target/linux/ath79/dts/ar7161_netgear_wndr3800.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar7100.dtsi"
   8
   9 / {
  10         compatible = "netgear,wndr3800", "qca,ar7161";
  11         model = "Netgear WNDR3800";
  12
  13         aliases {
  14                 led-status = &power_green;
  15         };
  16
  17         chosen {
  18                 bootargs = "console=ttyS0,115200";
  19         };
  20
  21         extosc: ref {
  22                 compatible = "fixed-clock";
  23                 #clock-cells = <0>;
  24                 clock-output-names = "ref";
  25                 clock-frequency = <40000000>;
  26         };
  27
  28         reset-leds {
  29                 compatible = "reset-leds";
  30
  31                 usb_led {
  32                         label = "netgear:green:usb";
  33                         resets = <&rst 12>;
  34                         trigger-sources = <&usb_ochi_port>, <&usb_echi_port>;
  35                         linux,default-trigger = "usbport";
  36                 };
  37         };
  38
  39         gpio-leds {
  40                 compatible = "gpio-leds";
  41
  42                 wps {
  43                         label = "netgear:orange:wps";
  44                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  45                         default-state = "off";
  46                 };
  47
  48                 power_green: power_green {
  49                         label = "netgear:green:power";
  50                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  51                         default-state = "off";
  52                 };
  53
  54                 power_orange {
  55                         label = "netgear:orange:power";
  56                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  57                         default-state = "off";
  58                 };
  59
  60                 wps_green {
  61                         label = "netgear:green:wps";
  62                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  63                         default-state = "off";
  64                 };
  65
  66                 wan_green {
  67                         label = "netgear:green:wan";
  68                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  69                         default-state = "off";
  70                 };
  71         };
  72
  73         gpio-keys-polled {
  74                 compatible = "gpio-keys-polled";
  75                 #address-cells = <1>;
  76                 #size-cells = <0>;
  77                 poll-interval = <100>;
  78
  79                 wps {
  80                         label = "wps";
  81                         linux,code = <KEY_WPS_BUTTON>;
  82                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  83                 };
  84
  85                 reset {
  86                         label = "reset";
  87                         linux,code = <KEY_RESTART>;
  88                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  89                 };
  90
  91                 rfkill {
  92                         label = "rfkill";
  93                         linux,code = <KEY_RFKILL>;
  94                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  95                 };
  96         };
  97
  98         rtl8366s {
  99                 compatible = "realtek,rtl8366s";
 100                 gpio-sda = <&gpio 5 GPIO_ACTIVE_HIGH>;
 101                 gpio-sck = <&gpio 7 GPIO_ACTIVE_HIGH>;
 102
 103                 mdio-bus {
 104                         status = "okay";
 105
 106                         phy-mask = <0x10>;
 107
 108                         phy4: ethernet-phy@4 {
 109                                 reg = <4>;
 110                                 phy-mode = "rgmii";
 111                         };
 112                 };
 113         };
 114 };
 115
 116 &usb_phy {
 117         status = "okay";
 118 };
 119
 120 &usb1 {
 121         status = "okay";
 122
 123         usb_ochi_port: port@1 {
 124                 reg = <1>;
 125                 #trigger-source-cells = <0>;
 126         };
 127 };
 128
 129 &usb2 {
 130         status = "okay";
 131
 132         usb_echi_port: port@1 {
 133                 reg = <1>;
 134                 #trigger-source-cells = <0>;
 135         };
 136 };
 137
 138 &pcie0 {
 139         status = "okay";
 140 };
 141
 142 &uart {
 143         status = "okay";
 144 };
 145
 146 &spi {
 147         status = "okay";
 148         num-cs = <1>;
 149
 150         flash@0 {
 151                 #address-cells = <1>;
 152                 #size-cells = <1>;
 153                 compatible = "jedec,spi-nor";
 154                 reg = <0>;
 155                 spi-max-frequency = <25000000>;
 156
 157                 partitions {
 158                         compatible = "fixed-partitions";
 159                         #address-cells = <1>;
 160                         #size-cells = <1>;
 161
 162                         partition@0 {
 163                                 label = "u-boot";
 164                                 reg = <0x000000 0x050000>;
 165                                 read-only;
 166                         };
 167
 168                         partition@1 {
 169                                 label = "u-boot-env";
 170                                 reg = <0x050000 0x020000>;
 171                                 read-only;
 172                         };
 173
 174                         partition@2 {
 175                                 label = "firmware";
 176                                 reg = <0x070000 0xf80000>;
 177                         };
 178
 179                         art: partition@3 {
 180                                 label = "art";
 181                                 reg = <0xff0000 0x010000>;
 182                                 read-only;
 183                         };
 184                 };
 185         };
 186 };
 187
 188 &eth0 {
 189         status = "okay";
 190
 191         pll-data = <0x11110000 0x00001099 0x00991099>;
 192
 193         mtd-mac-address = <&art 0x00>;
 194
 195         fixed-link {
 196                 speed = <1000>;
 197                 full-duplex;
 198         };
 199 };
 200
 201 &eth1 {
 202         status = "okay";
 203
 204         pll-data = <0x11110000 0x00001099 0x00991099>;
 205
 206         mtd-mac-address = <&art 0x06>;
 207
 208         resets = <&rst 13>;
 209         reset-names = "mac";
 210
 211         phy-handle = <&phy4>;
 212 };