target/linux/ath79/dts/qca9531_glinet_gl-ar750.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca953x.dtsi"
   8
   9 / {
  10         compatible = "glinet,gl-ar750", "qca,qca9531";
  11         model = "GL.iNet GL-AR750";
  12
  13         aliases {
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 pinctrl-names = "default";
  21                 pinctrl-0 = <&jtag_disable_pins>;
  22
  23                 reset {
  24                         label = "reset";
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  27                 };
  28
  29                 mode {
  30                         label = "mode";
  31                         linux,code = <BTN_0>;
  32                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  33                 };
  34         };
  35
  36         leds {
  37                 compatible = "gpio-leds";
  38
  39                 power {
  40                         label = "gl-ar750:white:power";
  41                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  42                         default-state = "on";
  43                 };
  44
  45                 wlan2g {
  46                         label = "gl-ar750:white:wlan2g";
  47                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  48                         linux,default-trigger = "phy1tpt";
  49                 };
  50
  51                 wlan5g {
  52                         label = "gl-ar750:white:wlan5g";
  53                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  54                         linux,default-trigger = "phy0tpt";
  55                 };
  56         };
  57
  58         i2c {
  59                 compatible = "i2c-gpio";
  60
  61                 sda-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  62                 scl-gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  63         };
  64 };
  65
  66 &pcie0 {
  67         status = "okay";
  68
  69         wifi@0,0 {
  70                 compatible = "qcom,ath10k";
  71                 reg = <0 0 0 0 0>;
  72                 device_type = "pci";
  73         };
  74 };
  75
  76 &uart {
  77         status = "okay";
  78 };
  79
  80 &usb0 {
  81         status = "okay";
  82 };
  83
  84 &usb_phy {
  85         status = "okay";
  86 };
  87
  88 &spi {
  89         status = "okay";
  90         num-cs = <0>;
  91
  92         flash@0 {
  93                 compatible = "jedec,spi-nor";
  94                 reg = <0>;
  95                 spi-max-frequency = <25000000>;
  96
  97                 partitions {
  98                         compatible = "fixed-partitions";
  99                         #address-cells = <1>;
 100                         #size-cells = <1>;
 101
 102                         partition@0 {
 103                                 label = "u-boot";
 104                                 reg = <0x000000 0x040000>;
 105                                 read-only;
 106                         };
 107
 108                         partition@40000 {
 109                                 label = "u-boot-env";
 110                                 reg = <0x040000 0x010000>;
 111                                 read-only;
 112                         };
 113
 114                         art: partition@50000 {
 115                                 label = "art";
 116                                 reg = <0x050000 0x010000>;
 117                                 read-only;
 118                         };
 119
 120                         partition@60000 {
 121                                 compatible = "denx,uimage";
 122                                 label = "firmware";
 123                                 reg = <0x060000 0xfa0000>;
 124                         };
 125                 };
 126         };
 127 };
 128
 129 &eth0 {
 130         status = "okay";
 131         mtd-mac-address = <&art 0x0>;
 132         phy-handle = <&swphy4>;
 133 };
 134
 135 &eth1 {
 136         mtd-mac-address = <&art 0x0>;
 137         mtd-mac-address-increment = <1>;
 138 };
 139
 140 &wmac {
 141         status = "okay";
 142         mtd-cal-data = <&art 0x1000>;
 143 };