target/linux/ath79/dts/qca9531_glinet_gl-ar300m.dtsi

   1 /dts-v1/;
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca953x.dtsi"
   7
   8 / {
   9         aliases {
  10                 led-boot = &led_status;
  11                 led-failsafe = &led_status;
  12                 led-running = &led_status;
  13                 led-upgrade = &led_status;
  14         };
  15
  16         keys {
  17                 compatible = "gpio-keys-polled";
  18                 poll-interval = <20>;
  19                 pinctrl-names = "default";
  20                 pinctrl-0 = <&jtag_disable_pins>;
  21
  22                 button0 {
  23                         label = "reset";
  24                         linux,code = <KEY_RESTART>;
  25                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  26                 };
  27
  28                 button1 {
  29                         label = "button right";
  30                         linux,code = <BTN_0>;
  31                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  32                 };
  33
  34                 button3 {
  35                         label = "button left";
  36                         linux,code = <BTN_1>;
  37                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  38                 };
  39         };
  40
  41         leds {
  42                 compatible = "gpio-leds";
  43
  44                 // Colors from non-Lite versions
  45
  46                 led_status: status {
  47                         label = "gl-ar300m:green:status";
  48                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  49                 };
  50
  51                 led_lan: lan {
  52                         label = "gl-ar300m:green:lan";
  53                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  54                 };
  55
  56                 led_wlan: wlan {
  57                         label = "gl-ar300m:red:wlan";
  58                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  59                         linux,default-trigger = "phy0tpt";
  60                 };
  61         };
  62 };
  63
  64 &pcie0 {
  65         status = "okay";
  66 };
  67
  68 &spi {
  69         status = "okay";
  70         num-cs = <0>;
  71
  72         flash@0 {
  73                 compatible = "winbond,w25q128", "jedec,spi-nor";
  74                 reg = <0>;
  75                 spi-max-frequency = <25000000>;
  76
  77                 partitions {
  78                         compatible = "fixed-partitions";
  79                         #address-cells = <1>;
  80                         #size-cells = <1>;
  81
  82                         partition@0 {
  83                                 label = "u-boot";
  84                                 reg = <0x000000 0x040000>;
  85                                 read-only;
  86                         };
  87
  88                         partition@1 {
  89                                 label = "u-boot-env";
  90                                 reg = <0x040000 0x010000>;
  91                         };
  92
  93                         partition@2 {
  94                                 compatible = "denx,uimage";
  95                                 label = "firmware";
  96                                 reg = <0x050000 0xfa0000>;
  97                         };
  98
  99                         art: partition@3 {
 100                                 label = "art";
 101                                 reg = <0xff0000 0x010000>;
 102                                 read-only;
 103                         };
 104                 };
 105         };
 106 };
 107
 108 &uart {
 109         status = "okay";
 110 };
 111
 112 &usb0 {
 113         #address-cells = <1>;
 114         #size-cells = <0>;
 115         status = "okay";
 116 };
 117
 118 &usb_phy {
 119         status = "okay";
 120 };
 121
 122 &eth0 {
 123         status = "okay";
 124         mtd-mac-address = <&art 0x0>;
 125         phy-handle = <&swphy4>;
 126 };
 127
 128 &eth1 {
 129         mtd-mac-address = <&art 0x0>;
 130         mtd-mac-address-increment = <1>;
 131 };
 132
 133 &wmac {
 134         status = "okay";
 135         mtd-cal-data = <&art 0x1000>;
 136         mtd-mac-address = <&art 0x1002>;
 137 };