+# SPDX-License-Identifier: GPL-2.0-only
#
# Copyright (C) 2009-2013 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
KERNEL_LOADADDR:=0x8000
+# Some info about Ctera firmware:
+# 1. It's simple tar file (GNU standard), but it must have ".firm" suffix.
+# 2. It contains two images: kernel and romdisk. Both are required.
+# 3. Every image has header and trailer file.
+# 4. The struct of tar firmware is: header kernel trailer header romdisk trailer
+# 5. In header file are some strings used to describe image. It was decoded from
+# factory image.
+# 6. Version format in header file is restricted by Original FW.
+# 7. Trailer file contains MD5 sum string of header and image file.
+# 8. Firmware file must have <=24MB size.
+
+define Build/ctera-firmware
+ mkdir -p $@.tmp
+
+ # Prepare header and trailer file for kernel
+ echo "# CTera firmware information file" > $@.tmp/header
+ echo "image_type=kernel" >> $@.tmp/header
+ echo "arch=Kirkwood" >> $@.tmp/header
+ echo "board=Any" >> $@.tmp/header
+ echo "version=3.1.22.30669" >> $@.tmp/header
+ echo "kernel_cmd=console=ttyS0,115200 earlyprintk" >> $@.tmp/header
+ echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
+ >> $@.tmp/header
+
+ cp $@ $@.tmp/kernel
+
+ echo "MD5=$$(cat $@.tmp/header $@.tmp/kernel | $(MKHASH) md5)" \
+ > $@.tmp/trailer
+
+ tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
+ -H gnu -C $@.tmp -cf $@.tar header kernel trailer
+
+ # Prepare header and trailer file for fake romdisk
+ echo "# CTera firmware information file" > $@.tmp/header
+ echo "image_type=romdisk" >> $@.tmp/header
+ echo "initrd=yes" >> $@.tmp/header
+ echo "arch=Kirkwood" >> $@.tmp/header
+ echo "board=Any" >> $@.tmp/header
+ echo "version=3.1.22.30669" >> $@.tmp/header
+ echo "date=$$(date $(if $(SOURCE_DATE_EPOCH),-d@$(SOURCE_DATE_EPOCH)))" \
+ >> $@.tmp/header
+
+ rm -f $@
+ touch $@
+ $(call Build/append-uImage-fakehdr, ramdisk)
+ cp $@ $@.tmp/romdisk
+
+ echo "MD5=$$(cat $@.tmp/header $@.tmp/romdisk | $(MKHASH) md5)" \
+ > $@.tmp/trailer
+
+ tar $(if $(SOURCE_DATE_EPOCH),--mtime="@$(SOURCE_DATE_EPOCH)") \
+ -H gnu -C $@.tmp -rf $@.tar header romdisk trailer
+
+ mv $@.tar $@
+ rm -rf $@.tmp
+endef
+
+define Device/kernel-size-migration
+ DEVICE_COMPAT_VERSION := 2.0
+ DEVICE_COMPAT_MESSAGE := Partition design has changed compared to \
+ older versions (up to 21.02) due to kernel size restrictions. \
+ Upgrade via sysupgrade mechanism is not possible, so new \
+ installation via factory style image is required.
+endef
+
define Device/Default
PROFILES := Default
+ DEVICE_DTS = kirkwood-$(lastword $(subst _, ,$(1)))
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL := kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
- SUPPORTED_DEVICES := $(1)
endef
-define Device/dockstar
- DEVICE_DTS := kirkwood-dockstar
- DEVICE_TITLE := Seagate FreeAgent Dockstar
- SUPPORTED_DEVICES += seagate,dockstar
+define Device/checkpoint_l-50
+ DEVICE_VENDOR := Check Point
+ DEVICE_MODEL := L-50
+ DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
+ kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic-mbedtls
+ IMAGES := sysupgrade.bin
endef
-TARGET_DEVICES += dockstar
+TARGET_DEVICES += checkpoint_l-50
-define Device/goflexnet
- DEVICE_TITLE := Seagate GoFlexNet
- DEVICE_DTS := kirkwood-goflexnet
- SUPPORTED_DEVICES += seagate,goflexnet
+define Device/cisco_on100
+ DEVICE_VENDOR := Cisco Systems
+ DEVICE_MODEL := ON100
+ KERNEL_SIZE := 5376k
+ KERNEL_IN_UBI :=
+ UBINIZE_OPTS := -E 5
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
+ DEVICE_PACKAGES := kmod-mvsdio
+ SUPPORTED_DEVICES += on100
endef
-TARGET_DEVICES += goflexnet
+TARGET_DEVICES += cisco_on100
-define Device/goflexhome
- DEVICE_TITLE := Seagate GoFlexHome
- DEVICE_DTS := kirkwood-goflexhome
- SUPPORTED_DEVICES += seagate,goflexhome
+define Device/cloudengines_pogoe02
+ DEVICE_VENDOR := Cloud Engines
+ DEVICE_MODEL := Pogoplug E02
+ DEVICE_DTS := kirkwood-pogo_e02
+ SUPPORTED_DEVICES += pogo_e02
endef
-TARGET_DEVICES += goflexhome
+TARGET_DEVICES += cloudengines_pogoe02
-define Device/linksys-audi
- DEVICE_TITLE := Linksys EA3500 (Audi)
- DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-mini
- DEVICE_DTS := kirkwood-linksys-audi
- KERNEL_SIZE := 2624k
- KERNEL_IN_UBI := 0
- UBINIZE_OPTS := -E 5
- IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
- SUPPORTED_DEVICES += linksys,audi
+define Device/cloudengines_pogoplugv4
+ DEVICE_VENDOR := Cloud Engines
+ DEVICE_MODEL := Pogoplug V4
+ DEVICE_DTS := kirkwood-pogoplug-series-4
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-mvsdio kmod-usb3 \
+ kmod-gpio-button-hotplug
endef
-TARGET_DEVICES += linksys-audi
+TARGET_DEVICES += cloudengines_pogoplugv4
-define Device/linksys-viper
- DEVICE_TITLE := Linksys E4200v2 / EA4500 (Viper)
- DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-mini
- DEVICE_DTS := kirkwood-linksys-viper
- KERNEL_SIZE := 2688k
- KERNEL_IN_UBI := 0
- UBINIZE_OPTS := -E 5
- IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
- SUPPORTED_DEVICES += linksys,viper
+define Device/ctera_c200-v1
+ DEVICE_VENDOR := Ctera
+ DEVICE_MODEL := C200
+ DEVICE_VARIANT := V1
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-gpio-button-hotplug \
+ kmod-hwmon-lm63 kmod-rtc-s35390a kmod-usb-ledtrig-usbport
+ KERNEL := kernel-bin | append-dtb | uImage none | ctera-firmware
+ KERNEL_IN_UBI :=
+ KERNEL_SUFFIX := -factory.firm
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += ctera_c200-v1
+
+define Device/endian_4i-edge-200
+ DEVICE_VENDOR := Endian
+ DEVICE_MODEL := 4i Edge 200
+ DEVICE_ALT0_VENDOR := Endian
+ DEVICE_ALT0_MODEL := UTM Mini Firewall
+ DEVICE_PACKAGES := kmod-ath9k kmod-mvsdio wpad-basic-mbedtls
+ KERNEL_SIZE := 4096k
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += endian_4i-edge-200
+
+define Device/globalscale_sheevaplug
+ DEVICE_VENDOR := Globalscale
+ DEVICE_MODEL := Sheevaplug
+ DEVICE_PACKAGES := kmod-mvsdio
endef
-TARGET_DEVICES += linksys-viper
+TARGET_DEVICES += globalscale_sheevaplug
-define Device/iconnect
- DEVICE_TITLE := Iomega Iconnect
+define Device/iom_iconnect-1.1
+ DEVICE_VENDOR := Iomega
+ DEVICE_MODEL := Iconnect
DEVICE_DTS := kirkwood-iconnect
- SUPPORTED_DEVICES += iom,iconnect-1.1
+ SUPPORTED_DEVICES += iconnect
endef
-TARGET_DEVICES += iconnect
+TARGET_DEVICES += iom_iconnect-1.1
-define Device/nsa310b
- DEVICE_TITLE := ZyXEL NSA310b
- DEVICE_DTS := kirkwood-nsa310b
- DEVICE_PACKAGES := kmod-r8169 kmod-gpio-button-hotplug kmod-hwmon-lm85
- SUPPORTED_DEVICES += zyxel,nsa310b
+define Device/iom_ix2-200
+ DEVICE_VENDOR := Iomega
+ DEVICE_MODEL := StorCenter ix2-200
+ DEVICE_DTS := kirkwood-iomega_ix2_200
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+ kmod-gpio-button-hotplug kmod-hwmon-lm63
+ PAGESIZE := 512
+ SUBPAGESIZE := 256
+ BLOCKSIZE := 16k
+ KERNEL_SIZE := 3072k
+ KERNEL_IN_UBI :=
+ UBINIZE_OPTS := -E 5
+ IMAGE_SIZE := 31744k
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
+ check-size
endef
-TARGET_DEVICES += nsa310b
+TARGET_DEVICES += iom_ix2-200
-define Device/nsa325
- DEVICE_TITLE := ZyXEL NSA325 (v1 and v2)
- DEVICE_DTS := kirkwood-nsa325
- DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
- SUPPORTED_DEVICES += zyxel,nsa325
+define Device/iom_ix4-200d
+ DEVICE_VENDOR := Iomega
+ DEVICE_MODEL := StorCenter ix4-200d
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+ kmod-gpio-button-hotplug kmod-gpio-nxp-74hc164 \
+ kmod-hwmon-adt7475 kmod-mvsdio kmod-spi-gpio
+ PAGESIZE := 512
+ SUBPAGESIZE := 256
+ BLOCKSIZE := 16k
+ KERNEL_SIZE := 3072k
+ KERNEL_IN_UBI :=
+ UBINIZE_OPTS := -E 5
+ IMAGE_SIZE := 31744k
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
+ check-size
endef
-TARGET_DEVICES += nsa325
+TARGET_DEVICES += iom_ix4-200d
-define Device/on100
- DEVICE_TITLE := Cisco Systems ON100
- DEVICE_DTS := kirkwood-on100
- DEVICE_PACKAGES := kmod-i2c-mv64xxx
- KERNEL_SIZE := 5376k
- KERNEL_IN_UBI := 0
+define Device/iptime_nas1
+ DEVICE_VENDOR := ipTIME
+ DEVICE_MODEL := NAS1
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+ kmod-gpio-button-hotplug kmod-gpio-pca953x kmod-hwmon-drivetemp \
+ kmod-hwmon-gpiofan kmod-usb-ledtrig-usbport -uboot-envtools
+ KERNEL := $$(KERNEL) | iptime-naspkg nas1
+ BLOCKSIZE := 256k
+ IMAGE_SIZE := 15872k
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | \
+ check-size | append-metadata
+endef
+TARGET_DEVICES += iptime_nas1
+
+define Device/linksys
+ DEVICE_VENDOR := Linksys
+ DEVICE_PACKAGES := kmod-mwl8k wpad-basic-mbedtls kmod-gpio-button-hotplug
+ KERNEL_IN_UBI :=
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
- SUPPORTED_DEVICES := cisco,on100
endef
-TARGET_DEVICES += on100
-define Device/pogo_e02
- DEVICE_TITLE := Cloud Engines Pogoplug E02
- DEVICE_DTS := kirkwood-pogo_e02
- SUPPORTED_DEVICES += cloudengines,pogoe02
+define Device/linksys_e4200-v2
+ $(Device/linksys)
+ $(Device/kernel-size-migration)
+ DEVICE_MODEL := E4200
+ DEVICE_VARIANT := v2
+ KERNEL_SIZE := 3072k
+ SUPPORTED_DEVICES += linksys,viper linksys-viper
endef
-TARGET_DEVICES += pogo_e02
+TARGET_DEVICES += linksys_e4200-v2
-define Device/ib62x0
- DEVICE_TITLE := RaidSonic ICY BOX IB-NAS62x0
+define Device/linksys_ea3500
+ $(Device/linksys)
+ $(Device/kernel-size-migration)
+ DEVICE_MODEL := EA3500
+ PAGESIZE := 512
+ SUBPAGESIZE := 256
+ BLOCKSIZE := 16k
+ KERNEL_SIZE := 3072k
+ SUPPORTED_DEVICES += linksys,audi linksys-audi
+endef
+TARGET_DEVICES += linksys_ea3500
+
+define Device/linksys_ea4500
+ $(Device/linksys)
+ $(Device/kernel-size-migration)
+ DEVICE_MODEL := EA4500
+ KERNEL_SIZE := 3072k
+ SUPPORTED_DEVICES += linksys,viper linksys-viper
+endef
+TARGET_DEVICES += linksys_ea4500
+
+define Device/netgear_readynas-duo-v2
+ DEVICE_VENDOR := NETGEAR
+ DEVICE_MODEL := ReadyNAS Duo
+ DEVICE_VARIANT := v2
+ DEVICE_DTS := kirkwood-netgear_readynas_duo_v2
+ KERNEL_IN_UBI :=
+ IMAGES := sysupgrade.bin
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+ kmod-gpio-button-hotplug kmod-hwmon-g762 kmod-rtc-rs5c372a kmod-usb3
+endef
+TARGET_DEVICES += netgear_readynas-duo-v2
+
+define Device/raidsonic_ib-nas62x0
+ DEVICE_VENDOR := RaidSonic
+ DEVICE_MODEL := ICY BOX IB-NAS62x0
DEVICE_DTS := kirkwood-ib62x0
- SUPPORTED_DEVICES += raidsonic,ib-nas62x0
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
+ SUPPORTED_DEVICES += ib62x0
+endef
+TARGET_DEVICES += raidsonic_ib-nas62x0
+
+define Device/seagate_blackarmor-nas220
+ DEVICE_VENDOR := Seagate
+ DEVICE_MODEL := Blackarmor NAS220
+ DEVICE_PACKAGES := kmod-hwmon-adt7475 kmod-fs-ext4 kmod-ata-marvell-sata \
+ mdadm kmod-gpio-button-hotplug
+ PAGESIZE := 512
+ SUBPAGESIZE := 256
+ BLOCKSIZE := 16k
+ UBINIZE_OPTS := -e 1
+endef
+TARGET_DEVICES += seagate_blackarmor-nas220
+
+define Device/seagate_dockstar
+ DEVICE_VENDOR := Seagate
+ DEVICE_MODEL := FreeAgent Dockstar
+ SUPPORTED_DEVICES += dockstar
+endef
+TARGET_DEVICES += seagate_dockstar
+
+define Device/seagate_goflexnet
+ DEVICE_VENDOR := Seagate
+ DEVICE_MODEL := GoFlexNet
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
+ SUPPORTED_DEVICES += goflexnet
+endef
+TARGET_DEVICES += seagate_goflexnet
+
+define Device/seagate_goflexhome
+ DEVICE_VENDOR := Seagate
+ DEVICE_MODEL := GoFlexHome
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
+ SUPPORTED_DEVICES += goflexhome
+endef
+TARGET_DEVICES += seagate_goflexhome
+
+define Device/zyxel_nsa310b
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := NSA310b
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-r8169 kmod-fs-ext4 \
+ kmod-gpio-button-hotplug kmod-hwmon-lm85
+ SUPPORTED_DEVICES += nsa310b
+endef
+TARGET_DEVICES += zyxel_nsa310b
+
+define Device/zyxel_nsa310s
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := NSA310S
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug
+endef
+TARGET_DEVICES += zyxel_nsa310s
+
+define Device/zyxel_nsa325
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := NSA325
+ DEVICE_VARIANT := v1/v2
+ DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+ kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
+ SUPPORTED_DEVICES += nsa325
endef
-TARGET_DEVICES += ib62x0
+TARGET_DEVICES += zyxel_nsa325
$(eval $(call BuildImage))