target/linux/ath79/dts/qca9563_glinet_gl-ar750s.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 /dts-v1/;
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 #include "qca956x.dtsi"
   9
  10 / {
  11         compatible = "glinet,gl-ar750s", "qca,qca9563";
  12         model = "GL.iNet GL-AR750S";
  13
  14         chosen {
  15                 bootargs = "console=ttyS0,115200n8";
  16         };
  17
  18         aliases {
  19                 led-boot = &led_power;
  20                 led-failsafe = &led_power;
  21                 led-running = &led_power;
  22                 led-upgrade = &led_power;
  23                 label-mac-device = &eth0;
  24         };
  25
  26         keys {
  27                 compatible = "gpio-keys";
  28
  29                 pinctrl-names = "default";
  30                 pinctrl-0 = <&jtag_disable_pins>;
  31
  32                 reset {
  33                         label = "reset";
  34                         linux,code = <KEY_RESTART>;
  35                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  36                 };
  37
  38                 mode {
  39                         label = "mode";
  40                         linux,code = <BTN_0>;
  41                         linux,input-type = <EV_SW>;
  42                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  43                 };
  44         };
  45
  46         leds {
  47                 compatible = "gpio-leds";
  48
  49                 led_power: power {
  50                         label = "gl-ar750s:green:power";
  51                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  52                         default-state = "keep";
  53                 };
  54
  55                 led_wlan2g: wlan2g {
  56                         label = "gl-ar750s:green:wlan2g";
  57                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  58                         linux,default-trigger = "phy1tpt";
  59                 };
  60
  61                 led_wlan5g: wlan5g {
  62                         label = "gl-ar750s:green:wlan5g";
  63                         gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
  64                         linux,default-trigger = "phy0tpt";
  65                 };
  66         };
  67
  68         i2c: i2c {
  69                 compatible = "i2c-gpio";
  70
  71                 sda-gpios = <&gpio  5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  72                 scl-gpios = <&gpio 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  73         };
  74 };
  75
  76 &spi {
  77         status = "okay";
  78
  79         num-cs = <2>;
  80         cs-gpios = <0>, <0>;
  81
  82         flash_nor: flash@0 {
  83                 compatible = "jedec,spi-nor";
  84                 reg = <0>;
  85                 spi-max-frequency = <25000000>;
  86
  87                 nor_partitions: partitions {
  88                         compatible = "fixed-partitions";
  89                         #address-cells = <1>;
  90                         #size-cells = <1>;
  91
  92                         partition@0 {
  93                                 label = "u-boot";
  94                                 reg = <0x000000 0x040000>;
  95                                 read-only;
  96                         };
  97
  98                         partition@40000 {
  99                                 label = "u-boot-env";
 100                                 reg = <0x040000 0x010000>;
 101                         };
 102
 103                         art: partition@50000 {
 104                                 label = "art";
 105                                 reg = <0x050000 0x010000>;
 106                                 read-only;
 107                         };
 108
 109                         nor_firmware: partition@60000 {
 110                                 label = "nor_firmware";
 111                                 reg = <0x060000 0xfa0000>;
 112                         };
 113
 114                         nor_kernel: partition_alt@60000 {
 115                                 label = "nor_kernel";
 116                                 reg = <0x060000 0x400000>;
 117                         };
 118
 119                         nor_reserved: parition_alt@460000 {
 120                                 label = "nor_reserved";
 121                                 reg = <0x460000 0xba0000>;
 122                         };
 123                 };
 124         };
 125
 126         flash_nand: flash@1 {
 127                 compatible = "spi-nand";
 128                 reg = <1>;
 129                 spi-max-frequency = <25000000>;
 130
 131                 nand_partitions: partitions {
 132                         compatible = "fixed-partitions";
 133                         #address-cells = <1>;
 134                         #size-cells = <1>;
 135
 136                         nand_ubi: partition@0 {
 137                                 label = "nand_ubi";
 138                                 reg = <0x000000 0x8000000>;
 139                         };
 140                 };
 141         };
 142 };
 143
 144 &eth0 {
 145         status = "okay";
 146
 147         phy-handle = <&phy0>;
 148         mtd-mac-address = <&art 0x0>;
 149 };
 150
 151 &gpio {
 152         usb_vbus {
 153                 gpio-hog;
 154                 gpios = <7 GPIO_ACTIVE_HIGH>;
 155                 output-high;
 156                 line-name = "usb-vbus";
 157         };
 158 };
 159
 160 &mdio0 {
 161         status = "okay";
 162
 163         phy-mask = <0>;
 164
 165         phy0: ethernet-phy@0 {
 166                 reg = <0>;
 167                 phy-mode = "sgmii";
 168                 qca,ar8327-initvals = <
 169                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 170                         0x7c 0x0000007e /* PORT0_STATUS */
 171                 >;
 172         };
 173 };
 174
 175 &pcie {
 176         status = "okay";
 177 };
 178
 179 &uart {
 180         status = "okay";
 181 };
 182
 183 &usb0 {
 184         status = "okay";
 185 };
 186
 187 &usb1 {
 188         status = "okay";
 189 };
 190
 191 &usb_phy0 {
 192         status = "okay";
 193 };
 194
 195 &usb_phy1 {
 196         status = "okay";
 197 };
 198
 199 &wmac {
 200         status = "okay";
 201
 202         mtd-cal-data = <&art 0x1000>;
 203 };