target/linux/ath79/dts/qca9531_glinet_gl-x750.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca953x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "glinet,gl-x750", "qca,qca9531";
  10         model = "GL.iNet GL-X750";
  11
  12         keys {
  13                 compatible = "gpio-keys";
  14
  15                 pinctrl-names = "default";
  16                 pinctrl-0 = <&jtag_disable_pins>;
  17
  18                 reset {
  19                         label = "reset";
  20                         linux,code = <KEY_RESTART>;
  21                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  22                 };
  23         };
  24
  25         leds {
  26                 compatible = "gpio-leds";
  27
  28                 power {
  29                         label = "green:power";
  30                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  31                         default-state = "on";
  32                 };
  33
  34                 wlan2g {
  35                         label = "green:wlan2g";
  36                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  37                         linux,default-trigger = "phy1tpt";
  38                 };
  39
  40                 wlan5g {
  41                         label = "green:wlan5g";
  42                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  43                         linux,default-trigger = "phy0tpt";
  44                 };
  45
  46                 wan {
  47                         label = "green:wan";
  48                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  49                 };
  50
  51                 4g {
  52                         label = "green:4g";
  53                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  54                 };
  55         };
  56 };
  57
  58 &pcie0 {
  59         status = "okay";
  60 };
  61
  62 &uart {
  63         status = "okay";
  64 };
  65
  66 &usb0 {
  67         #address-cells = <1>;
  68         #size-cells = <0>;
  69         status = "okay";
  70
  71         hub_port: port@1 {
  72                 reg = <1>;
  73                 #trigger-source-cells = <0>;
  74         };
  75 };
  76
  77 &usb_phy {
  78         status = "okay";
  79 };
  80
  81 &spi {
  82         status = "okay";
  83
  84         flash@0 {
  85                 compatible = "jedec,spi-nor";
  86                 reg = <0>;
  87                 spi-max-frequency = <25000000>;
  88
  89                 partitions {
  90                         compatible = "fixed-partitions";
  91                         #address-cells = <1>;
  92                         #size-cells = <1>;
  93
  94                         partition@0 {
  95                                 label = "u-boot";
  96                                 reg = <0x000000 0x040000>;
  97                                 read-only;
  98                         };
  99
 100                         partition@40000 {
 101                                 label = "u-boot-env";
 102                                 reg = <0x040000 0x010000>;
 103                         };
 104
 105                         art: partition@50000 {
 106                                 label = "art";
 107                                 reg = <0x050000 0x010000>;
 108                                 read-only;
 109                         };
 110
 111                         partition@60000 {
 112                                 compatible = "denx,uimage";
 113                                 label = "firmware";
 114                                 reg = <0x060000 0xfa0000>;
 115                         };
 116                 };
 117         };
 118 };
 119
 120 &eth0 {
 121         status = "okay";
 122
 123         phy-handle = <&swphy4>;
 124
 125         mtd-mac-address = <&art 0x0>;
 126 };
 127
 128 &eth1 {
 129         mtd-mac-address = <&art 0x0>;
 130         mtd-mac-address-increment = <1>;
 131 };
 132
 133 &wmac {
 134         status = "okay";
 135
 136         mtd-cal-data = <&art 0x1000>;
 137 };