target/linux/ath79/dts/ar7241_ubnt_xm.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "ar7241.dtsi"
   7
   8 / {
   9         compatible = "ubnt,xm", "qca,ar7241";
  10         model = "Ubiquiti Networks XM (rev 1.0) board";
  11
  12 /*      extosc: ref {
  13                 compatible = "fixed-clock";
  14                 #clock-cells = <0>;
  15                 clock-frequency = <40000000>;
  16         };
  17 */
  18         keys {
  19                 compatible = "gpio-keys-polled";
  20                 #address-cells = <1>;
  21                 #size-cells = <0>;
  22
  23                 poll-interval = <20>;
  24                 reset {
  25                         linux,code = <KEY_RESTART>;
  26                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  27                         debounce-interval = <60>;
  28                 };
  29         };
  30
  31         leds {
  32                 compatible = "gpio-leds";
  33                 link1 {
  34                         label = "ubnt:red:link1";
  35                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  36                 };
  37
  38                 link2 {
  39                         label = "ubnt:orange:link2";
  40                         gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
  41                 };
  42
  43                 link3 {
  44                         label = "ubnt:green:link3";
  45                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  46                 };
  47
  48                 link4 {
  49                         label = "ubnt:green:link4";
  50                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  51                 };
  52         };
  53 };
  54
  55 &uart {
  56         status = "okay";
  57 };
  58
  59 /*&pll {
  60         clocks = <&extosc>;
  61 };*/
  62
  63 &spi {
  64         status = "okay";
  65         num-cs = <1>;
  66
  67         flash@0 {
  68                 #address-cells = <1>;
  69                 #size-cells = <1>;
  70                 compatible = "mx25l6405d";
  71                 reg = <0>;
  72                 spi-max-frequency = <25000000>;
  73
  74                 partitions {
  75                         compatible = "fixed-partitions";
  76                         #address-cells = <1>;
  77                         #size-cells = <1>;
  78
  79                         partition@0 {
  80                                 label = "u-boot";
  81                                 reg = <0x000000 0x040000>;
  82                                 read-only;
  83                         };
  84
  85                         partition@1 {
  86                                 label = "u-boot-env";
  87                                 reg = <0x040000 0x010000>;
  88                         };
  89
  90                         partition@2 {
  91                                 label = "firmware";
  92                                 reg = <0x050000 0x750000>;
  93                         };
  94
  95                         partition@3 {
  96                                 label = "board_config";
  97                                 reg = <0x7a0000 0x010000>;
  98                                 read-only;
  99                         };
 100
 101                         partition@4 {
 102                                 label = "cfg";
 103                                 reg = <0x7b0000 0x040000>;
 104                                 read-only;
 105                         };
 106
 107                         art: partition@5 {
 108                                 label = "art";
 109                                 reg = <0x7f0000 0x010000>;
 110                                 read-only;
 111                         };
 112                 };
 113         };
 114 };
 115
 116 &pcie {
 117         status = "okay";
 118
 119         ath9k@0 {
 120                 reg = <0x0000 0 0 0 0>;
 121                 qca,no-eeprom;
 122         };
 123 };
 124
 125 &mdio0 {
 126         status = "okay";
 127
 128         phy4: ethernet-phy@4 {
 129                 reg = <4>;
 130                 phy-mode = "mii";
 131         };
 132 };
 133
 134 &eth0 {
 135         status = "okay";
 136
 137         mtd-mac-address = <&art 0x0>;
 138
 139         phy-mode = "mii";
 140         phy-handle = <&phy4>;
 141 };
 142
 143 &eth1 {
 144         status = "okay";
 145
 146         mtd-mac-address = <&art 0x6>;
 147 };