ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
authorPeng Zhang <sd20@qxwlan.com>
Fri, 5 Jan 2018 09:38:05 +0000 (17:38 +0800)
committerPiotr Dymacz <pepe2k@gmail.com>
Thu, 22 Feb 2018 17:53:22 +0000 (18:53 +0100)
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB

WHQX E600G is based on Qualcomm QCA9531.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB

WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB

Important notice:

First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!

Flash instruction (using U-Boot CLI and tftp server):

1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
15 files changed:
target/linux/ar71xx/base-files/etc/board.d/01_leds
target/linux/ar71xx/base-files/etc/board.d/02_network
target/linux/ar71xx/base-files/etc/diag.sh
target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ar71xx/base-files/lib/ar71xx.sh
target/linux/ar71xx/base-files/lib/upgrade/platform.sh
target/linux/ar71xx/config-4.4
target/linux/ar71xx/config-4.9
target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
target/linux/ar71xx/files/arch/mips/ath79/Makefile
target/linux/ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c [new file with mode: 0644]
target/linux/ar71xx/files/arch/mips/ath79/mach-e600g-v2.c [new file with mode: 0644]
target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
target/linux/ar71xx/generic/config-default
target/linux/ar71xx/image/generic.mk

index 6711fb4..725bab2 100755 (executable)
@@ -64,7 +64,9 @@ ap90q|\
 cpe505n|\
 cpe830|\
 cpe870|\
-dr531)
+dr531|\
+e600g-v2|\
+e600gac-v2)
        ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0"
        ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1"
 
@@ -342,6 +344,10 @@ dlan-pro-1200-ac)
        ucidef_set_led_gpio "plcw" "dLAN" "devolo:status:dlan" "17" "0"
        ucidef_set_led_gpio "plcr" "dLAN" "devolo:error:dlan" "16" "0"
        ;;
+e1700ac-v2)
+       ucidef_set_led_usbdev "usb" "USB" "$board:green:usb" "1-1"
+       ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
+       ;;
 esr900)
        ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "engenius:blue:wlan-2g" "phy0tpt"
        ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "engenius:blue:wlan-5g" "phy1tpt"
index f131b3b..0fe71e0 100755 (executable)
@@ -355,6 +355,12 @@ ar71xx_setup_interfaces()
                        "0u@eth0" "2:lan" "3:lan" "4:lan"
                ucidef_add_switch_attr "switch0" "enable" "false"
                ;;
+       e1700ac-v2|\
+       unifiac-pro|\
+       xd3200)
+               ucidef_add_switch "switch0" \
+                       "0@eth0" "2:lan" "3:wan"
+               ;;
        ebr-2310-c1)
                ucidef_set_interfaces_lan_wan "eth0.1" "eth1"
                ucidef_add_switch "switch0" \
@@ -493,11 +499,6 @@ ar71xx_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0@eth0" "1:lan" "2:wan"
                ;;
-       unifiac-pro|\
-       xd3200)
-               ucidef_add_switch "switch0" \
-                       "0@eth0" "2:lan" "3:wan"
-               ;;
        wndr3700|\
        wndr3700v2|\
        wndr3800|\
index 3b5fc32..facc77e 100644 (file)
@@ -23,6 +23,8 @@ get_status_led() {
        antminer-s1|\
        antminer-s3|\
        antminer-r1|\
+       e1700ac-v2|\
+       e600gac-v2|\
        eap120|\
        minibox-v1|\
        som9331|\
@@ -199,6 +201,9 @@ get_status_led() {
        r36a)
                status_led="$board:blue:status"
                ;;
+       e600g-v2)
+               status_led="$board:blue:system"
+               ;;
        eap300v2)
                status_led="engenius:blue:power"
                ;;
index 8284550..b0ada3b 100644 (file)
@@ -67,6 +67,8 @@ case "$FIRMWARE" in
        cf-e380ac-v1|\
        cf-e380ac-v2|\
        dlan-pro-1200-ac|\
+       e1700ac-v2|\
+       e600gac-v2|\
        sr3200|\
        xd3200)
                ath10kcal_extract "art" 20480 2116
index f0742c1..a9c6821 100755 (executable)
@@ -627,9 +627,18 @@ ar71xx_board_detect() {
        *"DW33D")
                name="dw33d"
                ;;
+       *"E1700AC v2")
+               name="e1700ac-v2"
+               ;;
        *"E2100L")
                name="e2100l"
                ;;
+       *"E600G v2")
+               name="e600g-v2"
+               ;;
+       *"E600GAC v2")
+               name="e600gac-v2"
+               ;;
        *"EAP120")
                name="eap120"
                tplink_pharos_board_detect
index 88d0f29..614692d 100755 (executable)
@@ -233,6 +233,9 @@ platform_check_image() {
        dr342|\
        dr531|\
        dragino2|\
+       e1700ac-v2|\
+       e600g-v2|\
+       e600gac-v2|\
        ebr-2310-c1|\
        ens202ext|\
        epg5000|\
index 068b83c..ec398a7 100644 (file)
@@ -99,7 +99,9 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_DR344 is not set
 # CONFIG_ATH79_MACH_DR531 is not set
 # CONFIG_ATH79_MACH_DRAGINO2 is not set
+# CONFIG_ATH79_MACH_E1700AC_V2 is not set
 # CONFIG_ATH79_MACH_E2100L is not set
+# CONFIG_ATH79_MACH_E600G_V2 is not set
 # CONFIG_ATH79_MACH_EAP120 is not set
 # CONFIG_ATH79_MACH_EAP300V2 is not set
 # CONFIG_ATH79_MACH_EAP7660D is not set
index e495f6b..924f17c 100644 (file)
@@ -97,7 +97,9 @@ CONFIG_ATH79=y
 # CONFIG_ATH79_MACH_DR344 is not set
 # CONFIG_ATH79_MACH_DR531 is not set
 # CONFIG_ATH79_MACH_DRAGINO2 is not set
+# CONFIG_ATH79_MACH_E1700AC_V2 is not set
 # CONFIG_ATH79_MACH_E2100L is not set
+# CONFIG_ATH79_MACH_E600G_V2 is not set
 # CONFIG_ATH79_MACH_EAP120 is not set
 # CONFIG_ATH79_MACH_EAP300V2 is not set
 # CONFIG_ATH79_MACH_EAP7660D is not set
index fca5d01..ad4e2a2 100644 (file)
@@ -689,6 +689,17 @@ config ATH79_MACH_DRAGINO2
        select ATH79_DEV_ETH
        select ATH79_DEV_USB
 
+config ATH79_MACH_E1700AC_V2
+       bool "WHQX E1700AC v2 support"
+       select SOC_QCA956X
+       select ATH79_DEV_AP9X_PCI if PCI
+       select ATH79_DEV_ETH
+       select ATH79_DEV_GPIO_BUTTONS
+       select ATH79_DEV_LEDS_GPIO
+       select ATH79_DEV_M25P80
+       select ATH79_DEV_USB
+       select ATH79_DEV_WMAC
+
 config ATH79_MACH_E2100L
        bool "Linksys E2100L board support"
        select SOC_AR913X
@@ -700,6 +711,17 @@ config ATH79_MACH_E2100L
        select ATH79_DEV_WMAC
        select ATH79_NVRAM
 
+config ATH79_MACH_E600G_V2
+       bool "WHQX E600G/E600GAC v2 support"
+       select SOC_QCA953X
+       select ATH79_DEV_AP9X_PCI if PCI
+       select ATH79_DEV_ETH
+       select ATH79_DEV_GPIO_BUTTONS
+       select ATH79_DEV_LEDS_GPIO
+       select ATH79_DEV_M25P80
+       select ATH79_DEV_USB
+       select ATH79_DEV_WMAC
+
 config ATH79_MACH_ESR900
        bool "EnGenius ESR900 board support"
        select SOC_QCA955X
index 98d4677..d489b1a 100644 (file)
@@ -108,6 +108,8 @@ obj-$(CONFIG_ATH79_MACH_DR342)                      += mach-dr344.o
 obj-$(CONFIG_ATH79_MACH_DR344)                 += mach-dr344.o
 obj-$(CONFIG_ATH79_MACH_DR531)                 += mach-dr531.o
 obj-$(CONFIG_ATH79_MACH_DRAGINO2)              += mach-dragino2.o
+obj-$(CONFIG_ATH79_MACH_E1700AC_V2)            += mach-e1700ac-v2.o
+obj-$(CONFIG_ATH79_MACH_E600G_V2)              += mach-e600g-v2.o
 obj-$(CONFIG_ATH79_MACH_EAP120)                        += mach-eap120.o
 obj-$(CONFIG_ATH79_MACH_EAP300V2)              += mach-eap300v2.o
 obj-$(CONFIG_ATH79_MACH_EAP7660D)              += mach-eap7660d.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-e1700ac-v2.c
new file mode 100644 (file)
index 0000000..584fd51
--- /dev/null
@@ -0,0 +1,145 @@
+/*
+ *  WHQX E1700AC v2 board support
+ *
+ *  Copyright (C) 2017 Peng Zhang <sd20@qxwlan.com>
+ *  Copyright (C) 2018 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/ar8216_platform.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define E1700AC_V2_GPIO_LED_SYS                1
+#define E1700AC_V2_GPIO_LED_USB                7
+#define E1700AC_V2_GPIO_LED_WLAN2G     19
+
+#define E1700AC_V2_GPIO_BTN_SW1                2
+#define E1700AC_V2_GPIO_BTN_RESET      11
+
+#define E1700AC_V2_KEYS_POLL_INTERVAL          20 /* msecs */
+#define E1700AC_V2_KEYS_DEBOUNCE_INTERVAL      \
+                                       (3 * E1700AC_V2_KEYS_POLL_INTERVAL)
+
+static struct gpio_led e1700ac_v2_leds_gpio[] __initdata = {
+       {
+               .name           = "e1700ac-v2:green:system",
+               .gpio           = E1700AC_V2_GPIO_LED_SYS,
+               .active_low     = 1,
+       }, {
+               .name           = "e1700ac-v2:green:usb",
+               .gpio           = E1700AC_V2_GPIO_LED_USB,
+               .active_low     = 1,
+       }, {
+               .name           = "e1700ac-v2:green:wlan2g",
+               .gpio           = E1700AC_V2_GPIO_LED_WLAN2G,
+               .active_low     = 1,
+       },
+};
+
+static struct gpio_keys_button e1700ac_v2_gpio_keys[] __initdata = {
+       {
+               .desc                   = "reset",
+               .type                   = EV_KEY,
+               .code                   = KEY_RESTART,
+               .debounce_interval      = E1700AC_V2_KEYS_DEBOUNCE_INTERVAL,
+               .gpio                   = E1700AC_V2_GPIO_BTN_RESET,
+               .active_low             = 1,
+       }, {
+               .desc                   = "sw1",
+               .type                   = EV_KEY,
+               .code                   = BTN_0,
+               .debounce_interval      = E1700AC_V2_KEYS_DEBOUNCE_INTERVAL,
+               .gpio                   = E1700AC_V2_GPIO_BTN_SW1,
+               .active_low             = 1,
+       },
+};
+
+static const struct ar8327_led_info e1700ac_v2_leds_qca8334[] = {
+       AR8327_LED_INFO(PHY1_0, HW, "e1700ac-v2:green:lan"),
+       AR8327_LED_INFO(PHY2_0, HW, "e1700ac-v2:green:wan"),
+};
+
+/* Blink rate: 1 Gbps -> 8 hz, 100 Mbs -> 4 Hz, 10 Mbps -> 2 Hz */
+static struct ar8327_led_cfg e1700ac_v2_qca8334_led_cfg = {
+       .led_ctrl0 = 0xcf37cf37,
+       .led_ctrl1 = 0xcf37cf37,
+       .led_ctrl2 = 0xcf37cf37,
+       .led_ctrl3 = 0x0,
+       .open_drain = true,
+};
+
+static struct ar8327_pad_cfg e1700ac_v2_qca8334_pad0_cfg = {
+       .mode = AR8327_PAD_MAC_SGMII,
+       .sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data e1700ac_v2_qca8334_data = {
+       .pad0_cfg = &e1700ac_v2_qca8334_pad0_cfg,
+       .port0_cfg = {
+               .force_link = 1,
+               .speed = AR8327_PORT_SPEED_1000,
+               .duplex = 1,
+               .txpause = 1,
+               .rxpause = 1,
+       },
+       .led_cfg = &e1700ac_v2_qca8334_led_cfg,
+       .leds = e1700ac_v2_leds_qca8334,
+       .num_leds = ARRAY_SIZE(e1700ac_v2_leds_qca8334),
+};
+
+static struct mdio_board_info e1700ac_v2_mdio0_info[] = {
+       {
+               .bus_id = "ag71xx-mdio.0",
+               .phy_addr = 0,
+               .platform_data = &e1700ac_v2_qca8334_data,
+       },
+};
+
+static void __init e1700ac_v2_setup(void)
+{
+       u8 *mac = (u8 *) KSEG1ADDR(0x1f050400);
+       u8 *art = (u8 *) KSEG1ADDR(0x1f061000);
+
+       ath79_register_m25p80(NULL);
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(e1700ac_v2_leds_gpio),
+                                e1700ac_v2_leds_gpio);
+
+       ath79_register_gpio_keys_polled(-1, E1700AC_V2_KEYS_POLL_INTERVAL,
+                                       ARRAY_SIZE(e1700ac_v2_gpio_keys),
+                                       e1700ac_v2_gpio_keys);
+
+       ath79_register_mdio(0, 0x0);
+       mdiobus_register_board_info(e1700ac_v2_mdio0_info,
+                                   ARRAY_SIZE(e1700ac_v2_mdio0_info));
+
+       /* GMAC0 is connected to QCA8334 switch */
+       ath79_eth0_data.duplex = DUPLEX_FULL;
+       ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+       ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+       ath79_eth0_data.phy_mask = BIT(0);
+       ath79_eth0_data.speed = SPEED_1000;
+       ath79_eth0_pll_data.pll_1000 = 0x03000101;
+       ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+       ath79_register_eth(0);
+
+       ath79_register_pci();
+       ath79_register_usb();
+       ath79_register_wmac(art, NULL);
+}
+
+MIPS_MACHINE(ATH79_MACH_E1700AC_V2, "E1700AC-V2", "WHQX E1700AC v2",
+            e1700ac_v2_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-e600g-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-e600g-v2.c
new file mode 100644 (file)
index 0000000..9838c30
--- /dev/null
@@ -0,0 +1,184 @@
+/*
+ *  WHQX E600G/E600GAC v2 board support
+ *
+ *  Copyright (C) 2017 Peng Zhang <sd20@qxwlan.com>
+ *  Copyright (C) 2018 Piotr Dymacz <pepe2k@gmail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define E600G_V2_GPIO_LED_LAN          16
+#define E600G_V2_GPIO_LED_SYS          13
+#define E600G_V2_GPIO_LED_WAN_B                4
+#define E600G_V2_GPIO_LED_WAN_G                15
+
+#define E600GAC_V2_GPIO_LED_CTRL_B     14
+#define E600GAC_V2_GPIO_LED_CTRL_G     11
+#define E600GAC_V2_GPIO_LED_CTRL_R     12
+#define E600GAC_V2_GPIO_LED_LAN                16
+#define E600GAC_V2_GPIO_LED_SYS                13
+#define E600GAC_V2_GPIO_LED_WAN_G      15
+#define E600GAC_V2_GPIO_LED_WAN_O      4
+
+#define E600G_V2_GPIO_BTN_RESET                17
+#define E600GAC_V2_GPIO_BTN_WPS                1
+
+#define E600G_V2_KEYS_POLL_INTERVAL    20 /* msecs */
+#define E600G_V2_KEYS_DEBOUNCE_INTERVAL        (3 * E600G_V2_KEYS_POLL_INTERVAL)
+
+static struct gpio_led e600g_v2_leds_gpio[] __initdata = {
+       {
+               .name           = "e600g-v2:blue:system",
+               .gpio           = E600G_V2_GPIO_LED_SYS,
+               .active_low     = 1,
+       }, {
+               .name           = "e600g-v2:blue:wan",
+               .gpio           = E600G_V2_GPIO_LED_WAN_B,
+               .active_low     = 1,
+       }, {
+               .name           = "e600g-v2:green:lan",
+               .gpio           = E600G_V2_GPIO_LED_LAN,
+               .active_low     = 1,
+       }, {
+               .name           = "e600g-v2:green:wan",
+               .gpio           = E600G_V2_GPIO_LED_WAN_G,
+               .active_low     = 1,
+       },
+};
+
+static struct gpio_led e600gac_v2_leds_gpio[] __initdata = {
+       {
+               .name           = "e600gac-v2:blue:control",
+               .gpio           = E600GAC_V2_GPIO_LED_CTRL_B,
+               .active_low     = 1,
+       }, {
+               .name           = "e600gac-v2:green:control",
+               .gpio           = E600GAC_V2_GPIO_LED_CTRL_G,
+               .active_low     = 1,
+       }, {
+               .name           = "e600gac-v2:red:control",
+               .gpio           = E600GAC_V2_GPIO_LED_CTRL_R,
+               .active_low     = 1,
+       }, {
+               .name           = "e600gac-v2:green:system",
+               .gpio           = E600GAC_V2_GPIO_LED_SYS,
+               .active_low     = 1,
+       }, {
+               .name           = "e600gac-v2:orange:wan",
+               .gpio           = E600GAC_V2_GPIO_LED_WAN_O,
+               .active_low     = 1,
+       }, {
+               .name           = "e600gac-v2:green:lan",
+               .gpio           = E600GAC_V2_GPIO_LED_LAN,
+               .active_low     = 1,
+       }, {
+               .name           = "e600gac-v2:green:wan",
+               .gpio           = E600GAC_V2_GPIO_LED_WAN_G,
+               .active_low     = 1,
+       },
+};
+
+static struct gpio_keys_button e600g_v2_gpio_keys[] __initdata = {
+       {
+               .desc                   = "reset",
+               .type                   = EV_KEY,
+               .code                   = KEY_RESTART,
+               .debounce_interval      = E600G_V2_KEYS_DEBOUNCE_INTERVAL,
+               .gpio                   = E600G_V2_GPIO_BTN_RESET,
+               .active_low             = 1,
+       },
+};
+
+static struct gpio_keys_button e600gac_v2_gpio_keys[] __initdata = {
+       {
+               .desc                   = "reset",
+               .type                   = EV_KEY,
+               .code                   = KEY_RESTART,
+               .debounce_interval      = E600G_V2_KEYS_DEBOUNCE_INTERVAL,
+               .gpio                   = E600G_V2_GPIO_BTN_RESET,
+               .active_low             = 1,
+       }, {
+               .desc                   = "wps",
+               .type                   = EV_KEY,
+               .code                   = KEY_WPS_BUTTON,
+               .debounce_interval      = E600G_V2_KEYS_DEBOUNCE_INTERVAL,
+               .gpio                   = E600GAC_V2_GPIO_BTN_WPS,
+               .active_low             = 1,
+       },
+};
+
+static void __init e600g_v2_common_setup(void)
+{
+       u8 *mac = (u8 *) KSEG1ADDR(0x1f050400);
+       u8 *art = (u8 *) KSEG1ADDR(0x1f061000);
+
+       ath79_register_m25p80(NULL);
+
+       ath79_setup_ar933x_phy4_switch(false, false);
+
+       ath79_register_mdio(0, 0x0);
+
+       ath79_switch_data.phy4_mii_en = 1;
+       ath79_switch_data.phy_poll_mask = 0xfe;
+
+       /* LAN */
+       ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+       ath79_eth0_data.phy_mask = BIT(4);
+       ath79_eth0_data.speed = SPEED_100;
+       ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1);
+       ath79_register_eth(0);
+
+       /* WAN */
+       ath79_eth1_data.duplex = DUPLEX_FULL;
+       ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+       ath79_eth1_data.phy_mask = BIT(0);
+       ath79_eth1_data.speed = SPEED_1000;
+       ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0);
+       ath79_register_eth(1);
+
+       ath79_register_pci();
+       ath79_register_usb();
+       ath79_register_wmac(art, NULL);
+}
+
+static void __init e600g_v2_setup(void)
+{
+       e600g_v2_common_setup();
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(e600g_v2_leds_gpio),
+                                e600g_v2_leds_gpio);
+
+       ath79_register_gpio_keys_polled(-1, E600G_V2_KEYS_POLL_INTERVAL,
+                                       ARRAY_SIZE(e600g_v2_gpio_keys),
+                                       e600g_v2_gpio_keys);
+}
+
+static void __init e600gac_v2_setup(void)
+{
+       e600g_v2_common_setup();
+
+       ath79_register_leds_gpio(-1, ARRAY_SIZE(e600gac_v2_leds_gpio),
+                                e600gac_v2_leds_gpio);
+
+       ath79_register_gpio_keys_polled(-1, E600G_V2_KEYS_POLL_INTERVAL,
+                                       ARRAY_SIZE(e600gac_v2_gpio_keys),
+                                       e600gac_v2_gpio_keys);
+}
+
+MIPS_MACHINE(ATH79_MACH_E600G_V2, "E600G-V2", "WHQX E600G v2",
+            e600g_v2_setup);
+
+MIPS_MACHINE(ATH79_MACH_E600GAC_V2, "E600GAC-V2", "WHQX E600GAC v2",
+            e600gac_v2_setup);
index 497d794..e22ebd0 100644 (file)
@@ -98,6 +98,9 @@ enum ath79_mach_type {
        ATH79_MACH_DR344,                       /* Wallys DR344 */
        ATH79_MACH_DR531,                       /* Wallys DR531 */
        ATH79_MACH_DRAGINO2,                    /* Dragino Version 2 */
+       ATH79_MACH_E1700AC_V2,                  /* WHQX E1700AC v2 */
+       ATH79_MACH_E600G_V2,                    /* WHQX E600G v2 */
+       ATH79_MACH_E600GAC_V2,                  /* WHQX E600GAC v2 */
        ATH79_MACH_EAP120,                      /* TP-LINK EAP120 */
        ATH79_MACH_EAP300V2,                    /* EnGenius EAP300 v2 */
        ATH79_MACH_EAP7660D,                    /* Senao EAP7660D */
index 9caf29a..2e5eb66 100644 (file)
@@ -70,7 +70,9 @@ CONFIG_ATH79_MACH_DR342=y
 CONFIG_ATH79_MACH_DR344=y
 CONFIG_ATH79_MACH_DR531=y
 CONFIG_ATH79_MACH_DRAGINO2=y
+CONFIG_ATH79_MACH_E1700AC_V2=y
 CONFIG_ATH79_MACH_E2100L=y
+CONFIG_ATH79_MACH_E600G_V2=y
 CONFIG_ATH79_MACH_EAP120=y
 CONFIG_ATH79_MACH_EAP300V2=y
 CONFIG_ATH79_MACH_EAP7660D=y
index eeefde0..beb56bd 100644 (file)
@@ -281,6 +281,65 @@ define Device/dragino2
 endef
 TARGET_DEVICES += dragino2
 
+define Device/e1700ac-v2-16M
+  DEVICE_TITLE := WHQX E1700AC v2 (16MB flash)
+  DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x kmod-usb-core \
+       kmod-usb2 kmod-usb-ledtrig-usbport
+  BOARDNAME := E1700AC-V2
+  SUPPORTED_DEVICES := e1700ac-v2
+  IMAGE_SIZE := 15936k
+  MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art)ro,-(firmware)
+  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+       append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e1700ac-v2-16M
+
+define Device/e1700ac-v2-8M
+  $(Device/e1700ac-v2-16M)
+  DEVICE_TITLE := WHQX E1700AC v2 (8MB flash)
+  IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e1700ac-v2-8M
+
+define Device/e600g-v2-16M
+  DEVICE_TITLE := WHQX E600G v2 (16MB flash)
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 -swconfig
+  BOARDNAME := E600G-V2
+  SUPPORTED_DEVICES := e600g-v2
+  IMAGE_SIZE := 15936k
+  MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art)ro,-(firmware)
+  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+       append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e600g-v2-16M
+
+define Device/e600g-v2-8M
+  $(Device/e600g-v2-16M)
+  DEVICE_TITLE := WHQX E600G v2 (8MB flash)
+  IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e600g-v2-8M
+
+define Device/e600gac-v2-16M
+  DEVICE_TITLE := WHQX E600GAC v2 (16MB flash)
+  DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca9887 kmod-usb-core \
+       kmod-usb2 -swconfig
+  BOARDNAME := E600GAC-V2
+  SUPPORTED_DEVICES := e600gac-v2
+  IMAGE_SIZE := 15936k
+  MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(pri-data)ro,64k(art)ro,-(firmware)
+  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+       append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += e600gac-v2-16M
+
+define Device/e600gac-v2-8M
+  $(Device/e600gac-v2-16M)
+  DEVICE_TITLE := WHQX E600GAC v2 (8MB flash)
+  IMAGE_SIZE := 7744k
+endef
+TARGET_DEVICES += e600gac-v2-8M
+
 define Device/ew-balin
   DEVICE_TITLE := Embedded Wireless Balin Platform
   DEVICE_PACKAGES := kmod-usb-core kmod-usb-chipidea