ath79: add support for ELECOM WRC-1750GHBK2-I/C
authorINAGAKI Hiroshi <musashino.open@gmail.com>
Sat, 29 Dec 2018 15:55:35 +0000 (00:55 +0900)
committerINAGAKI Hiroshi <musashino.open@gmail.com>
Mon, 31 Dec 2018 12:38:53 +0000 (21:38 +0900)
ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac
routers, based on Qualcomm Atheros QCA9563.

This commit also includes small fix; use "0x0x03000101" as pll_1000
instead of "0x03000000".

Specification:

- SoC:      Qualcom Atheros QCA9563
- RAM:      128 MB (DDR2)
- Flash:    16 MB (SPI-NOR)
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 10/100/1000 Mbps
- LED/key:  4x/3x (2x buttons, 1x slide-switch)
- UART:     through-hole on PCB
  - Vcc, RX, GND, TX from switch (QCA8337N) side
  - 115200n8

Flash instruction using factory image:

1. Boot WRC-1750GHBK2-I/C normaly
2. Access to "http://192.168.2.1/" and open firmware upgrade page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, perform sysupgrade with
squashfs-sysupgrade image
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ath79/dts/qca9563_elecom_wrc-1750ghbk2-i.dts [new file with mode: 0644]
target/linux/ath79/dts/qca9563_elecom_wrc-300ghbk2-i.dts
target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi [new file with mode: 0644]
target/linux/ath79/image/generic.mk

index 1be7a63c85293dbb143e1bccee7d5aa1c314c01c..83bede0961d46e61ea1c54b3f87f5b84d4d725a2 100755 (executable)
@@ -77,6 +77,7 @@ ath79_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
                ;;
+       elecom,wrc-1750ghbk2-i|\
        elecom,wrc-300ghbk2-i)
                ucidef_add_switch "switch0" \
                        "0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
@@ -244,6 +245,7 @@ ath79_setup_macs()
                lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
                wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
                ;;
+       elecom,wrc-1750ghbk2-i|\
        elecom,wrc-300ghbk2-i)
                wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
                ;;
index 7fe19c0604bbdad2cb383e6e4444b74c423a72f5..45d3819c216e62f53a1e65ba739757b0c36ebc1f 100644 (file)
@@ -96,6 +96,9 @@ case "$FIRMWARE" in
                ath10kcal_extract "art" 20480 2116
                ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
                ;;
+       elecom,wrc-1750ghbk2-i)
+               ath10kcal_extract "ART" 20480 2116
+               ;;
        glinet,ar750s|\
        tplink,re450-v2)
                ath10kcal_extract "art" 20480 2116
diff --git a/target/linux/ath79/dts/qca9563_elecom_wrc-1750ghbk2-i.dts b/target/linux/ath79/dts/qca9563_elecom_wrc-1750ghbk2-i.dts
new file mode 100644 (file)
index 0000000..287dee6
--- /dev/null
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca9563_elecom_wrc-ghbk2-i.dtsi"
+
+/ {
+       model = "ELECOM WRC-1750GHBK2-I/C";
+       compatible = "elecom,wrc-1750ghbk2-i", "qca,qca9563";
+};
+
+&leds {
+       power: power {
+               label = "elecom:blue:power";
+               gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+               default-state = "on";
+       };
+
+       wlan2g {
+               label = "elecom:blue:wlan2g";
+               gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+               linux,default-trigger = "phy1tpt";
+       };
+
+       wlan5g {
+               label = "elecom:blue:wlan5g";
+               gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+               linux,default-trigger = "phy0tpt";
+       };
+};
+
+&partitions {
+       partition@70000 {
+               compatible = "denx,uimage";
+               label = "firmware";
+               reg = <0x070000 0xf70000>;
+       };
+
+       partition@fe0000 {
+               label = "hwconfig";
+               reg = <0xfe0000 0x010000>;
+               read-only;
+       };
+
+       ART: partition@ff0000 {
+               label = "ART";
+               reg = <0xff0000 0x010000>;
+               read-only;
+       };
+};
+
+&pcie {
+       status = "okay";
+};
index bb1f350150e68fe94c0531dd0e1704c78c708bd2..c823f4a34281e5c694d1415177596479c09405c3 100644 (file)
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 
-#include "qca956x.dtsi"
+#include "qca9563_elecom_wrc-ghbk2-i.dtsi"
 
 / {
        model = "ELECOM WRC-300GHBK2-I";
        compatible = "elecom,wrc-300ghbk2-i", "qca,qca9563";
+};
 
-       chosen {
-               bootargs = "console=ttyS0,115200n8";
-       };
-
-       aliases {
-               led-boot = &power;
-               led-failsafe = &power;
-               led-running = &power;
-               led-upgrade = &power;
+&leds {
+       power: power {
+               label = "elecom:white:power";
+               gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+               default-state = "on";
        };
 
-       leds {
-               compatible = "gpio-leds";
-
-               power: power {
-                       label = "wrc-300ghbk2-i:white:power";
-                       gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
-                       default-state = "on";
-               };
-
-               wlan2g {
-                       label = "wrc-300ghbk2-i:white:wlan2g";
-                       gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
-                       linux,default-trigger = "phy0tpt";
-               };
-
-               wps {
-                       label = "wrc-300ghbk2-i:red:wps";
-                       gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
-               };
-       };
-
-       keys {
-               compatible = "gpio-keys";
-
-               reset {
-                       label = "reset";
-                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
-                       linux,code = <KEY_RESTART>;
-                       debounce-interval = <60>;
-               };
-
-               button_wps {
-                       label = "wps";
-                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
-                       linux,code = <KEY_WPS_BUTTON>;
-                       debounce-interval = <60>;
-               };
-
-               ap {
-                       label = "ap";
-                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
-                       linux,code = <BTN_0>;
-                       linux,input-type = <EV_SW>;
-                       debounce-interval = <60>;
-               };
+       wlan2g {
+               label = "elecom:white:wlan2g";
+               gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+               linux,default-trigger = "phy0tpt";
        };
 };
 
-&spi {
-       status = "okay";
-       num-cs = <1>;
-
-       flash@0 {
-               compatible = "jedec,spi-nor";
-               reg = <0>;
-               spi-max-frequency = <25000000>;
-
-               partitions {
-                       compatible = "fixed-partitions";
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-
-                       partition@0 {
-                               label = "u-boot";
-                               reg = <0x000000 0x040000>;
-                               read-only;
-                       };
-
-                       partition@40000 {
-                               label = "u-boot-env";
-                               reg = <0x040000 0x010000>;
-                               read-only;
-                       };
-
-                       partition@50000 {
-                               label = "nvram";
-                               reg = <0x050000 0x020000>;
-                               read-only;
-                       };
-
-                       partition@70000 {
-                               compatible = "denx,uimage";
-                               label = "firmware";
-                               reg = <0x070000 0x770000>;
-                       };
-
-                       partition@7e0000 {
-                               label = "hwconfig";
-                               reg = <0x7e0000 0x010000>;
-                               read-only;
-                       };
-
-                       ART: partition@7f0000 {
-                               label = "ART";
-                               reg = <0x7f0000 0x010000>;
-                               read-only;
-                       };
-               };
+&partitions {
+       partition@70000 {
+               compatible = "denx,uimage";
+               label = "firmware";
+               reg = <0x070000 0x770000>;
        };
-};
-
-&mdio0 {
-       status = "okay";
-
-       phy0: ethernet-phy@0 {
-               reg = <0>;
-               phy-mode = "sgmii";
 
-               qca,ar8327-initvals = <
-                       0x04 0x00000080 /* PORT0 PAD MODE CTRL */
-                       0x50 0xcf37cf37 /* LED_CTRL0 */
-                       0x54 0x00000000 /* LED_CTRL1 */
-                       0x58 0x00000000 /* LED_CTRL2 */
-                       0x5c 0x03ffff00 /* LED_CTRL3 */
-                       0x7c 0x0000007e /* PORT0_STATUS */
-               >;
+       partition@7e0000 {
+               label = "hwconfig";
+               reg = <0x7e0000 0x010000>;
+               read-only;
        };
-};
-
-&eth0 {
-       status = "okay";
-
-       mtd-mac-address = <&ART 0x1002>;
-       mtd-mac-address-increment = <(-1)>;
-       phy-mode = "sgmii";
-       phy-handle = <&phy0>;
-};
 
-&uart {
-       status = "okay";
-};
-
-&wmac {
-       status = "okay";
-       mtd-cal-data = <&ART 0x1000>;
+       ART: partition@7f0000 {
+               label = "ART";
+               reg = <0x7f0000 0x010000>;
+               read-only;
+       };
 };
diff --git a/target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi b/target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi
new file mode 100644 (file)
index 0000000..8d5bbe1
--- /dev/null
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+       chosen {
+               bootargs = "console=ttyS0,115200n8";
+       };
+
+       aliases {
+               led-boot = &power;
+               led-failsafe = &power;
+               led-running = &power;
+               led-upgrade = &power;
+       };
+
+       leds: leds {
+               compatible = "gpio-leds";
+
+               wps {
+                       label = "elecom:red:wps";
+                       gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+                       debounce-interval = <60>;
+               };
+
+               button_wps {
+                       label = "wps";
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+                       debounce-interval = <60>;
+               };
+
+               ap {
+                       label = "ap";
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+                       linux,code = <BTN_0>;
+                       linux,input-type = <EV_SW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions: partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x040000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x040000 0x010000>;
+                               read-only;
+                       };
+
+                       partition@50000 {
+                               label = "nvram";
+                               reg = <0x050000 0x020000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy0: ethernet-phy@0 {
+               reg = <0>;
+
+               qca,ar8327-initvals = <
+                       0x04 0x00000080 /* PORT0 PAD MODE CTRL */
+                       0x50 0xcf37cf37 /* LED_CTRL0 */
+                       0x54 0x00000000 /* LED_CTRL1 */
+                       0x58 0x00000000 /* LED_CTRL2 */
+                       0x5c 0x03ffff00 /* LED_CTRL3 */
+                       0x7c 0x0000007e /* PORT0_STATUS */
+               >;
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       pll-data = <0x03000101 0x00000101 0x00001919>;
+
+       mtd-mac-address = <&ART 0x1002>;
+       mtd-mac-address-increment = <(-1)>;
+       phy-mode = "sgmii";
+       phy-handle = <&phy0>;
+};
+
+&uart {
+       status = "okay";
+};
+
+&wmac {
+       status = "okay";
+       mtd-cal-data = <&ART 0x1000>;
+};
index 2f9b2c9d7ecfc28f4fefd517cac1183277de9ad0..31c62f659d291be79f14badbd00c46ecf4558ad9 100644 (file)
@@ -221,6 +221,17 @@ define Device/dlink_dir-859-a1
 endef
 TARGET_DEVICES += dlink_dir-859-a1
 
+define Device/elecom_wrc-1750ghbk2-i
+  ATH_SOC := qca9563
+  DEVICE_TITLE := ELECOM WRC-1750GHBK2-I/C
+  IMAGE_SIZE := 15808k
+  KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
+    elecom-header 16187314 RN68 WRC-1750GHBK2 \
+      $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin
+  DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
+endef
+TARGET_DEVICES += elecom_wrc-1750ghbk2-i
+
 define Device/elecom_wrc-300ghbk2-i
   ATH_SOC := qca9563
   DEVICE_TITLE := ELECOM WRC-300GHBK2-I