target/linux/ramips/dts/WLI-TX4-AG300N.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         #address-cells = <1>;
  10         #size-cells = <1>;
  11         compatible = "buffalo,wli-tx4-ag300n", "ralink,rt2880-soc";
  12         model = "Buffalo WLI-TX4-AG300N";
  13
  14         aliases {
  15                 led-status = &led_power;
  16         };
  17
  18         cfi@1f000000 {
  19                 compatible = "cfi-flash";
  20                 reg = <0x1f000000 0x800000>;
  21                 bank-width = <2>;
  22                 device-width = <2>;
  23
  24                 partitions {
  25                         compatible = "fixed-partitions";
  26                         #address-cells = <1>;
  27                         #size-cells = <1>;
  28
  29                         partition@0 {
  30                                 label = "uboot";
  31                                 reg = <0x0 0x30000>;
  32                                 read-only;
  33                         };
  34
  35                         partition@30000 {
  36                                 label = "uboot-env";
  37                                 reg = <0x30000 0x10000>;
  38                                 read-only;
  39                         };
  40
  41                         factory: partition@40000 {
  42                                 label = "factory";
  43                                 reg = <0x40000 0x10000>;
  44                                 read-only;
  45                         };
  46
  47                         partition@50000 {
  48                                 label = "firmware";
  49                                 reg = <0x50000 0x3b0000>;
  50                         };
  51                 };
  52         };
  53
  54         gpio-keys-polled {
  55                 compatible = "gpio-keys-polled";
  56                 poll-interval = <100>;
  57
  58                 wps {
  59                         label = "wps";
  60                         gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
  61                         linux,code = <KEY_WPS_BUTTON>;
  62                 };
  63
  64                 bandwidth {
  65                         label = "bandwidth";
  66                         gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
  67                         linux,code = <KEY_RESTART>;
  68                 };
  69
  70                 reset {
  71                         label = "reset";
  72                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  73                         linux,code = <KEY_RESTART>;
  74                 };
  75         };
  76
  77         gpio-leds {
  78                 compatible = "gpio-leds";
  79
  80                 diag {
  81                         label = "wli-tx4-ag300n:red:diag";
  82                         gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
  83                 };
  84
  85                 led_power: power {
  86                         label = "wli-tx4-ag300n:blue:power";
  87                         gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
  88                 };
  89
  90                 security {
  91                         label = "wli-tx4-ag300n:blue:security";
  92                         gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
  93                 };
  94         };
  95 };
  96
  97 &gpio0 {
  98         status = "okay";
  99 };
 100
 101 &ethernet {
 102         status = "okay";
 103         mtd-mac-address = <&factory 0x4>;
 104
 105         port@0 {
 106                 mediatek,fixed-link = <100 1 1 1>;
 107         };
 108
 109         mdio-bus {
 110                 status = "okay";
 111
 112                 phy0: ethernet-phy@0 {
 113                         phy-mode = "mii";
 114                         reg = <0>;
 115                 };
 116         };
 117 };
 118
 119 &wmac {
 120         ralink,mtd-eeprom = <&factory 0>;
 121 };