target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi

   1 /dts-v1/;
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca953x.dtsi"
   7
   8 / {
   9         aliases {
  10                 led-boot = &led_status;
  11                 led-failsafe = &led_status;
  12                 led-running = &led_status;
  13                 led-upgrade = &led_status;
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 pinctrl-names = "default";
  21                 pinctrl-0 = <&jtag_disable_pins>;
  22
  23                 reset {
  24                         label = "reset";
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 right {
  30                         label = "button right";
  31                         linux,code = <BTN_0>;
  32                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  33                 };
  34
  35                 left {
  36                         label = "button left";
  37                         linux,code = <BTN_1>;
  38                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  39                 };
  40         };
  41
  42         leds {
  43                 compatible = "gpio-leds";
  44
  45                 // Colors for non-Lite versions
  46
  47                 led_status: status {
  48                         label = "gl-ar300m:green:status";
  49                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  50                 };
  51
  52                 led_lan: lan {
  53                         label = "gl-ar300m:green:lan";
  54                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  55                 };
  56
  57                 led_wlan: wlan {
  58                         label = "gl-ar300m:red:wlan";
  59                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  60                         linux,default-trigger = "phy0tpt";
  61                 };
  62         };
  63
  64         i2c: i2c {
  65                 compatible = "i2c-gpio";
  66
  67                 sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  68                 scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  69         };
  70 };
  71
  72 &pcie0 {
  73         status = "okay";
  74 };
  75
  76 &spi {
  77         status = "okay";
  78
  79         num-cs = <2>;
  80         cs-gpios = <0>, <0>;
  81
  82         flash@0 {
  83                 compatible = "jedec,spi-nor";
  84                 reg = <0>;
  85                 spi-max-frequency = <25000000>;
  86
  87                 partitions {
  88                         compatible = "fixed-partitions";
  89                         #address-cells = <1>;
  90                         #size-cells = <1>;
  91
  92                         partition@0 {
  93                                 label = "u-boot";
  94                                 reg = <0x000000 0x040000>;
  95                                 read-only;
  96                         };
  97
  98                         partition@40000 {
  99                                 label = "u-boot-env";
 100                                 reg = <0x040000 0x010000>;
 101                         };
 102
 103                         nor_firmware: partition@50000 {
 104                                 label = "nor_firmware";
 105                                 reg = <0x050000 0xfa0000>;
 106                         };
 107
 108                         art: partition@ff0000 {
 109                                 label = "art";
 110                                 reg = <0xff0000 0x010000>;
 111                                 read-only;
 112                         };
 113                 };
 114         };
 115
 116         nand_flash: flash@1 {
 117                 compatible = "spi-nand";
 118                 reg = <1>;
 119                 spi-max-frequency = <25000000>;
 120
 121                 partitions {
 122                         compatible = "fixed-partitions";
 123                         #address-cells = <1>;
 124                         #size-cells = <1>;
 125
 126                         nand_kernel: partition@0 {
 127                                 label = "nand_kernel";
 128                                 reg = <0x000000 0x400000>;
 129                         };
 130
 131                         nand_ubi: partition@400000 {
 132                                 label = "nand_ubi";
 133                                 reg = <0x400000 0x7c00000>;
 134                         };
 135                 };
 136         };
 137 };
 138
 139 &uart {
 140         status = "okay";
 141 };
 142
 143 &usb0 {
 144         #address-cells = <1>;
 145         #size-cells = <0>;
 146         status = "okay";
 147 };
 148
 149 &usb_phy {
 150         status = "okay";
 151 };
 152
 153 &eth0 {
 154         status = "okay";
 155         mtd-mac-address = <&art 0x0>;
 156         phy-handle = <&swphy4>;
 157 };
 158
 159 &eth1 {
 160         mtd-mac-address = <&art 0x0>;
 161         mtd-mac-address-increment = <1>;
 162 };
 163
 164 &wmac {
 165         status = "okay";
 166         mtd-cal-data = <&art 0x1000>;
 167 };