target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi

   1 /dts-v1/;
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca953x.dtsi"
   7
   8 / {
   9         aliases {
  10                 led-boot = &led_status;
  11                 led-failsafe = &led_status;
  12                 led-running = &led_status;
  13                 led-upgrade = &led_status;
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 pinctrl-names = "default";
  21                 pinctrl-0 = <&jtag_disable_pins>;
  22
  23                 button0 {
  24                         label = "reset";
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 button1 {
  30                         label = "button right";
  31                         linux,code = <BTN_0>;
  32                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  33                 };
  34
  35                 button3 {
  36                         label = "button left";
  37                         linux,code = <BTN_1>;
  38                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  39                 };
  40         };
  41
  42         leds {
  43                 compatible = "gpio-leds";
  44
  45                 // Colors from non-Lite versions
  46
  47                 led_status: status {
  48                         label = "gl-ar300m:green:status";
  49                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  50                 };
  51
  52                 led_lan: lan {
  53                         label = "gl-ar300m:green:lan";
  54                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  55                 };
  56
  57                 led_wlan: wlan {
  58                         label = "gl-ar300m:red:wlan";
  59                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  60                         linux,default-trigger = "phy0tpt";
  61                 };
  62         };
  63 };
  64
  65 &pcie0 {
  66         status = "okay";
  67 };
  68
  69 &spi {
  70         status = "okay";
  71         num-cs = <0>;
  72
  73         flash@0 {
  74                 compatible = "winbond,w25q128", "jedec,spi-nor";
  75                 reg = <0>;
  76                 spi-max-frequency = <25000000>;
  77
  78                 partitions {
  79                         compatible = "fixed-partitions";
  80                         #address-cells = <1>;
  81                         #size-cells = <1>;
  82
  83                         partition@0 {
  84                                 label = "u-boot";
  85                                 reg = <0x000000 0x040000>;
  86                                 read-only;
  87                         };
  88
  89                         partition@1 {
  90                                 label = "u-boot-env";
  91                                 reg = <0x040000 0x010000>;
  92                         };
  93
  94                         partition@2 {
  95                                 compatible = "denx,uimage";
  96                                 label = "firmware";
  97                                 reg = <0x050000 0xfa0000>;
  98                         };
  99
 100                         art: partition@3 {
 101                                 label = "art";
 102                                 reg = <0xff0000 0x010000>;
 103                                 read-only;
 104                         };
 105                 };
 106         };
 107 };
 108
 109 &uart {
 110         status = "okay";
 111 };
 112
 113 &usb0 {
 114         #address-cells = <1>;
 115         #size-cells = <0>;
 116         status = "okay";
 117 };
 118
 119 &usb_phy {
 120         status = "okay";
 121 };
 122
 123 &eth0 {
 124         status = "okay";
 125         mtd-mac-address = <&art 0x0>;
 126         phy-handle = <&swphy4>;
 127 };
 128
 129 &eth1 {
 130         mtd-mac-address = <&art 0x0>;
 131         mtd-mac-address-increment = <1>;
 132 };
 133
 134 &wmac {
 135         status = "okay";
 136         mtd-cal-data = <&art 0x1000>;
 137         mtd-mac-address = <&art 0x1002>;
 138 };