disable powersave, vlynq can't handle this
authorMatteo Croce <rootkit85@yahoo.it>
Mon, 17 Sep 2007 00:08:24 +0000 (00:08 +0000)
committerMatteo Croce <rootkit85@yahoo.it>
Mon, 17 Sep 2007 00:08:24 +0000 (00:08 +0000)
SVN-Revision: 8818

package/acx-mac80211/patches/011-no_pm.patch [new file with mode: 0644]
package/acx/patches/011-no_pm.patch [new file with mode: 0644]

diff --git a/package/acx-mac80211/patches/011-no_pm.patch b/package/acx-mac80211/patches/011-no_pm.patch
new file mode 100644 (file)
index 0000000..09a00b0
--- /dev/null
@@ -0,0 +1,32 @@
+--- acx-mac80211-20070610/pci.c        2007-06-10 20:23:27.000000000 +0200
++++ acx-mac80211-20070610.new/pci.c    2007-09-17 01:07:38.000000000 +0200
+@@ -1693,7 +1693,9 @@
+ /** done with board specific setup **/
+       /* need to be able to restore PCI state after a suspend */
++#ifdef CONFIG_PM
+       pci_save_state(pdev);
++#endif
+       acx_init_task_scheduler(adev);
+@@ -1740,7 +1742,9 @@
+       pci_disable_device(pdev);
+       fail_pci_enable_device:
++#ifdef CONFIG_PM
+       pci_set_power_state(pdev, PCI_D3hot);
++#endif
+       fail_register_netdev:
+       ieee80211_free_hw(ieee);
+       done:
+@@ -1872,7 +1876,9 @@
+       ieee80211_free_hw(adev->ieee);
+       /* put device into ACPI D3 mode (shutdown) */
++#ifdef CONFIG_PM
+       pci_set_power_state(pdev, PCI_D3hot);
++#endif
+ //    kfree(ieee);
+       end:
+       FN_EXIT0;
diff --git a/package/acx/patches/011-no_pm.patch b/package/acx/patches/011-no_pm.patch
new file mode 100644 (file)
index 0000000..d1d0feb
--- /dev/null
@@ -0,0 +1,33 @@
+diff -ruN acx-20070610-old/pci.c acx-20070610-new/pci.c
+--- acx-20070610-old/pci.c     2007-09-16 17:57:55.000000000 +0200
++++ acx-20070610-new/pci.c     2007-09-16 17:59:25.000000000 +0200
+@@ -1630,7 +1630,9 @@
+       log(L_IRQ|L_INIT, "using IRQ %d\n", pdev->irq);
+       /* need to be able to restore PCI state after a suspend */
++#ifdef CONFIG_PM
+       pci_save_state(pdev);
++#endif
+       pci_set_drvdata(pdev, ndev);
+       /* ok, pci setup is finished, now start initializing the card */
+@@ -1728,7 +1730,9 @@
+       pci_disable_device(pdev);
+ fail_pci_enable_device:
++#ifdef CONFIG_PM
+       pci_set_power_state(pdev, PCI_D3hot);
++#endif
+ done:
+       FN_EXIT1(result);
+@@ -1848,7 +1852,9 @@
+       free_netdev(ndev);
+       /* put device into ACPI D3 mode (shutdown) */
++#ifdef CONFIG_PM
+       pci_set_power_state(pdev, PCI_D3hot);
++#endif
+ end:
+       FN_EXIT0;