5 #include <dt-bindings/input/input.h>
8 model = "BTHOMEHUBV5A - BT Home Hub 5A";
11 bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
15 led-boot = &power_green;
16 led-failsafe = &power_red;
17 led-running = &power_blue;
19 led-internet = &broadband_blue;
20 led-wifi = &wireless_blue;
24 reg = <0x0 0x8000000>;
30 compatible = "gen_nand", "lantiq,nand-xway";
33 reg = <0x1 0x0 0x2000000>;
38 compatible = "fixed-partitions";
49 reg = <0x40000 0x40000>;
51 caldata: partition@80000 {
53 reg = <0x80000 0x20000>;
58 reg = <0xa0000 0x200000>;
62 reg = <0x2a0000 0x7d60000>;
68 gpio: pinmux@E100B10 {
69 pinctrl-names = "default";
70 pinctrl-0 = <&state_default>;
72 state_default: pinmux {
74 lantiq,groups = "mdio";
75 lantiq,function = "mdio";
91 lantiq,open-drain = <0>;
95 lantiq,groups = "nand cle", "nand ale";
96 lantiq,function = "ebu";
98 lantiq,open-drain = <0>;
102 lantiq,groups = "nand cs1";
103 lantiq,function = "ebu";
104 lantiq,open-drain = <0>;
112 gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
117 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
122 compatible = "lantiq,phy-xrx200";
123 firmware1 = "lantiq/vr9_phy11g_a1x.bin"; /*VR9 1.1*/
124 firmware2 = "lantiq/vr9_phy11g_a2x.bin"; /*VR9 1.2*/
129 compatible = "ath9k,eeprom";
130 ath,eep-flash = <&caldata 0x1000>;
131 ath,mac-offset = <0x110c>;
132 ath,mac-increment = <2>;
133 ath,pci-slot = <0xe>; /* 14 */
137 compatible = "gpio-keys-polled";
138 #address-cells = <1>;
140 poll-interval = <100>;
144 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
145 linux,code = <KEY_RESTART>;
150 gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
151 linux,code = <KEY_WPS_BUTTON>;
156 gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
157 linux,code = <KEY_POWER>;
162 compatible = "gpio-leds";
164 /* broadband-* is a single RGB led */
166 label = "bthomehubv5a:red:broadband";
167 gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
170 label = "bthomehubv5a:green:broadband";
171 gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
173 broadband_blue: broadband-blue {
174 label = "bthomehubv5a:blue:broadband";
175 gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
178 /* wireless-* is a single RGB led */
180 label = "bthomehubv5a:red:wireless";
181 gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
184 label = "bthomehubv5a:green:wireless";
185 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
187 wireless_blue: wireless-blue {
188 label = "bthomehubv5a:blue:wireless";
189 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
192 /* power-* is a single RGB led */
193 power_red: power-red {
194 label = "bthomehubv5a:red:power";
195 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
197 power_green: power-green {
198 label = "bthomehubv5a:green:power";
199 gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
200 default-state = "keep";
202 power_blue: power-blue {
203 label = "bthomehubv5a:blue:power";
204 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
209 gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
216 compatible = "lantiq,xrx200-pdi";
217 #address-cells = <1>;
220 mtd-mac-address = <&caldata 0x110c>;
224 compatible = "lantiq,xrx200-pdi-port";
227 phy-handle = <&phy0>;
230 compatible = "lantiq,xrx200-pdi-port";
233 phy-handle = <&phy1>;
236 compatible = "lantiq,xrx200-pdi-port";
239 phy-handle = <&phy11>;
242 compatible = "lantiq,xrx200-pdi-port";
245 phy-handle = <&phy13>;
250 compatible = "lantiq,xrx200-pdi";
251 #address-cells = <1>;
254 mtd-mac-address = <&caldata 0x110c>;
255 mtd-mac-address-increment = <4>;
259 compatible = "lantiq,xrx200-pdi-port";
262 phy-handle = <&phy5>;
267 #address-cells = <1>;
269 compatible = "lantiq,xrx200-mdio";
271 phy0: ethernet-phy@0 {
273 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
275 phy1: ethernet-phy@1 {
277 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
279 phy5: ethernet-phy@5 {
281 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
283 phy11: ethernet-phy@11 {
285 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
287 phy13: ethernet-phy@13 {
289 compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";