target/linux/ath79/dts/ar9331_pisen_ts-d084.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9331.dtsi"
   8
   9 / {
  10         model = "Pisen TS-D084";
  11         compatible = "pisen,ts-d084", "qca,ar9331";
  12
  13         aliases {
  14                 serial0 = &uart;
  15                 led-boot = &led_system;
  16                 led-failsafe = &led_system;
  17                 led-running = &led_system;
  18                 led-upgrade = &led_system;
  19         };
  20
  21         keys {
  22                 compatible = "gpio-keys";
  23
  24                 reset {
  25                         label = "reset";
  26                         linux,code = <KEY_RESTART>;
  27                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  28                         debounce-interval = <60>;
  29                 };
  30         };
  31
  32         leds {
  33                 compatible = "gpio-leds";
  34
  35                 led_system: system {
  36                         label = "ts-d084:blue:system";
  37                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  38                 };
  39         };
  40 };
  41
  42 &spi {
  43         status = "okay";
  44
  45         flash@0 {
  46                 compatible = "jedec,spi-nor";
  47                 reg = <0>;
  48                 spi-max-frequency = <25000000>;
  49
  50                 partitions {
  51                         compatible = "fixed-partitions";
  52                         #address-cells = <1>;
  53                         #size-cells = <1>;
  54
  55                         uboot: partition@0 {
  56                                 reg = <0x0 0x20000>;
  57                                 label = "u-boot";
  58                                 read-only;
  59                         };
  60
  61                         firmware: partition@20000 {
  62                                 compatible = "tplink,firmware";
  63                                 reg = <0x20000 0x7d0000>;
  64                                 label = "firmware";
  65                         };
  66
  67                         art: partition@7f0000 {
  68                                 reg = <0x7f0000 0x10000>;
  69                                 label = "art";
  70                                 read-only;
  71                         };
  72                 };
  73         };
  74 };
  75
  76 &eth0 {
  77         status = "okay";
  78
  79         mtd-mac-address = <&uboot 0x1fc00>;
  80
  81         gmac-config {
  82                 device = <&gmac>;
  83
  84                 switch-phy-addr-swap = <0>;
  85                 switch-phy-swap = <0>;
  86         };
  87 };
  88
  89 &eth1 {
  90         status = "okay";
  91         compatible = "syscon", "simple-mfd";
  92 };
  93
  94 &gpio {
  95         status = "okay";
  96 };
  97
  98 &uart {
  99         status = "okay";
 100 };
 101
 102 &usb {
 103         dr_mode = "host";
 104         status = "okay";
 105 };
 106
 107 &usb_phy {
 108         status = "okay";
 109 };
 110
 111 &wmac {
 112         status = "okay";
 113         mtd-cal-data = <&art 0x1000>;
 114         mtd-mac-address = <&uboot 0x1fc00>;
 115 };