target/linux/ath79/dts/qca9558_ocedo_koala.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca955x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "ocedo,koala", "qca,qca9558";
  10         model = "OCEDO Koala";
  11
  12         aliases {
  13                 led-boot = &led_system;
  14                 led-failsafe = &led_system;
  15                 led-running = &led_system;
  16                 led-upgrade = &led_system;
  17                 label-mac-device = &eth0;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 power {
  24                         label = "green:power";
  25                         gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
  26                         default-state = "on";
  27                 };
  28
  29                 wifi2 {
  30                         label = "yellow:wlan2";
  31                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  32                         linux,default-trigger = "phy1tpt";
  33                 };
  34
  35                 wifi5 {
  36                         label = "red:wlan58";
  37                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  38                         linux,default-trigger = "phy0tpt";
  39                 };
  40
  41                 led_system: system {
  42                         label = "blue:sys";
  43                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  44                 };
  45         };
  46
  47         keys {
  48                 compatible = "gpio-keys";
  49
  50                 reset {
  51                         label = "reset";
  52                         linux,code = <KEY_RESTART>;
  53                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  54                 };
  55         };
  56 };
  57
  58 &pcie0 {
  59         status = "okay";
  60 };
  61
  62 &uart {
  63         status = "okay";
  64 };
  65
  66 &pll {
  67         clocks = <&extosc>;
  68 };
  69
  70 &spi {
  71         status = "okay";
  72
  73         flash@0 {
  74                 compatible = "jedec,spi-nor";
  75                 reg = <0>;
  76                 spi-max-frequency = <25000000>;
  77
  78                 partitions {
  79                         compatible = "fixed-partitions";
  80                         #address-cells = <1>;
  81                         #size-cells = <1>;
  82
  83                         uboot: partition@0 {
  84                                 label = "u-boot";
  85                                 reg = <0x000000 0x040000>;
  86                                 read-only;
  87                         };
  88
  89                         partition@40000 {
  90                                 label = "u-boot-env";
  91                                 reg = <0x040000 0x010000>;
  92                         };
  93
  94                         partition@50000 {
  95                                 compatible = "denx,uimage";
  96                                 label = "firmware";
  97                                 reg = <0x050000 0x740000>;
  98                         };
  99
 100                         partition@790000 {
 101                                 label = "vendor";
 102                                 reg = <0x790000 0x740000>;
 103                                 read-only;
 104                         };
 105
 106                         partition@ed0000 {
 107                                 label = "data";
 108                                 reg = <0xed0000 0x110000>;
 109                                 read-only;
 110                         };
 111
 112                         partition@fe0000 {
 113                                 label = "id";
 114                                 reg = <0xfe0000 0x010000>;
 115                                 read-only;
 116                         };
 117
 118                         art: partition@ff0000 {
 119                                 label = "art";
 120                                 reg = <0xff0000 0x010000>;
 121                                 read-only;
 122                         };
 123                 };
 124         };
 125 };
 126
 127 &wmac {
 128         status = "okay";
 129
 130         mtd-cal-data = <&art 0x1000>;
 131         mtd-mac-address = <&art 0x06>;
 132 };
 133
 134 &mdio0 {
 135         status = "okay";
 136
 137         phy5: ethernet-phy@5 {
 138                 reg = <5>;
 139                 eee-broken-100tx;
 140                 eee-broken-1000t;
 141         };
 142 };
 143
 144 &eth0 {
 145         status = "okay";
 146
 147         mtd-mac-address = <&art 0x00>;
 148
 149         phy-handle = <&phy5>;
 150         phy-mode = "rgmii-rxid";
 151
 152         pll-data = <0x8e000000 0x80000101 0x80001313>;
 153 };