUM_TO_HOST 1
diff --git a/package/kernel/mac80211/patches/328-ath10k-log-when-longer-bmi-cmds-happen.patch b/package/kernel/mac80211/patches/328-ath10k-log-when-longer-bmi-cmds-happen.patch
new file mode 100644 (file)
index 0000000..500f72f
--- /dev/null
@@ -0,0 +1,74 @@
+From: Ben Greear <greearb@candelatech.com>
+Date: Wed, 31 May 2017 14:21:21 +0300
+Subject: [PATCH] ath10k: log when longer bmi cmds happen
+
+This lets one have a clue that maybe timeouts are happening
+when we just aren't waiting long enough.
+
+Signed-off-by: Ben Greear <greearb@candelatech.com>
+Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
+---
+
+--- a/drivers/net/wireless/ath/ath10k/pci.c
++++ b/drivers/net/wireless/ath/ath10k/pci.c
+@@ -101,7 +101,8 @@ static int ath10k_pci_init_irq(struct at
+ static int ath10k_pci_deinit_irq(struct ath10k *ar);
+ static int ath10k_pci_request_irq(struct ath10k *ar);
+ static void ath10k_pci_free_irq(struct ath10k *ar);
+-static int ath10k_pci_bmi_wait(struct ath10k_ce_pipe *tx_pipe,
++static int ath10k_pci_bmi_wait(struct ath10k *ar,
++                             struct ath10k_ce_pipe *tx_pipe,
+                              struct ath10k_ce_pipe *rx_pipe,
+                              struct bmi_xfer *xfer);
+ static int ath10k_pci_qca99x0_chip_reset(struct ath10k *ar);
+@@ -1843,7 +1844,7 @@ int ath10k_pci_hif_exchange_bmi_msg(stru
+       if (ret)
+               goto err_resp;
+-      ret = ath10k_pci_bmi_wait(ce_tx, ce_rx, &xfer);
++      ret = ath10k_pci_bmi_wait(ar, ce_tx, ce_rx, &xfer);
+       if (ret) {
+               u32 unused_buffer;
+               unsigned int unused_nbytes;
+@@ -1910,23 +1911,37 @@ static void ath10k_pci_bmi_recv_data(str
+       xfer->rx_done = true;
+ }
+-static int ath10k_pci_bmi_wait(struct ath10k_ce_pipe *tx_pipe,
++static int ath10k_pci_bmi_wait(struct ath10k *ar,
++                             struct ath10k_ce_pipe *tx_pipe,
+                              struct ath10k_ce_pipe *rx_pipe,
+                              struct bmi_xfer *xfer)
+ {
+       unsigned long timeout = jiffies + BMI_COMMUNICATION_TIMEOUT_HZ;
++      unsigned long started = jiffies;
++      unsigned long dur;
++      int ret;
+       while (time_before_eq(jiffies, timeout)) {
+               ath10k_pci_bmi_send_done(tx_pipe);
+               ath10k_pci_bmi_recv_data(rx_pipe);
+-              if (xfer->tx_done && (xfer->rx_done == xfer->wait_for_resp))
+-                      return 0;
++              if (xfer->tx_done && (xfer->rx_done == xfer->wait_for_resp)) {
++                      ret = 0;
++                      goto out;
++              }
+               schedule();
+       }
+-      return -ETIMEDOUT;
++      ret = -ETIMEDOUT;
++
++out:
++      dur = jiffies - started;
++      if (dur > HZ)
++              ath10k_dbg(ar, ATH10K_DBG_BMI,
++                         "bmi cmd took %lu jiffies hz %d ret %d\n",
++                         dur, HZ, ret);
++      return ret;
+ }
+ /*
diff --git a/package/kernel/mac80211/patches/329-ath10k-add-BMI-parameters-to-fix-calibration-from-DT.patch b/package/kernel/mac80211/patches/329-ath10k-add-BMI-parameters-to-fix-calibration-from-DT.patch
new file mode 100644 (file)
index 0000000..3fcf505
--- /dev/null
@@ -0,0 +1,80 @@
+From: Anilkumar Kolli <akolli@qti.qualcomm.com>
+Date: Wed, 31 May 2017 14:21:27 +0300
+Subject: [PATCH] ath10k: add BMI parameters to fix calibration from
+ DT/pre-cal
+
+QCA99X0, QCA9888, QCA9984 supports calibration data in
+either OTP or DT/pre-cal file. Current ath10k supports
+Calibration data from OTP only.
+
+If caldata is loaded from DT/pre-cal file, fetching board id
+and applying calibration parameters like tx power gets failed.
+
+error log:
+[   15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
+[   15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)
+
+This patch adds calibration data support from DT/pre-cal
+file.  Below parameters are used to get board id and
+applying calibration parameters from cal data.
+
+               EEPROM[OTP]     FLASH[DT/pre-cal file]
+Cal param      0x700           0x10000
+Board id       0x10            0x8000
+
+Tested on QCA9888 with pre-cal file.
+
+Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
+Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
+---
+
+--- a/drivers/net/wireless/ath/ath10k/bmi.h
++++ b/drivers/net/wireless/ath/ath10k/bmi.h
+@@ -83,6 +83,8 @@ enum bmi_cmd_id {
+ #define BMI_NVRAM_SEG_NAME_SZ 16
+ #define BMI_PARAM_GET_EEPROM_BOARD_ID 0x10
++#define BMI_PARAM_GET_FLASH_BOARD_ID 0x8000
++#define BMI_PARAM_FLASH_SECTION_ALL 0x10000
+ #define ATH10K_BMI_BOARD_ID_FROM_OTP_MASK   0x7c00
+ #define ATH10K_BMI_BOARD_ID_FROM_OTP_LSB    10
+--- a/drivers/net/wireless/ath/ath10k/core.c
++++ b/drivers/net/wireless/ath/ath10k/core.c
+@@ -657,7 +657,7 @@ static int ath10k_core_get_board_id_from
+ {
+       u32 result, address;
+       u8 board_id, chip_id;
+-      int ret;
++      int ret, bmi_board_id_param;
+       address = ar->hw_params.patch_load_addr;
+@@ -681,8 +681,13 @@ static int ath10k_core_get_board_id_from
+               return ret;
+       }
+-      ret = ath10k_bmi_execute(ar, address, BMI_PARAM_GET_EEPROM_BOARD_ID,
+-                               &result);
++      if (ar->cal_mode == ATH10K_PRE_CAL_MODE_DT ||
++          ar->cal_mode == ATH10K_PRE_CAL_MODE_FILE)
++              bmi_board_id_param = BMI_PARAM_GET_FLASH_BOARD_ID;
++      else
++              bmi_board_id_param = BMI_PARAM_GET_EEPROM_BOARD_ID;
++
++      ret = ath10k_bmi_execute(ar, address, bmi_board_id_param, &result);
+       if (ret) {
+               ath10k_err(ar, "could not execute otp for board id check: %d\n",
+                          ret);
+@@ -810,6 +815,11 @@ static int ath10k_download_and_run_otp(s
+               return ret;
+       }
++      /* As of now pre-cal is valid for 10_4 variants */
++      if (ar->cal_mode == ATH10K_PRE_CAL_MODE_DT ||
++          ar->cal_mode == ATH10K_PRE_CAL_MODE_FILE)
++              bmi_otp_exe_param = BMI_PARAM_FLASH_SECTION_ALL;
++
+       ret = ath10k_bmi_execute(ar, address, bmi_otp_exe_param, &result);
+       if (ret) {
+               ath10k_err(ar, "could not execute otp (%d)\n", ret);
index 0c34d96847a0110779e59f4572bcfd8a1723417d..b966516e577217d60f732f56d2f3a6cabbd90864 100644 (file)
@@ -14,7 +14,7 @@ Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
 
 --- a/drivers/net/wireless/ath/ath10k/core.c
 +++ b/drivers/net/wireless/ath/ath10k/core.c
-@@ -2319,6 +2319,16 @@ int ath10k_core_register(struct ath10k *
+@@ -2329,6 +2329,16 @@ int ath10k_core_register(struct ath10k *
        ar->chip_id = chip_id;
        queue_work(ar->workqueue, &ar->register_work);
  
index e28fa8fa60dac18615962f57a5e677bfcf59b660..d302a7d2a3ad7b32db3d83c0438cb606f9d85c99 100644 (file)
@@ -1,6 +1,6 @@
 --- a/drivers/net/wireless/ath/ath10k/core.c
 +++ b/drivers/net/wireless/ath/ath10k/core.c
-@@ -686,7 +686,7 @@
+@@ -691,7 +691,7 @@ static int ath10k_core_get_board_id_from
        if (ret) {
                ath10k_err(ar, "could not execute otp for board id check: %d\n",
                           ret);
index e36f13b19525deddabb05c19e9c9e0cddf8f79e4..d49be4df703e8039509ecea23de8b5bd8e590765 100644 (file)
@@ -1,11 +1,11 @@
---- a/drivers/net/wireless/ath/ath10k/htt.h    2016-12-12 16:03:58.491019030 +0100
-+++ b/drivers/net/wireless/ath/ath10k/htt.h    2016-12-12 15:39:45.242298155 +0100
+--- a/drivers/net/wireless/ath/ath10k/htt.h
++++ b/drivers/net/wireless/ath/ath10k/htt.h
 @@ -199,7 +199,7 @@ enum htt_rx_ring_flags {
  };
  
  #define HTT_RX_RING_SIZE_MIN 128
-+#define HTT_RX_RING_SIZE_MAX 512
 -#define HTT_RX_RING_SIZE_MAX 2048
++#define HTT_RX_RING_SIZE_MAX 512
  
  struct htt_rx_ring_setup_ring {
        __le32 fw_idx_shadow_reg_paddr;
index 0bdddaeef82d65c4cbd278833cbdd043591b887a..a101282d074aeba592b042dcc9944c2a260e40ba 100644 (file)
@@ -1,6 +1,6 @@
---- a/drivers/net/wireless/ath/ath10k/pci.c    2016-12-12 16:29:42.310053558 +0100
-+++ b/drivers/net/wireless/ath/ath10k/pci.c    2016-12-12 16:34:46.667203800 +0100
-@@ -127,7 +127,7 @@ static struct ce_attr host_ce_config_wla
+--- a/drivers/net/wireless/ath/ath10k/pci.c
++++ b/drivers/net/wireless/ath/ath10k/pci.c
+@@ -128,7 +128,7 @@ static struct ce_attr host_ce_config_wla
                .flags = CE_ATTR_FLAGS,
                .src_nentries = 0,
                .src_sz_max = 2048,
@@ -9,7 +9,7 @@
                .recv_cb = ath10k_pci_htt_htc_rx_cb,
        },
  
-@@ -136,7 +136,7 @@ static struct ce_attr host_ce_config_wla
+@@ -137,7 +137,7 @@ static struct ce_attr host_ce_config_wla
                .flags = CE_ATTR_FLAGS,
                .src_nentries = 0,
                .src_sz_max = 2048,
@@ -18,7 +18,7 @@
                .recv_cb = ath10k_pci_htc_rx_cb,
        },
  
-@@ -163,7 +163,7 @@ static struct ce_attr host_ce_config_wla
+@@ -164,7 +164,7 @@ static struct ce_attr host_ce_config_wla
                .flags = CE_ATTR_FLAGS,
                .src_nentries = 0,
                .src_sz_max = 512,
@@ -27,7 +27,7 @@
                .recv_cb = ath10k_pci_htt_rx_cb,
        },
  
-@@ -188,7 +188,7 @@ static struct ce_attr host_ce_config_wla
+@@ -189,7 +189,7 @@ static struct ce_attr host_ce_config_wla
                .flags = CE_ATTR_FLAGS,
                .src_nentries = 0,
                .src_sz_max = 2048,