ar71xx: Add support for TP-Link CPE210 v2
authorAdrian Schmutzler <freifunk@adrianschmutzler.de>
Fri, 19 Jan 2018 13:45:42 +0000 (14:45 +0100)
committerMatthias Schiffer <mschiffer@universe-factory.net>
Sat, 23 Jun 2018 14:08:22 +0000 (16:08 +0200)
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 5c5bf8b8658a588423f6ec445d7ef6a36f99a396)

target/linux/ar71xx/base-files/etc/board.d/01_leds
target/linux/ar71xx/base-files/etc/board.d/02_network
target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
target/linux/ar71xx/files/arch/mips/ath79/mach-cpe510.c
target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
target/linux/ar71xx/image/generic-tp-link.mk
tools/firmware-utils/src/tplink-safeloader.c

index 2de8472e27b99c1dd280b88acff4357baee40227..3bc98bd99ff166d646662bb9a2c5894650cb47c5 100755 (executable)
@@ -235,16 +235,25 @@ cf-e530n)
        ucidef_set_led_netdev "wan" "WAN" "$board:blue:wan" "eth1"
        ;;
 cpe210|\
+cpe210-v2|\
 cpe510|\
 wbs210|\
 wbs510)
-       ucidef_set_led_switch "lan0" "LAN0" "tp-link:green:lan0" "switch0" "0x20"
-       ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
        ucidef_set_rssimon "wlan0" "200000" "1"
        ucidef_set_led_rssi "rssilow" "RSSILOW" "tp-link:green:link1" "wlan0" "1" "100" "0" "13"
        ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "tp-link:green:link2" "wlan0" "26" "100" "-25" "13"
        ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "51" "100" "-50" "13"
        ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "76" "100" "-75" "13"
+
+       case "$board" in
+       cpe210-v2)
+               ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan0" "eth0"
+               ;;
+       *)
+               ucidef_set_led_switch "lan0" "LAN0" "tp-link:green:lan0" "switch0" "0x20"
+               ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
+               ;;
+       esac
        ;;
 cr3000)
        ucidef_set_led_netdev "wan" "WAN" "pcs:blue:wan" "eth1"
index 450712644e7a595aa3497d3bbc944c5a3599b1fb..a5e58273621d1a22c0295fffc7e00e0a72875863 100755 (executable)
@@ -74,6 +74,7 @@ ar71xx_setup_interfaces()
        cap4200ag|\
        cf-e380ac-v1|\
        cf-e380ac-v2|\
+       cpe210-v2|\
        dr342|\
        eap120|\
        eap300v2|\
index bf9d87b3b99bc79202ac0bb91d53eb919c17ec8f..b713629da332ad3ed1d235ecc78ad1c7ddb7b209 100644 (file)
@@ -1573,6 +1573,7 @@ config ATH79_MACH_CPE505N
 config ATH79_MACH_CPE510
        bool "TP-LINK CPE510 support"
        select SOC_AR934X
+       select SOC_QCA953X
        select ATH79_DEV_ETH
        select ATH79_DEV_GPIO_BUTTONS
        select ATH79_DEV_LEDS_GPIO
index d2dbed1fe286c44d3188262e984253faaee7edba..ceb1769ddd522d51014228fe65e2662f2f3e627c 100644 (file)
@@ -1,7 +1,8 @@
 /*
- *  TP-LINK CPE210/220/510/520 board support
+ *  TP-LINK CPE210/210 v2/220/510/520 board support
  *
  *  Copyright (C) 2014 Matthias Schiffer <mschiffer@universe-factory.net>
+ *  Copyright (C) 2017 Robert Marko <robimarko@gmail.com>
  *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
@@ -41,6 +42,8 @@
 #define CPE510_KEYS_POLL_INTERVAL      20 /* msecs */
 #define CPE510_KEYS_DEBOUNCE_INTERVAL  (3 * CPE510_KEYS_POLL_INTERVAL)
 
+/* CPE210 v2 reset GPIO */
+#define CPE210_V2_GPIO_BTN_RESET       17
 
 static struct gpio_led cpe510_leds_gpio[] __initdata = {
        {
@@ -98,6 +101,30 @@ static struct gpio_led wbs510_leds_gpio[] __initdata = {
        },
 };
 
+static struct gpio_led cpe210_v2_leds_gpio[] __initdata = {
+       {
+               .name           = "tp-link:green:lan0",
+               .gpio           = CPE510_GPIO_LED_LAN0,
+               .active_low     = 1,
+       }, {
+               .name           = "tp-link:green:link1",
+               .gpio           = CPE510_GPIO_LED_L1,
+               .active_low     = 1,
+       }, {
+               .name           = "tp-link:green:link2",
+               .gpio           = CPE510_GPIO_LED_L2,
+               .active_low     = 1,
+       }, {
+               .name           = "tp-link:green:link3",
+               .gpio           = CPE510_GPIO_LED_L3,
+               .active_low     = 1,
+       }, {
+               .name           = "tp-link:green:link4",
+               .gpio           = CPE510_GPIO_LED_L4,
+               .active_low     = 1,
+       },
+};
+
 static struct gpio_keys_button cpe510_gpio_keys[] __initdata = {
        {
                .desc           = "Reset button",
@@ -109,6 +136,17 @@ static struct gpio_keys_button cpe510_gpio_keys[] __initdata = {
        }
 };
 
+static struct gpio_keys_button cpe210_v2_gpio_keys[] __initdata = {
+       {
+               .desc           = "Reset button",
+               .type           = EV_KEY,
+               .code           = KEY_RESTART,
+               .debounce_interval = CPE510_KEYS_DEBOUNCE_INTERVAL,
+               .gpio           = CPE210_V2_GPIO_BTN_RESET,
+               .active_low     = 1,
+       }
+};
+
 static void __init cpe_setup(u8 *mac)
 {
        /* Disable JTAG, enabling GPIOs 0-3 */
@@ -171,9 +209,33 @@ static void __init wbs_setup(void)
        ath79_register_wmac(ee, mac);
 }
 
+static void __init cpe210_v2_setup(void)
+{
+       u8 *mac = (u8 *) KSEG1ADDR(0x1f830008);
+       u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000);
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(cpe210_v2_leds_gpio),
+                                cpe210_v2_leds_gpio);
+       ath79_register_gpio_keys_polled(-1, CPE510_KEYS_POLL_INTERVAL,
+                                       ARRAY_SIZE(cpe210_v2_gpio_keys),
+                                       cpe210_v2_gpio_keys);
+       ath79_register_m25p80(NULL);
+       ath79_register_mdio(0, 0x0);
+       ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+       ath79_eth0_data.duplex = DUPLEX_FULL;
+       ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+       ath79_eth0_data.speed = SPEED_100;
+       ath79_eth0_data.phy_mask = BIT(4);
+       ath79_register_eth(0);
+       ath79_register_wmac(ee, mac);
+}
+
 MIPS_MACHINE(ATH79_MACH_CPE210, "CPE210", "TP-LINK CPE210/220",
             cpe210_setup);
 
+MIPS_MACHINE(ATH79_MACH_CPE210_V2, "CPE210V2", "TP-LINK CPE210 v2",
+            cpe210_v2_setup);
+
 MIPS_MACHINE(ATH79_MACH_CPE510, "CPE510", "TP-LINK CPE510/520",
             cpe510_setup);
 
index 890ceab185732188c3101df68ff41b78c215b2af..008e9d8d8597f0d34c2436ebb4fb5c50f542d198 100644 (file)
@@ -73,7 +73,8 @@ enum ath79_mach_type {
        ATH79_MACH_CF_E385AC,                   /* COMFAST CF-E385AC */
        ATH79_MACH_CF_E520N,                    /* COMFAST CF-E520N */
        ATH79_MACH_CF_E530N,                    /* COMFAST CF-E530N */
-       ATH79_MACH_CPE210,                      /* TP-LINK CPE210 */
+       ATH79_MACH_CPE210,                      /* TP-LINK CPE210 v1 */
+       ATH79_MACH_CPE210_V2,                   /* TP-LINK CPE210 v2 */
        ATH79_MACH_CPE505N,                     /* P&W CPE505N */
        ATH79_MACH_CPE510,                      /* TP-LINK CPE510 */
        ATH79_MACH_CPE830,                      /* YunCore CPE830 */
index 6f7d608b01ed3a6ebf90a0fa1754cbed3f2cadff..502c88b1bae970e0242ce6fb934911b38f4e2c7a 100644 (file)
@@ -152,22 +152,26 @@ define Device/archer-c7-v5
 endef
 TARGET_DEVICES += archer-c7-v5
 
-define Device/cpe510-520-v1
-  DEVICE_TITLE := TP-LINK CPE510/520 v1
+define Device/cpexxx
   DEVICE_PACKAGES := rssileds
   MTDPARTS := spi0.0:128k(u-boot)ro,64k(partition-table)ro,64k(product-info)ro,1792k(kernel),5888k(rootfs),192k(config)ro,64k(ART)ro,7680k@0x40000(firmware)
   IMAGE_SIZE := 7680k
-  BOARDNAME := CPE510
-  TPLINK_BOARD_ID := CPE510
   DEVICE_PROFILE := CPE510
   LOADER_TYPE := elf
+  IMAGES := sysupgrade.bin factory.bin
+  IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade
+  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
+endef
+
+define Device/cpe510-520-v1
+  $(Device/cpexxx)
+  DEVICE_TITLE := TP-LINK CPE510/520 v1
+  BOARDNAME := CPE510
+  TPLINK_BOARD_ID := CPE510
   LOADER_FLASH_OFFS := 0x43000
   COMPILE := loader-$(1).elf
   COMPILE/loader-$(1).elf := loader-okli-compile
   KERNEL := kernel-bin | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 12288
-  IMAGES := sysupgrade.bin factory.bin
-  IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade
-  IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
 endef
 TARGET_DEVICES += cpe510-520-v1
 
@@ -179,6 +183,18 @@ define Device/cpe210-220-v1
 endef
 TARGET_DEVICES += cpe210-220-v1
 
+define Device/cpe210-v2
+  $(Device/cpexxx)
+  DEVICE_TITLE := TP-LINK CPE210 v2
+  BOARDNAME := CPE210V2
+  TPLINK_BOARD_ID := CPE210V2
+  KERNEL := kernel-bin | patch-cmdline | lzma | tplink-v1-header
+  TPLINK_HWID := 0x0
+  TPLINK_HWREV := 0
+  TPLINK_HEADER_VERSION := 1
+endef
+TARGET_DEVICES += cpe210-v2
+
 define Device/wbs210-v1
   $(Device/cpe510-520-v1)
   DEVICE_TITLE := TP-LINK WBS210 v1
index bdefb24e0c21644ccdd222bf84d423968625877d..b2cc96bc3ce765df62bee837bdf0e3cf2d53be1b 100644 (file)
@@ -155,6 +155,48 @@ static struct device_info boards[] = {
                .last_sysupgrade_partition = "support-list",
        },
 
+       /** Firmware layout for the CPE210 V2 */
+       {
+               .id     = "CPE210V2",
+               .vendor = "CPE210(TP-LINK|UN|N300-2|00000000):2.0\r\n",
+               .support_list =
+                       "SupportList:\r\n"
+                       "CPE210(TP-LINK|EU|N300-2|00000000):2.0\r\n"
+                       "CPE210(TP-LINK|EU|N300-2|45550000):2.0\r\n"
+                       "CPE210(TP-LINK|EU|N300-2|55530000):2.0\r\n"
+                       "CPE210(TP-LINK|UN|N300-2|00000000):2.0\r\n"
+                       "CPE210(TP-LINK|UN|N300-2|45550000):2.0\r\n"
+                       "CPE210(TP-LINK|UN|N300-2|55530000):2.0\r\n"
+                       "CPE210(TP-LINK|US|N300-2|55530000):2.0\r\n"
+                       "CPE210(TP-LINK|UN|N300-2):2.0\r\n"
+                       "CPE210(TP-LINK|EU|N300-2):2.0\r\n"
+                       "CPE210(TP-LINK|US|N300-2):2.0\r\n",
+               .support_trail = '\xff',
+               .soft_ver = NULL,
+
+               .partitions = {
+                       {"fs-uboot", 0x00000, 0x20000},
+                       {"partition-table", 0x20000, 0x02000},
+                       {"default-mac", 0x30000, 0x00020},
+                       {"product-info", 0x31100, 0x00100},
+                       {"device-info", 0x31400, 0x00400},
+                       {"signature", 0x32000, 0x00400},
+                       {"device-id", 0x33000, 0x00100},
+                       {"os-image", 0x40000, 0x1c0000},
+                       {"file-system", 0x200000, 0x5b0000},
+                       {"soft-version", 0x7b0000, 0x00100},
+                       {"support-list", 0x7b1000, 0x01000},
+                       {"user-config", 0x7c0000, 0x10000},
+                       {"default-config", 0x7d0000, 0x10000},
+                       {"log", 0x7e0000, 0x10000},
+                       {"radio", 0x7f0000, 0x10000},
+                       {NULL, 0, 0}
+               },
+
+               .first_sysupgrade_partition = "os-image",
+               .last_sysupgrade_partition = "support-list",
+       },
+
        /** Firmware layout for the CPE510/520 */
        {
                .id     = "CPE510",