ramips: add support for Linksys EA7300 v2
authorJ. Scott Heppler <shep971@centurylink.net>
Wed, 23 Sep 2020 02:30:45 +0000 (19:30 -0700)
committerAdrian Schmutzler <freifunk@adrianschmutzler.de>
Wed, 23 Sep 2020 10:17:32 +0000 (12:17 +0200)
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>

Specifications:

*  SoC:            MediaTek  MT7621A            (880  MHz  2c/4t)
*  RAM:            Winbond W632GG6MB-12         (256M  DDR3-1600)
*  Flash:          Winbond W29N01HVSINA         (128M  NAND)
*  Eth:            MediaTek  MT7621A            (10/100/1000  Mbps  x5)
*  Radio:          MT7603E/MT7615N              (2.4  GHz  &  5  GHz)
                     4  antennae:  1  internal  and  3  non-deatachable
*  USB:            3.0  (x1)
*  LEDs:
          White    (x1  logo)
          Green    (x6  eth  +  wps)
          Orange   (x5,  hardware-bound)
*  Buttons:
          Reset    (x1)
          WPS      (x1)

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
package/boot/uboot-envtools/files/ramips
target/linux/ramips/dts/mt7621_linksys_ea7300-v2.dts [new file with mode: 0644]
target/linux/ramips/image/mt7621.mk
target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
target/linux/ramips/mt7621/base-files/etc/board.d/02_network
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
target/linux/ramips/mt7621/base-files/etc/init.d/bootcount
target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh

index 6ff04b2..14c12bb 100644 (file)
@@ -40,6 +40,7 @@ ravpower,rp-wd03)
                ubootenv_add_uci_config "/dev/mtd$idx" "0x4000" "0x1000" "0x1000"
        ;;
 linksys,ea7300-v1|\
+linksys,ea7300-v2|\
 linksys,ea7500-v2|\
 xiaomi,mi-router-ac2100|\
 xiaomi,mir3p|\
diff --git a/target/linux/ramips/dts/mt7621_linksys_ea7300-v2.dts b/target/linux/ramips/dts/mt7621_linksys_ea7300-v2.dts
new file mode 100644 (file)
index 0000000..f7330d1
--- /dev/null
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621_linksys_ea7xxx.dtsi"
+
+/ {
+       compatible = "linksys,ea7300-v2", "mediatek,mt7621-soc";
+       model = "Linksys EA7300 v2";
+
+       aliases {
+               led-boot = &led_power;
+               led-failsafe = &led_power;
+               led-running = &led_power;
+               led-upgrade = &led_power;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               wan_green {
+                       label = "ea7300-v2:green:wan";
+                       gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+               };
+
+               lan1_green {
+                       label = "ea7300-v2:green:lan1";
+                       gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+               };
+
+               lan2_green {
+                       label = "ea7300-v2:green:lan2";
+                       gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+               };
+
+               lan3_green {
+                       label = "ea7300-v2:green:lan3";
+                       gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+               };
+
+               lan4_green {
+                       label = "ea7300-v2:green:lan4";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+               };
+
+               led_power: power {
+                       label = "ea7300-v2:white:power";
+                       gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+               };
+
+               wps {
+                       label = "ea7300-v2:green:wps";
+                       gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+               };
+       };
+};
index 7862956..274d9f7 100644 (file)
@@ -655,6 +655,15 @@ define Device/linksys_ea7300-v1
 endef
 TARGET_DEVICES += linksys_ea7300-v1
 
+define Device/linksys_ea7300-v2
+  $(Device/linksys_ea7xxx)
+  DEVICE_MODEL := EA7300
+  DEVICE_VARIANT := v2
+  LINKSYS_HWNAME := EA7300v2
+  DEVICE_PACKAGES += kmod-mt7603
+endef
+TARGET_DEVICES += linksys_ea7300-v2
+
 define Device/linksys_ea7500-v2
   $(Device/linksys_ea7xxx)
   DEVICE_MODEL := EA7500
index c5cd446..8c3be54 100755 (executable)
@@ -42,6 +42,7 @@ gnubee,gb-pc2)
        ucidef_set_led_netdev "lan2" "lan2" "$boardname:green:lan2" "lan2"
        ;;
 linksys,ea7300-v1|\
+linksys,ea7300-v2|\
 linksys,ea7500-v2)
        ucidef_set_led_netdev "lan1" "lan1 link" "$boardname:green:lan1" "lan1" "link"
        ucidef_set_led_netdev "lan2" "lan2 link" "$boardname:green:lan2" "lan2" "link"
index 1c1d0e4..2606347 100755 (executable)
@@ -105,6 +105,7 @@ ramips_setup_macs()
                label_mac=$wan_mac
                ;;
        linksys,ea7300-v1|\
+       linksys,ea7300-v2|\
        linksys,ea7500-v2)
                lan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
                wan_mac=$lan_mac
index 3f7fdc1..b7a41f0 100644 (file)
@@ -11,6 +11,7 @@ board=$(board_name)
 
 case "$board" in
        linksys,ea7300-v1|\
+       linksys,ea7300-v2|\
        linksys,ea7500-v2)
                hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
                [ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 1 > /sys${DEVPATH}/macaddress
index b17161a..7ef0053 100755 (executable)
@@ -9,6 +9,7 @@ boot() {
                        echo -e "bootcount\nbootchanged\n" | /usr/sbin/fw_setenv -s -
                ;;
        linksys,ea7300-v1|\
+       linksys,ea7300-v2|\
        linksys,ea7500-v2)
                mtd resetbc s_env || true
                ;;
index b1feea7..442e78d 100755 (executable)
@@ -49,6 +49,7 @@ platform_do_upgrade() {
        dlink,dir-2660-a1|\
        hiwifi,hc5962|\
        linksys,ea7300-v1|\
+       linksys,ea7300-v2|\
        linksys,ea7500-v2|\
        netgear,r6220|\
        netgear,r6260|\