target/linux/ramips/dts/WNCE2001.dts

   1 /dts-v1/;
   2
   3 #include "rt3050.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         compatible = "netgear,wnce2001", "ralink,rt3052-soc";
  10         model = "Netgear WNCE2001";
  11
  12         aliases {
  13                 led-status = &led_power_green;
  14         };
  15
  16         chosen {
  17                 bootargs = "console=ttyS0,115200";
  18         };
  19
  20         gpio-leds {
  21                 compatible = "gpio-leds";
  22
  23                 led_power_green: power-green {
  24                         label = "wnce2001:green:power";
  25                         gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
  26                 };
  27
  28                 power-red {
  29                         label = "wnce2001:red:power";
  30                         gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
  31                 };
  32
  33                 wlan-green {
  34                         label = "wnce2001:green:wlan";
  35                         gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
  36                 };
  37
  38                 wlan-red {
  39                         label = "wnce2001:red:wlan";
  40                         gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
  41                 };
  42         };
  43
  44         gpio-keys-polled {
  45                 compatible = "gpio-keys-polled";
  46                 poll-interval = <20>;
  47
  48                 reset {
  49                         label = "reset";
  50                         gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
  51                         linux,code = <KEY_RESTART>;
  52                 };
  53
  54                 wps {
  55                         label = "wps";
  56                         gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
  57                         linux,code = <KEY_WPS_BUTTON>;
  58                 };
  59
  60                 rt {
  61                         label = "rt";
  62                         gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
  63                         linux,code = <BTN_0>;
  64                 };
  65
  66                 ap {
  67                         label = "ap";
  68                         gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
  69                         linux,code = <BTN_1>;
  70                 };
  71         };
  72 };
  73
  74 &spi0 {
  75         status = "okay";
  76
  77         m25p80@0 {
  78                 #address-cells = <1>;
  79                 #size-cells = <1>;
  80                 compatible = "jedec,spi-nor";
  81                 reg = <0>;
  82                 spi-max-frequency = <10000000>;
  83
  84                 partition@0 {
  85                         label = "u-boot";
  86                         reg = <0x0 0x30000>;
  87                         read-only;
  88                 };
  89
  90                 factory: partition@30000 {
  91                         label = "factory";
  92                         reg = <0x30000 0x10000>;
  93                         read-only;
  94                 };
  95
  96                 partition@40000 {
  97                         label = "config";
  98                         reg = <0x40000 0x20000>;
  99                         read-only;
 100                 };
 101
 102                 partition@60000 {
 103                         label = "language";
 104                         reg = <0x60000 0x30000>;
 105                         read-only;
 106                 };
 107
 108                 partition@90000 {
 109                         label = "pot";
 110                         reg = <0x90000 0x10000>;
 111                         read-only;
 112                 };
 113
 114                 partition@a0000 {
 115                         label = "checksum";
 116                         reg = <0xa0000 0x10000>;
 117                 };
 118
 119                 partition@b0000 {
 120                         label = "firmware";
 121                         reg = <0xb0000 0x350000>;
 122                 };
 123         };
 124 };
 125
 126 &pinctrl {
 127         state_default: pinctrl0 {
 128                 gpio {
 129                         ralink,group = "i2c", "jtag", "rgmii", "mdio", "uartf";
 130                         ralink,function = "gpio";
 131                 };
 132         };
 133 };
 134
 135 &ethernet {
 136         mtd-mac-address = <&factory 0x28>;
 137 };
 138
 139 &wmac {
 140         ralink,mtd-eeprom = <&factory 0>;
 141 };