target/linux/ath79/dts/qca9558_ocedo_ursus.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca9557.dtsi"
   8
   9 / {
  10         compatible = "ocedo,ursus", "qca,qca9558";
  11         model = "OCEDO Ursus";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         leds {
  18                 compatible = "gpio-leds";
  19
  20                 wifi2 {
  21                         label = "ursus:green:wlan2g";
  22                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  23                         linux,default-trigger = "phy1tpt";
  24                 };
  25
  26                 wifi5 {
  27                         label = "ursus:green:wlan5g";
  28                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  29                         linux,default-trigger = "phy0tpt";
  30                 };
  31         };
  32 };
  33
  34 &pcie1 {
  35         status = "okay";
  36 };
  37
  38 &uart {
  39         status = "okay";
  40 };
  41
  42 &pll {
  43         clocks = <&extosc>;
  44 };
  45
  46 &spi {
  47         status = "okay";
  48         num-cs = <1>;
  49
  50         flash@0 {
  51                 compatible = "jedec,spi-nor";
  52                 reg = <0>;
  53                 spi-max-frequency = <25000000>;
  54
  55                 partitions {
  56                         compatible = "fixed-partitions";
  57                         #address-cells = <1>;
  58                         #size-cells = <1>;
  59
  60                         uboot: partition@0 {
  61                                 label = "u-boot";
  62                                 reg = <0x000000 0x040000>;
  63                                 read-only;
  64                         };
  65
  66                         partition@40000 {
  67                                 label = "u-boot-env";
  68                                 reg = <0x040000 0x010000>;
  69                         };
  70
  71                         partition@50000 {
  72                                 compatible = "denx,uimage";
  73                                 label = "firmware";
  74                                 reg = <0x050000 0x740000>;
  75                         };
  76
  77                         partition@790000 {
  78                                 label = "vendor";
  79                                 reg = <0x790000 0x740000>;
  80                                 read-only;
  81                         };
  82
  83                         partition@ed0000 {
  84                                 label = "data";
  85                                 reg = <0xed0000 0x110000>;
  86                                 read-only;
  87                         };
  88
  89                         partition@fe0000 {
  90                                 label = "id";
  91                                 reg = <0xfe0000 0x010000>;
  92                                 read-only;
  93                         };
  94
  95                         art: partition@ff0000 {
  96                                 label = "art";
  97                                 reg = <0xff0000 0x010000>;
  98                                 read-only;
  99                         };
 100                 };
 101         };
 102 };
 103
 104 &wmac {
 105         status = "okay";
 106
 107         mtd-cal-data = <&art 0x1000>;
 108         mtd-mac-address = <&art 0x06>;
 109 };
 110
 111 &mdio0 {
 112         status = "okay";
 113
 114         phy1: ethernet-phy@1 {
 115                 reg = <1>;
 116         };
 117
 118         phy2: ethernet-phy@2 {
 119                 reg = <2>;
 120         };
 121 };
 122
 123 &eth0 {
 124         status = "okay";
 125         mtd-mac-address = <&art 0x00>;
 126
 127         phy-mode = "rgmii-rxid";
 128         phy-handle = <&phy1>;
 129         pll-data = <0x8e000000 0x80000101 0x80001313>;
 130
 131         gmac_config: gmac-config {
 132                 device = <&gmac>;
 133
 134                 rxdv-delay = <3>;
 135                 rxd-delay = <3>;
 136                 txen-delay = <0>;
 137                 txd-delay = <0>;
 138                 rgmii-enabled = <1>;
 139         };
 140 };
 141
 142 &eth1 {
 143         status = "okay";
 144         mtd-mac-address = <&art 0x12>;
 145         phy-handle = <&phy2>;
 146         pll-data = <0x3000101 0x101 0x1313>;
 147 };