# CONFIG_SENSORS_NCT6775 is not set
# CONFIG_SENSORS_NCT7802 is not set
# CONFIG_SENSORS_NCT7904 is not set
+# CONFIG_SENSORS_NSA320 is not set
# CONFIG_SENSORS_NTC_THERMISTOR is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
CPU_TYPE:=xscale
MAINTAINER:=Luka Perkov <luka@openwrt.org>
-KERNEL_PATCHVER:=4.4
+KERNEL_PATCHVER:=4.9
include $(INCLUDE_DIR)/target.mk
name="pogo_e02"
;;
- "Linksys EA3500")
+ "Linksys Audi (EA3500)")
name="linksys-audi"
;;
- "Linksys E4200v2 / EA4500")
+ "Linksys Viper (E4200v2 / EA4500)")
name="linksys-viper"
;;
--- /dev/null
+CONFIG_ALIGNMENT_TRAP=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_SG_CHAIN=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+CONFIG_ARCH_MULTIPLATFORM=y
+CONFIG_ARCH_MULTI_CPU_AUTO=y
+# CONFIG_ARCH_MULTI_V4 is not set
+# CONFIG_ARCH_MULTI_V4T is not set
+CONFIG_ARCH_MULTI_V4_V5=y
+CONFIG_ARCH_MULTI_V5=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_ARCH_NR_GPIO=0
+# CONFIG_ARCH_OXNAS is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARCH_WANT_LIBATA_LEDS=y
+CONFIG_ARM=y
+# CONFIG_ARMADA_THERMAL is not set
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
+CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
+# CONFIG_ARM_CPU_SUSPEND is not set
+CONFIG_ARM_HAS_SG_CHAIN=y
+# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
+# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_THUMB is not set
+CONFIG_ATA=y
+CONFIG_ATAGS=y
+CONFIG_ATA_LEDS=y
+CONFIG_AUTO_ZRELADDR=y
+# CONFIG_BINFMT_FLAT is not set
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_MQ_PCI=y
+CONFIG_CACHE_FEROCEON_L2=y
+# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_MMIO=y
+CONFIG_CLKSRC_OF=y
+CONFIG_CLKSRC_PROBE=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+# CONFIG_CPU_BIG_ENDIAN is not set
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_FEROCEON=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FEROCEON=y
+# CONFIG_CPU_FEROCEON_OLD_ID is not set
+# CONFIG_CPU_ICACHE_DISABLE is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_PABRT_LEGACY=y
+CONFIG_CPU_PM=y
+CONFIG_CPU_TLB_FEROCEON=y
+CONFIG_CPU_USE_DOMAINS=y
+CONFIG_CRC16=y
+# CONFIG_CRC32_SARWATE is not set
+CONFIG_CRC32_SLICEBY8=y
+CONFIG_CRYPTO_CRC32C=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_DEV_MARVELL_CESA=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
+CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y
+# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
+CONFIG_DEBUG_UART_8250=y
+# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
+CONFIG_DEBUG_UART_8250_SHIFT=2
+# CONFIG_DEBUG_UART_8250_WORD is not set
+CONFIG_DEBUG_UART_PHYS=0xf1012000
+CONFIG_DEBUG_UART_VIRT=0xfed12000
+CONFIG_DEBUG_UNCOMPRESS=y
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DLCI is not set
+CONFIG_DNOTIFY=y
+CONFIG_DTC=y
+# CONFIG_EARLY_PRINTK is not set
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_EXT4_FS=y
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+CONFIG_FRAME_POINTER=y
+CONFIG_FS_MBCACHE=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ATOMIC64=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IO=y
+CONFIG_GENERIC_IRQ_CHIP=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GLOB=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_MVEBU=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+# CONFIG_HAVE_ARCH_BITREVERSE is not set
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
+CONFIG_HAVE_CBPF_JIT=y
+CONFIG_HAVE_CC_STACKPROTECTOR=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_API_DEBUG=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_MEMBLOCK=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ_FIXED=0
+CONFIG_HZ_PERIODIC=y
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MV64XXX=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_IOMMU_HELPER=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_JBD2=y
+CONFIG_KIRKWOOD_CLK=y
+CONFIG_KIRKWOOD_THERMAL=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_NETXBIG=y
+CONFIG_LEDS_NS2=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_LIBFDT=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MACH_KIRKWOOD=y
+CONFIG_MACH_MVEBU_ANY=y
+CONFIG_MANGLE_BOOTARGS=y
+CONFIG_MDIO_BOARDINFO=y
+# CONFIG_MFD_MAX77620 is not set
+CONFIG_MIGHT_HAVE_PCI=y
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_MVSDIO=y
+# CONFIG_MMC_TIFM_SD is not set
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MTD_CFI is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_ECC=y
+CONFIG_MTD_NAND_ORION=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MULTI_IRQ_HANDLER=y
+CONFIG_MV643XX_ETH=y
+CONFIG_MVEBU_CLK_COMMON=y
+CONFIG_MVEBU_MBUS=y
+CONFIG_MVMDIO=y
+# CONFIG_MVNETA is not set
+CONFIG_MVSW61XX_PHY=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEED_KUSER_HELPERS=y
+CONFIG_NEED_PER_CPU_KM=y
+CONFIG_NLS=y
+CONFIG_NO_BOOTMEM=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_ADDRESS_PCI=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_PCI=y
+CONFIG_OF_PCI_IRQ=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_ORION_IRQCHIP=y
+CONFIG_ORION_TIMER=y
+CONFIG_ORION_WATCHDOG=y
+CONFIG_OUTER_CACHE=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+CONFIG_PCI_MVEBU=y
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PHY_MVEBU_SATA=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_KIRKWOOD=y
+CONFIG_PINCTRL_MVEBU=y
+# CONFIG_PINCTRL_SINGLE is not set
+CONFIG_PLAT_ORION=y
+CONFIG_POWER_RESET=y
+# CONFIG_POWER_RESET_BRCMKONA is not set
+CONFIG_POWER_RESET_GPIO=y
+# CONFIG_POWER_RESET_QNAP is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_RATIONAL=y
+# CONFIG_RCU_STALL_COMMON is not set
+CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
+CONFIG_REGMAP_SPI=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MV=y
+CONFIG_RTC_I2C_AND_SPI=y
+CONFIG_RTC_MC146818_LIB=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_SATA_MV=y
+# CONFIG_SCHED_INFO is not set
+CONFIG_SCSI=y
+CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
+CONFIG_SERIAL_8250_FSL=y
+# CONFIG_SERIAL_MVEBU_UART is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SG_POOL=y
+CONFIG_SOC_BUS=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_ORION=y
+CONFIG_SPLIT_PTLOCK_CPUS=999999
+CONFIG_SRAM=y
+CONFIG_SRCU=y
+CONFIG_SWCONFIG=y
+CONFIG_SWIOTLB=y
+CONFIG_SWPHY=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_OF=y
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+CONFIG_USB=y
+CONFIG_USB_COMMON=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_ORION=y
+# CONFIG_USB_EHCI_HCD_PLATFORM is not set
+CONFIG_USB_EHCI_PCI=y
+CONFIG_USB_LED_TRIG=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SUPPORT=y
+# CONFIG_USB_UHCI_HCD is not set
+CONFIG_USE_OF=y
+CONFIG_VECTORS_BASE=0xffff0000
+# CONFIG_VFP is not set
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_WAN=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
--- /dev/null
+--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
++++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
+@@ -117,13 +117,13 @@
+ };
+
+ partition@100000 {
+- label = "uImage";
+- reg = <0x0100000 0x600000>;
++ label = "second stage u-boot";
++ reg = <0x100000 0x200000>;
+ };
+
+- partition@700000 {
+- label = "root";
+- reg = <0x0700000 0xf900000>;
++ partition@200000 {
++ label = "ubi";
++ reg = <0x200000 0xfe00000>;
+ };
+
+ };
--- /dev/null
+--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
++++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
+@@ -145,28 +145,23 @@
+ status = "okay";
+
+ partition@0 {
+- label = "uboot";
+- reg = <0x0000000 0xc0000>;
++ label = "u-boot";
++ reg = <0x0000000 0xe0000>;
+ };
+
+- partition@a0000 {
+- label = "env";
+- reg = <0xa0000 0x20000>;
++ partition@e0000 {
++ label = "u-boot environment";
++ reg = <0xe0000 0x100000>;
+ };
+
+ partition@100000 {
+- label = "zImage";
+- reg = <0x100000 0x300000>;
++ label = "second stage u-boot";
++ reg = <0x100000 0x200000>;
+ };
+
+- partition@540000 {
+- label = "initrd";
+- reg = <0x540000 0x300000>;
+- };
+-
+- partition@980000 {
+- label = "boot";
+- reg = <0x980000 0x1f400000>;
++ partition@200000 {
++ label = "ubi";
++ reg = <0x200000 0x1fe00000>;
+ };
+ };
+
--- /dev/null
+--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
++++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
+@@ -77,18 +77,22 @@
+
+ partition@0 {
+ label = "u-boot";
+- reg = <0x0000000 0x100000>;
+- read-only;
++ reg = <0x0000000 0xe0000>;
++ };
++
++ partition@e0000 {
++ label = "u-boot environment";
++ reg = <0xe0000 0x100000>;
+ };
+
+ partition@100000 {
+- label = "uImage";
+- reg = <0x0100000 0x400000>;
++ label = "second stage u-boot";
++ reg = <0x100000 0x200000>;
+ };
+
+- partition@500000 {
+- label = "data";
+- reg = <0x0500000 0xfb00000>;
++ partition@200000 {
++ label = "ubi";
++ reg = <0x200000 0xfe00000>;
+ };
+ };
+
--- /dev/null
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -220,6 +220,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ kirkwood-linkstation-lswsxl.dtb \
+ kirkwood-linkstation-lswvl.dtb \
+ kirkwood-linkstation-lswxl.dtb \
++ kirkwood-linksys-audi.dtb \
+ kirkwood-linksys-viper.dtb \
+ kirkwood-lschlv2.dtb \
+ kirkwood-lsxhl.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
+@@ -0,0 +1,245 @@
++/*
++ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
++ *
++ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
++ * (c) 2013 Deutsche Telekom Innovation Laboratories
++ * (c) 2014 Luka Perkov <luka@openwrt.org>
++ * (c) 2014 Dan Walters <dan@walters.io>
++ *
++ * This file is licensed under the terms of the GNU General Public
++ * License version 2. This program is licensed "as is" without any
++ * warranty of any kind, whether express or implied.
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6282.dtsi"
++
++/ {
++ model = "Linksys Audi (EA3500)";
++ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
++
++ memory {
++ device_type = "memory";
++ reg = <0x00000000 0x4000000>;
++ };
++
++ aliases {
++ serial0 = &uart0;
++ };
++
++ chosen {
++ stdout-path = "serial0:115200n8";
++ };
++
++ gpio_keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
++ pinctrl-names = "default";
++
++ wps {
++ label = "WPS Button";
++ linux,code = <KEY_WPS_BUTTON>;
++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
++ };
++
++ reset {
++ label = "Reset Button";
++ linux,code = <KEY_RESTART>;
++ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++ pinctrl-0 = < &pmx_led_green_power >;
++ pinctrl-names = "default";
++
++ green-power {
++ label = "audi:green:power";
++ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
++ };
++ };
++
++ mvsw61xx {
++ compatible = "marvell,88e6171";
++ status = "okay";
++ reg = <0x10>;
++
++ mii-bus = <&mdio>;
++ cpu-port-0 = <5>;
++ cpu-port-1 = <6>;
++ is-indirect;
++ };
++
++ dsa {
++ compatible = "marvell,dsa";
++ #address-cells = <2>;
++ #size-cells = <0>;
++
++ dsa,ethernet = <ð0port>;
++ dsa,mii-bus = <&mdio>;
++
++ switch@16,0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ reg = <16 0>; /* MDIO address 16, switch 0 in tree */
++
++ port@0 {
++ reg = <0>;
++ label = "ethernet1";
++ };
++
++ port@1 {
++ reg = <1>;
++ label = "ethernet2";
++ };
++
++ port@2 {
++ reg = <2>;
++ label = "ethernet3";
++ };
++
++ port@3 {
++ reg = <3>;
++ label = "ethernet4";
++ };
++
++ port@4 {
++ reg = <4>;
++ label = "internet";
++ };
++
++ port@5 {
++ reg = <5>;
++ label = "cpu";
++ };
++ };
++ };
++};
++
++&pinctrl {
++ pmx_led_green_power: pmx-led-green-power {
++ marvell,pins = "mpp7";
++ marvell,function = "gpo";
++ };
++ pmx_btn_wps: pmx-btn-wps {
++ marvell,pins = "mpp47";
++ marvell,function = "gpio";
++ };
++ pmx_btn_reset: pmx-btn-reset {
++ marvell,pins = "mpp48";
++ marvell,function = "gpio";
++ };
++};
++
++&nand {
++ status = "okay";
++ pinctrl-0 = <&pmx_nand>;
++ pinctrl-names = "default";
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition@0 {
++ label = "u-boot";
++ reg = <0x0 0x80000>;
++ read-only;
++ };
++
++ partition@80000 {
++ label = "u_env";
++ reg = <0x80000 0x4000>;
++ };
++
++ partition@84000 {
++ label = "s_env";
++ reg = <0x84000 0x4000>;
++ };
++
++ partition@200000 {
++ label = "kernel1";
++ reg = <0x200000 0x290000>;
++ };
++
++ partition@490000 {
++ label = "rootfs1";
++ reg = <0x490000 0x1170000>;
++ };
++
++ partition@1600000 {
++ label = "kernel2";
++ reg = <0x1600000 0x290000>;
++ };
++
++ partition@1890000 {
++ label = "rootfs2";
++ reg = <0x1890000 0x1170000>;
++ };
++
++ partition@2a00000 {
++ label = "syscfg";
++ reg = <0x2a00000 0x1600000>;
++ };
++
++ partition@88000 {
++ label = "unused";
++ reg = <0x88000 0x178000>;
++ };
++
++ };
++};
++
++&pciec {
++ status = "okay";
++};
++
++&pcie0 {
++ status = "okay";
++};
++
++&pcie1 {
++ status = "okay";
++};
++
++&mdio {
++ status = "okay";
++};
++
++&uart0 {
++ status = "okay";
++};
++
++/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
++ * fixed speed and duplex.
++ */
++ð0 {
++ status = "okay";
++ ethernet0-port@0 {
++ speed = <1000>;
++ duplex = <1>;
++ };
++};
++
++/* eth1 is connected to the switch at port 6. However DSA only supports a
++ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
++ */
++ð1 {
++ status = "okay";
++ ethernet1-port@0 {
++ speed = <1000>;
++ duplex = <1>;
++ };
++};
++
++/* There is no battery on the board, so the RTC does not keep
++ * time when there is no power, making it useless.
++ */
++&rtc {
++ status = "disabled";
++};
--- /dev/null
+--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
++++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+@@ -69,6 +69,17 @@
+ };
+ };
+
++ mvsw61xx {
++ compatible = "marvell,88e6171";
++ status = "okay";
++ reg = <0x10>;
++
++ mii-bus = <&mdio>;
++ cpu-port-0 = <5>;
++ cpu-port-1 = <6>;
++ is-indirect;
++ };
++
+ dsa {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+@@ -161,22 +172,22 @@
+ };
+
+ partition@200000 {
+- label = "kernel";
++ label = "kernel1";
+ reg = <0x200000 0x2A0000>;
+ };
+
+ partition@4A0000 {
+- label = "rootfs";
++ label = "rootfs1";
+ reg = <0x4A0000 0x1760000>;
+ };
+
+ partition@1C00000 {
+- label = "alt_kernel";
++ label = "kernel2";
+ reg = <0x1C00000 0x2A0000>;
+ };
+
+ partition@1EA0000 {
+- label = "alt_rootfs";
++ label = "rootfs2";
+ reg = <0x1EA0000 0x1760000>;
+ };
+
+@@ -225,10 +236,14 @@
+ };
+
+ /* eth1 is connected to the switch at port 6. However DSA only supports a
+- * single CPU port. So leave this port disabled to avoid confusion.
++ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
+ */
+ ð1 {
+- status = "disabled";
++ status = "okay";
++ ethernet1-port@0 {
++ speed = <1000>;
++ duplex = <1>;
++ };
+ };
+
+ /* There is no battery on the board, so the RTC does not keep
--- /dev/null
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -207,6 +207,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ kirkwood-ds411.dtb \
+ kirkwood-ds411j.dtb \
+ kirkwood-ds411slim.dtb \
++ kirkwood-goflexhome.dtb \
+ kirkwood-goflexnet.dtb \
+ kirkwood-guruplug-server-plus.dtb \
+ kirkwood-ib62x0.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
+@@ -0,0 +1,117 @@
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++
++/ {
++ model = "Seagate GoFlex Home";
++ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++ memory {
++ device_type = "memory";
++ reg = <0x00000000 0x8000000>;
++ };
++
++ chosen {
++ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
++ stdout-path = &uart0;
++ };
++
++ ocp@f1000000 {
++ pinctrl: pin-controller@10000 {
++ pmx_usb_power_enable: pmx-usb-power-enable {
++ marvell,pins = "mpp29";
++ marvell,function = "gpio";
++ };
++ pmx_led_white: pmx-led-white {
++ marvell,pins = "mpp40";
++ marvell,function = "gpio";
++ };
++ pmx_led_green: pmx-led_green {
++ marvell,pins = "mpp46";
++ marvell,function = "gpio";
++ };
++ pmx_led_orange: pmx-led-orange {
++ marvell,pins = "mpp47";
++ marvell,function = "gpio";
++ };
++ };
++ serial@12000 {
++ status = "ok";
++ };
++
++ sata@80000 {
++ status = "okay";
++ nr-ports = <2>;
++ };
++
++ };
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ health {
++ label = "status:green:health";
++ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "default-on";
++ };
++ fault {
++ label = "status:orange:fault";
++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
++ };
++ misc {
++ label = "status:white:misc";
++ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "disk-activity";
++ };
++ };
++ regulators {
++ compatible = "simple-bus";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-0 = <&pmx_usb_power_enable>;
++ pinctrl-names = "default";
++
++ usb_power: regulator@1 {
++ compatible = "regulator-fixed";
++ reg = <1>;
++ regulator-name = "USB Power";
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ enable-active-high;
++ regulator-always-on;
++ regulator-boot-on;
++ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++ };
++ };
++};
++
++&nand {
++ chip-delay = <40>;
++ status = "okay";
++
++ partition@0 {
++ label = "u-boot";
++ reg = <0x0000000 0x100000>;
++ read-only;
++ };
++
++ partition@100000 {
++ label = "ubi";
++ reg = <0x100000 0x0ff00000>;
++ };
++};
++
++&mdio {
++ status = "okay";
++
++ ethphy0: ethernet-phy@0 {
++ reg = <0>;
++ };
++};
++
++ð0 {
++ status = "okay";
++ ethernet0-port@0 {
++ phy-handle = <ðphy0>;
++ };
++};
--- /dev/null
+--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
++++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
+@@ -158,18 +158,8 @@
+ };
+
+ partition@100000 {
+- label = "uImage";
+- reg = <0x0100000 0x400000>;
+- };
+-
+- partition@500000 {
+- label = "pogoplug";
+- reg = <0x0500000 0x2000000>;
+- };
+-
+- partition@2500000 {
+- label = "root";
+- reg = <0x02500000 0xd800000>;
++ label = "ubi";
++ reg = <0x0100000 0x0ff00000>;
+ };
+ };
+
--- /dev/null
+--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
++++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
+@@ -111,40 +111,16 @@
+
+ partition@0 {
+ label = "uboot";
+- reg = <0x0000000 0x0100000>;
++ reg = <0x0000000 0x00c0000>;
+ read-only;
+ };
+ partition@100000 {
+ label = "uboot_env";
+- reg = <0x0100000 0x0080000>;
++ reg = <0x00c0000 0x0080000>;
+ };
+- partition@180000 {
+- label = "key_store";
+- reg = <0x0180000 0x0080000>;
+- };
+- partition@200000 {
+- label = "info";
+- reg = <0x0200000 0x0080000>;
+- };
+- partition@280000 {
+- label = "etc";
+- reg = <0x0280000 0x0a00000>;
+- };
+- partition@c80000 {
+- label = "kernel_1";
+- reg = <0x0c80000 0x0a00000>;
+- };
+- partition@1680000 {
+- label = "rootfs1";
+- reg = <0x1680000 0x2fc0000>;
+- };
+- partition@4640000 {
+- label = "kernel_2";
+- reg = <0x4640000 0x0a00000>;
+- };
+- partition@5040000 {
+- label = "rootfs2";
+- reg = <0x5040000 0x2fc0000>;
++ partition@140000 {
++ label = "ubi";
++ reg = <0x0140000 0x7ec0000>;
+ };
+ };
+
--- /dev/null
+kirkwood: add nsa310b dtb, a zyxel nsa310 variant
+
+add support to a nsa310 variant with red/green usb led
+and lm85 temp/fan controller
+
+Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
+
+NOTE: this patch can be upstreamed as-is, LEDE-specific
+ nand partitions are set in another patch
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -238,6 +238,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ kirkwood-ns2mini.dtb \
+ kirkwood-nsa310.dtb \
+ kirkwood-nsa310a.dtb \
++ kirkwood-nsa310b.dtb \
+ kirkwood-nsa320.dtb \
+ kirkwood-nsa325.dtb \
+ kirkwood-openblocks_a6.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
+@@ -0,0 +1,124 @@
++/dts-v1/;
++
++#include "kirkwood-nsa3x0-common.dtsi"
++
++/*
++ * There are at least two different NSA310 designs. This variant has
++ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
++ */
++
++/ {
++ model = "ZyXEL NSA310b";
++ compatible = "zyxel,nsa310a", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++ memory {
++ device_type = "memory";
++ reg = <0x00000000 0x10000000>;
++ };
++
++ chosen {
++ bootargs = "console=ttyS0,115200";
++ stdout-path = &uart0;
++ };
++
++ ocp@f1000000 {
++ pinctrl: pin-controller@10000 {
++ pinctrl-names = "default";
++
++ pmx_led_esata_green: pmx-led-esata-green {
++ marvell,pins = "mpp12";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_esata_red: pmx-led-esata-red {
++ marvell,pins = "mpp13";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_usb_green: pmx-led-usb-green {
++ marvell,pins = "mpp15";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_usb_red: pmx-led-usb-red {
++ marvell,pins = "mpp16";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_sys_green: pmx-led-sys-green {
++ marvell,pins = "mpp28";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_sys_red: pmx-led-sys-red {
++ marvell,pins = "mpp29";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_hdd_green: pmx-led-hdd-green {
++ marvell,pins = "mpp41";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_hdd_red: pmx-led-hdd-red {
++ marvell,pins = "mpp42";
++ marvell,function = "gpio";
++ };
++
++ };
++
++ i2c@11000 {
++ status = "okay";
++
++ lm85: lm85@2e {
++ compatible = "national,lm85";
++ reg = <0x2e>;
++ };
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ green-sys {
++ label = "nsa310:green:sys";
++ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++ };
++ red-sys {
++ label = "nsa310:red:sys";
++ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++ };
++ green-hdd {
++ label = "nsa310:green:hdd";
++ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
++ };
++ red-hdd {
++ label = "nsa310:red:hdd";
++ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
++ };
++ green-esata {
++ label = "nsa310:green:esata";
++ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++ };
++ red-esata {
++ label = "nsa310:red:esata";
++ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
++ };
++ green-usb {
++ label = "nsa310:green:usb";
++ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++ };
++ red-usb {
++ label = "nsa310:red:usb";
++ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
++ };
++ green-copy {
++ label = "nsa310:green:copy";
++ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
++ };
++ red-copy {
++ label = "nsa310:red:copy";
++ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
++ };
++ };
++};
--- /dev/null
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -239,6 +239,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ kirkwood-nsa310.dtb \
+ kirkwood-nsa310a.dtb \
+ kirkwood-nsa310b.dtb \
++ kirkwood-nsa310s.dtb \
+ kirkwood-nsa320.dtb \
+ kirkwood-nsa325.dtb \
+ kirkwood-openblocks_a6.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
+@@ -0,0 +1,254 @@
++/dts-v1/;
++
++#include "kirkwood-nsa3x0-common.dtsi"
++
++/ {
++ model = "ZyXEL NSA310S";
++ compatible = "zyxel,nsa320s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
++
++ memory {
++ device_type = "memory";
++ reg = <0x00000000 0x10000000>;
++ };
++
++ chosen {
++ bootargs = "console=ttyS0,115200n8 earlyprintk";
++ stdout-path = &uart0;
++ };
++
++ ocp@f1000000 {
++ pinctrl: pin-controller@10000 {
++ pinctrl-names = "default";
++
++ pmx_sata0: pmx-sata0 {
++ marvell,pins;
++ marvell,function = "sata0";
++ };
++
++ pmx_sata1: pmx-sata1 {
++ marvell,pins;
++ marvell,function = "sata1";
++ };
++
++ pmx_usb_power: pmx-usb-power {
++ marvell,pins = "mpp21";
++ marvell,function = "gpio";
++ };
++
++ pmx_pwr_off: pmx-pwr-off {
++ marvell,pins = "mpp27";
++ marvell,function = "gpio";
++ };
++
++ pmx_btn_reset: pmx-btn-reset {
++ marvell,pins = "mpp24";
++ marvell,function = "gpio";
++ };
++
++ pmx_btn_copy: pmx-btn-copy {
++ marvell,pins = "mpp25";
++ marvell,function = "gpio";
++ };
++
++ pmx_btn_power: pmx-btn-power {
++ marvell,pins = "mpp26";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_hdd2_green: pmx-led-hdd2-green {
++ marvell,pins = "mpp34";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_hdd2_red: pmx-led-hdd2-red {
++ marvell,pins = "mpp12";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_usb_green: pmx-led-usb-green {
++ marvell,pins = "mpp15";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_copy_green: pmx-led-copy-green {
++ marvell,pins = "mpp22";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_copy_red: pmx-led-copy-red {
++ marvell,pins = "mpp23";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_sys_green: pmx-led-sys-green {
++ marvell,pins = "mpp28";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_sys_orange: pmx-led-sys-orange {
++ marvell,pins = "mpp29";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_hdd1_green: pmx-led-hdd1-green {
++ marvell,pins = "mpp16";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_hdd1_red: pmx-led-hdd1-red {
++ marvell,pins = "mpp13";
++ marvell,function = "gpio";
++ };
++
++ pmx_pwr_sata1: pmx-pwr-sata1 {
++ marvell,pins = "mpp33";
++ marvell,function = "gpio";
++ };
++
++ };
++
++ i2c@11000 {
++ status = "okay";
++
++ ht1382: rtc@68 {
++ compatible = "htk,ht1382";
++ reg = <0x68>;
++ };
++ };
++ };
++
++ regulators {
++ compatible = "simple-bus";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-0 = <&pmx_pwr_sata1>;
++ pinctrl-names = "default";
++
++ usb0_power: regulator@1 {
++ enable-active-high;
++ };
++
++ sata1_power: regulator@2 {
++ compatible = "regulator-fixed";
++ reg = <2>;
++ regulator-name = "SATA1 Power";
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ regulator-always-on;
++ regulator-boot-on;
++ enable-active-high;
++ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
++ };
++ };
++
++ gpio_keys {
++ power {
++ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
++ };
++ copy {
++ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
++ };
++ reset {
++ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++
++ green-sys {
++ label = "nsa310s:green:sys";
++ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++ };
++ orange-sys {
++ label = "nsa310s:orange:sys";
++ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++ };
++ green-hdd1 {
++ label = "nsa310s:green:hdd1";
++ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
++ };
++ red-hdd1 {
++ label = "nsa310s:red:hdd1";
++ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
++ };
++ green-hdd2 {
++ label = "nsa310s:green:hdd2";
++ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
++ };
++ red-hdd2 {
++ label = "nsa310s:red:hdd2";
++ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
++ };
++ green-usb {
++ label = "nsa310s:green:usb";
++ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++ };
++ green-copy {
++ label = "nsa310s:green:copy";
++ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
++ };
++ red-copy {
++ label = "nsa310s:red:copy";
++ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
++ };
++ };
++
++ gpio_poweroff {
++ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
++ };
++};
++
++&nand {
++ status = "okay";
++ chip-delay = <35>;
++
++ partition@0 {
++ label = "uboot";
++ reg = <0x0000000 0xe0000>;
++ read-only;
++ };
++
++ partition@e0000 {
++ label = "uboot_env";
++ reg = <0xe0000 0x100000>;
++ };
++
++ partition@100000 {
++ label = "second stage u-boot";
++ reg = <0x100000 0x200000>;
++ };
++
++ partition@200000 {
++ label = "ubi";
++ reg = <0x200000 0x7e00000>;
++ };
++};
++
++&sata {
++ status = "okay";
++ nr-ports = <2>;
++};
++
++&mdio {
++ status = "okay";
++ ethphy0: ethernet-phy@1 {
++ compatible = "marvell,88e1318s";
++ reg = <1>;
++ marvell,reg-init = <0x1 0x16 0x0 0x3>,
++ <0x1 0x10 0x0 0x1017>,
++ <0x1 0x11 0x0 0x4408>,
++ <0x1 0x16 0x0 0x0>,
++ <0x1 0x4 0x0 0x1e1>,
++ <0x1 0x9 0x0 0x300>,
++ <0x1 0x10 0x0 0x3860>,
++ <0x1 0x0 0x0 0x9140>;
++ };
++};
++
++ð0 {
++ status = "okay";
++ ethernet0-port@0 {
++ phy-handle = <ðphy0>;
++ };
++};
--- /dev/null
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-on100.dts
+@@ -0,0 +1,160 @@
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6282.dtsi"
++
++/ {
++ model = "Cisco Systems ON100";
++ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
++
++ memory {
++ device_type = "memory";
++ reg = <0x00000000 0x20000000>;
++ };
++
++ aliases {
++ serial0 = &uart0;
++ };
++
++ chosen {
++ bootargs = "console=ttyS0,115200n8 earlyprintk";
++ stdout-path = "serial0:115200n8";
++ };
++
++ gpio_keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-0 = <&pmx_btn_reset>;
++ pinctrl-names = "default";
++
++ button@1 {
++ label = "Reset Button";
++ linux,code = <KEY_RESTART>;
++ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ gpio-leds {
++ compatible = "gpio-leds";
++ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
++ pinctrl-names = "default";
++
++ health-g {
++ label = "on100:green:health";
++ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
++ };
++
++ health-r {
++ label = "on100:red:health";
++ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
++ };
++
++ health2-g {
++ label = "on100:green:health2";
++ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
++ };
++
++ health2-r {
++ label = "on100:red:health2";
++ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++ð0 {
++ status = "okay";
++
++ ethernet0-port@0 {
++ phy-handle = <ðphy0>;
++ phy-connection-type = "rgmii-id";
++ };
++};
++
++ð1 {
++ status = "okay";
++
++ ethernet1-port@0 {
++ phy-handle = <ðphy1>;
++ phy-connection-type = "rgmii-id";
++ };
++};
++
++&mdio {
++ status = "okay";
++
++ ethphy0: ethernet-phy@0 {
++ /* Marvell 88E1121R */
++ compatible = "ethernet-phy-id0141.0cb0",
++ "ethernet-phy-ieee802.3-c22";
++ reg = <0>;
++ };
++
++ ethphy1: ethernet-phy@1 {
++ /* Marvell 88E1121R */
++ compatible = "ethernet-phy-id0141.0cb0",
++ "ethernet-phy-ieee802.3-c22";
++ reg = <1>;
++ };
++};
++
++&nand {
++ status = "okay";
++
++ partition@0 {
++ label = "u-boot";
++ reg = <0x00000000 0x000a0000>;
++ read-only;
++ };
++
++ partition@a0000 {
++ label = "u-boot environment";
++ reg = <0x000a0000 0x00020000>;
++ read-only;
++ };
++
++ partition@c0000 {
++ label = "kernel";
++ reg = <0x000c0000 0x00540000>;
++ };
++
++ partition@600000 {
++ label = "ubi";
++ reg = <0x00600000 0x1fa00000>;
++ };
++};
++
++&pinctrl {
++ pmx_led_health_r: pmx-led-health-r {
++ marvell,pins = "mpp45";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_health_g: pmx-led-health-g {
++ marvell,pins = "mpp44";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_health2_r: pmx-led-health2-r {
++ marvell,pins = "mpp47";
++ marvell,function = "gpio";
++ };
++
++ pmx_led_health2_g: pmx-led-health2-g {
++ marvell,pins = "mpp46";
++ marvell,function = "gpio";
++ };
++
++ pmx_btn_reset: pmx-led-reset {
++ marvell,pins = "mpp31";
++ marvell,function = "gpio";
++ };
++};
++
++&sdio {
++ status = "okay";
++};
++
++&uart0 {
++ status = "okay";
++};
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -242,6 +242,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ kirkwood-nsa310s.dtb \
+ kirkwood-nsa320.dtb \
+ kirkwood-nsa325.dtb \
++ kirkwood-on100.dtb \
+ kirkwood-openblocks_a6.dtb \
+ kirkwood-openblocks_a7.dtb \
+ kirkwood-openrd-base.dtb \
--- /dev/null
+From: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
+Subject: [PATCH] net: mv643xx_eth: Make TSO disabled by default
+
+Data corruption has been observed to be produced by TSO. For instance,
+accessing files on a NFS-server with TSO enabled results in different data
+transferred each time.
+
+This has been observed only on Kirkwood platforms, i.e. with the mv643xx_eth
+driver. Same tests on platforms using the mvneta ethernet driver have
+passed without errors.
+
+Make TSO disabled by default for now, until we can found a proper fix
+for the regression.
+
+Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO')
+Reported-by: Slawomir Gajzner <slawomir.gajzner <at> gmail.com>
+Reported-by: Julien D'Ascenzio <jdascenzio <at> yahoo.fr>
+Signed-off-by: Ezequiel Garcia <ezequiel.garcia <at> free-electrons.com>
+---
+--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
++++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
+@@ -3197,11 +3197,11 @@ static int mv643xx_eth_probe(struct plat
+ dev->watchdog_timeo = 2 * HZ;
+ dev->base_addr = 0;
+
+- dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO;
++ dev->features = NETIF_F_SG | NETIF_F_IP_CSUM;
+ dev->vlan_features = dev->features;
+
+ dev->features |= NETIF_F_RXCSUM;
+- dev->hw_features = dev->features;
++ dev->hw_features = dev->features | NETIF_F_TSO;
+
+ dev->priv_flags |= IFF_UNICAST_FLT;
+ dev->gso_max_segs = MV643XX_MAX_TSO_SEGS;
--- /dev/null
+--- a/arch/arm/mach-mvebu/Kconfig
++++ b/arch/arm/mach-mvebu/Kconfig
+@@ -117,6 +117,7 @@ config MACH_DOVE
+ config MACH_KIRKWOOD
+ bool "Marvell Kirkwood boards"
+ depends on ARCH_MULTI_V5
++ select ARCH_WANT_LIBATA_LEDS
+ select CPU_FEROCEON
+ select GPIOLIB
+ select KIRKWOOD_CLK
--- /dev/null
+The WRT1900AC among other Linksys routers uses a dual-firmware layout.
+Dynamically rename the active partition to "ubi".
+
+Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
+---
+--- a/drivers/mtd/ofpart.c
++++ b/drivers/mtd/ofpart.c
+@@ -25,6 +25,8 @@ static bool node_has_compatible(struct d
+ return of_get_property(pp, "compatible", NULL);
+ }
+
++static int mangled_rootblock;
++
+ static int parse_ofpart_partitions(struct mtd_info *master,
+ const struct mtd_partition **pparts,
+ struct mtd_part_parser_data *data)
+@@ -32,6 +34,7 @@ static int parse_ofpart_partitions(struc
+ struct mtd_partition *parts;
+ struct device_node *mtd_node;
+ struct device_node *ofpart_node;
++ const char *owrtpart = "ubi";
+ const char *partname;
+ struct device_node *pp;
+ int nr_parts, i, ret = 0;
+@@ -110,9 +113,15 @@ static int parse_ofpart_partitions(struc
+ parts[i].size = of_read_number(reg + a_cells, s_cells);
+ parts[i].of_node = pp;
+
+- partname = of_get_property(pp, "label", &len);
+- if (!partname)
+- partname = of_get_property(pp, "name", &len);
++ if (mangled_rootblock && (i == mangled_rootblock)) {
++ partname = owrtpart;
++ } else {
++ partname = of_get_property(pp, "label", &len);
++
++ if (!partname)
++ partname = of_get_property(pp, "name", &len);
++ }
++
+ parts[i].name = partname;
+
+ if (of_get_property(pp, "read-only", &len))
+@@ -213,6 +222,18 @@ static int __init ofpart_parser_init(voi
+ return 0;
+ }
+
++static int __init active_root(char *str)
++{
++ get_option(&str, &mangled_rootblock);
++
++ if (!mangled_rootblock)
++ return 1;
++
++ return 1;
++}
++
++__setup("mangled_rootblock=", active_root);
++
+ static void __exit ofpart_parser_exit(void)
+ {
+ deregister_mtd_parser(&ofpart_parser);
projects / openwrt / openwrt.git / commitdiff