ramips: add support for Ubiquiti UniFi FlexHD
authorSven Wegener <sven.wegener@stealer.net>
Sat, 1 May 2021 11:51:51 +0000 (13:51 +0200)
committerDaniel Golle <daniel@makrotopia.org>
Sun, 18 Sep 2022 14:40:04 +0000 (15:40 +0100)
Hardware
--------

- SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash
- Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4)
- Bluetooth: CSR8811 (internal USB, install kmod-bluetooth)

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Update the bootloader environment.

   $ fw_setenv devmode TRUE
   $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
     fdt rm /signature; bootubnt"
   $ fw_setenv bootcmd "run boot_openwrt"

3. Transfer the OpenWrt sysupgrade image to the device using SCP.

4. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

5. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4

6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock6
   $ dd if=openwrt.bin of=/dev/mtdblock7

7. Reboot the device. It should boot into OpenWrt.

Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 820f0c07c544652c1c53a45262a481ac5dbe139b)

target/linux/ramips/dts/mt7621_ubnt_unifi-flexhd.dts [new file with mode: 0644]
target/linux/ramips/image/mt7621.mk
target/linux/ramips/mt7621/base-files/etc/board.d/02_network
target/linux/ramips/mt7621/config-5.10

diff --git a/target/linux/ramips/dts/mt7621_ubnt_unifi-flexhd.dts b/target/linux/ramips/dts/mt7621_ubnt_unifi-flexhd.dts
new file mode 100644 (file)
index 0000000..615bdf4
--- /dev/null
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "ubnt,unifi-flexhd", "mediatek,mt7621-soc";
+       model = "Ubiquiti UniFi FlexHD";
+
+       aliases {
+               label-mac-device = &gmac0;
+               led-boot = &led_blue;
+               led-failsafe = &led_blue;
+               led-running = &led_blue;
+               led-upgrade = &led_blue;
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,115200";
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+       };
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <50000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x60000>;
+                               read-only;
+                       };
+
+                       partition@60000 {
+                               label = "u-boot-env";
+                               reg = <0x60000 0x10000>;
+                               read-only;
+                       };
+
+                       factory: partition@70000 {
+                               label = "factory";
+                               reg = <0x70000 0x10000>;
+                               read-only;
+                       };
+
+                       eeprom: partition@80000 {
+                               label = "eeprom";
+                               reg = <0x80000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@90000 {
+                               label = "bs";
+                               reg = <0x90000 0x10000>;
+                       };
+
+                       partition@a0000 {
+                               label = "cfg";
+                               reg = <0xa0000 0x100000>;
+                               read-only;
+                       };
+
+                       partition@1a0000 {
+                               compatible = "denx,fit";
+                               label = "firmware";
+                               reg = <0x1a0000 0xf30000>;
+                       };
+
+                       partition@10d0000 {
+                               label = "kernel1";
+                               reg = <0x10d0000 0xf30000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&eeprom {
+       compatible = "nvmem-cells";
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       macaddr_eeprom_0: macaddr@0 {
+               reg = <0x0 0x6>;
+       };
+};
+
+&gmac0 {
+       nvmem-cells = <&macaddr_eeprom_0>;
+       nvmem-cell-names = "mac-address";
+};
+
+&switch0 {
+       ports {
+               port@0 {
+                       status = "okay";
+                       label = "lan";
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&pcie0 {
+       wifi@0,0 {
+               reg = <0x0 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x0>;
+               // On newer devices there is a MediaTek MAC in the above
+               // device EEPROM, so override it with a calculated one.
+               nvmem-cells = <&macaddr_eeprom_0>;
+               nvmem-cell-names = "mac-address";
+               mac-address-increment = <1>;
+       };
+};
+
+&pcie1 {
+       wifi@0,0 {
+               reg = <0x0 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x8000>;
+               // On newer devices there is a MediaTek MAC in the above
+               // device EEPROM, so override it with a calculated one.
+               nvmem-cells = <&macaddr_eeprom_0>;
+               nvmem-cell-names = "mac-address";
+               mac-address-increment = <2>;
+       };
+};
+
+&i2c {
+       status = "okay";
+       clock-frequency = <400000>;
+
+       led-controller@30 {
+               compatible = "ubnt,ledbar";
+               reg = <0x30>;
+
+               enable-gpio = <&gpio 44 GPIO_ACTIVE_HIGH>;
+               reset-gpio = <&gpio 41 GPIO_ACTIVE_LOW>;
+               led-count = <8>;
+
+               red {
+                       label = "red";
+               };
+
+               green {
+                       label = "green";
+               };
+
+               led_blue: blue {
+                       label = "blue";
+               };
+       };
+};
+
+&state_default {
+       gpio {
+               groups = "uart2";
+               function = "gpio";
+       };
+};
index 7f903485aa9e3055ae0bb490bb8e6d5aab565b45..8860be11b8c879c067901cf6642a133b27b1e3b2 100644 (file)
@@ -1785,6 +1785,17 @@ define Device/ubnt_unifi-6-lite
 endef
 TARGET_DEVICES += ubnt_unifi-6-lite
 
+define Device/ubnt_unifi-flexhd
+  $(Device/dsa-migration)
+  DEVICE_VENDOR := Ubiquiti
+  DEVICE_MODEL := UniFi FlexHD
+  DEVICE_DTS_CONFIG := config@2
+  KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  DEVICE_PACKAGES += kmod-mt7603 kmod-mt7615e kmod-mt7615-firmware
+  IMAGE_SIZE := 15552k
+endef
+TARGET_DEVICES += ubnt_unifi-flexhd
+
 define Device/ubnt_unifi-nanohd
   $(Device/dsa-migration)
   DEVICE_VENDOR := Ubiquiti
index 2a08aded3456bcf951ba6a3349206696b1c6373d..ad560a4ec09083398b25e561ec4793762b7db012 100644 (file)
@@ -20,6 +20,7 @@ ramips_setup_interfaces()
        tplink,re650-v1|\
        tplink,re650-v2|\
        ubnt,unifi-6-lite|\
+       ubnt,unifi-flexhd|\
        ubnt,unifi-nanohd)
                ucidef_set_interface_lan "lan"
                ;;
index ec6822fa6d2f8b3cc9bdf4a1795c80426723b6de..dd23f13bc62b63472ebeabb579035fa41b8302db 100644 (file)
@@ -111,6 +111,7 @@ CONFIG_IRQ_MIPS_CPU=y
 CONFIG_IRQ_WORK=y
 # CONFIG_KERNEL_ZSTD is not set
 CONFIG_LED_TRIGGER_PHY=y
+CONFIG_LEDS_UBNT_LEDBAR=y
 CONFIG_LIBFDT=y
 CONFIG_LOCK_DEBUGGING_SUPPORT=y
 CONFIG_LZO_COMPRESS=y