ath79: add support for jjPlus JA76PF2
authorTomasz Maciej Nowak <tomek_n@o2.pl>
Wed, 6 Mar 2019 19:15:19 +0000 (20:15 +0100)
committerChristian Lamparter <chunkeey@gmail.com>
Mon, 18 Mar 2019 19:43:09 +0000 (20:43 +0100)
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.

Specification
SoC: Atheros AR7161
RAM: 64 MB DDR
Flash: 16 MB SPI NOR
Ethernet: 2x 10/100/1000 Mbps AR8316
LAN (CN11), WAN/PoE (CN6 - close to power barrel
connector, 48 V)
MiniPCI: 2x
LEDS: 4x, which 3 are GPIO controlled
Buttons: 2x GPIO controlled
Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial: 1x (only RX and TX are wired)
baud: 115200, parity: none, flow control: none

Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.

Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
   process and enter RedBoot (bootloader) command line by pressing
   Ctrl+C,
4. Enter following commands (replace variable accordingly),
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_adress>
    (confirm storing the value by inputting y and pressing Enter)
    reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.

Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
   pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_address>
    (confirm storing the value by inputting y and pressing Enter)
    ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
    load -r -b 0x80060000 <openwrt_initramfs_image_name>
    exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
   is ready for configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/base-files/lib/upgrade/platform.sh
target/linux/ath79/dts/ar7161_jjplus_ja76pf2.dts [new file with mode: 0644]
target/linux/ath79/generic/config-default
target/linux/ath79/image/generic.mk
target/linux/ath79/patches-4.14/408-mtd-redboot_partition_scan.patch [new file with mode: 0644]

index e2c303e56572743c21136fca9baa5a6f98201290..62318ee2320cc6762f0568ee09b08eca92023b8c 100755 (executable)
@@ -288,6 +288,10 @@ ath79_setup_macs()
                lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
                wan_mac=$(macaddr_add "$lan_mac" -1)
                ;;
+       jjplus,ja76pf2)
+               wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n alias/ethaddr)
+               lan_mac=$(macaddr_add "$wan_mac" 1)
+               ;;
        nec,wg800hp)
                lan_mac=$(mtd_get_mac_text board_data 640)
                wan_mac=$(mtd_get_mac_text board_data 1152)
index bc19149d5c4de5a32984f34b27d1e9ce15c9593d..c2fe08154d9e297fc4c79443465257af0ef3290b 100644 (file)
@@ -5,9 +5,10 @@
 PART_NAME=firmware
 REQUIRE_IMAGE_METADATA=1
 
-routerstation_do_upgrade() {
+redboot_fis_do_upgrade() {
        local append
        local sysup_file="$1"
+       local kern_part="$2"
        local magic=$(get_magic_word "$sysup_file")
 
        if [ "$magic" = "4349" ]; then
@@ -15,7 +16,7 @@ routerstation_do_upgrade() {
 
                [ -f "$CONF_TAR" -a "$SAVE_CONFIG" -eq 1 ] && append="-j $CONF_TAR"
                dd if="$sysup_file" bs=64k skip=1 2>/dev/null | \
-                       mtd -r $append -Fkernel:$kern_length:0x80060000,rootfs write - kernel:rootfs
+                       mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
 
        elif [ "$magic" = "7379" ]; then
                local board_dir=$(tar tf $sysup_file | grep -m 1 '^sysupgrade-.*/$')
@@ -23,7 +24,7 @@ routerstation_do_upgrade() {
 
                [ -f "$CONF_TAR" -a "$SAVE_CONFIG" -eq 1 ] && append="-j $CONF_TAR"
                tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
-                       mtd -r $append -Fkernel:$kern_length:0x80060000,rootfs write - kernel:rootfs
+                       mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
 
        else
                echo "Unknown image, aborting!"
@@ -39,9 +40,12 @@ platform_do_upgrade() {
        local board=$(board_name)
 
        case "$board" in
+       jjplus,ja76pf2)
+               redboot_fis_do_upgrade "$ARGV" linux
+               ;;
        ubnt,routerstation|\
        ubnt,routerstation-pro)
-               routerstation_do_upgrade "$ARGV"
+               redboot_fis_do_upgrade "$ARGV" kernel
                ;;
        *)
                default_do_upgrade "$ARGV"
diff --git a/target/linux/ath79/dts/ar7161_jjplus_ja76pf2.dts b/target/linux/ath79/dts/ar7161_jjplus_ja76pf2.dts
new file mode 100644 (file)
index 0000000..76f140f
--- /dev/null
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7100.dtsi"
+
+/ {
+       model = "jjPlus JA76PF2";
+       compatible = "jjplus,ja76pf2", "qca,ar7161";
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x0 0x4000000>;
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,115200n8";
+       };
+
+       aliases {
+               led-boot = &d2;
+               led-failsafe = &d2;
+               led-running = &d2;
+               led-upgrade = &d2;
+       };
+
+       extosc: ref {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-output-names = "ref";
+               clock-frequency = <40000000>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               d2: d2 {
+                       label = "ja76pf2:green:d2";
+                       gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+               };
+
+               d3 {
+                       label = "ja76pf2:green:d3";
+                       gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+               };
+
+               d4 {
+                       label = "ja76pf2:green:d4";
+                       gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys-polled";
+               poll-interval = <20>;
+
+               sw1 {
+                       label = "sw1";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+
+               sw2 {
+                       label = "sw2";
+                       linux,code = <KEY_WPS_BUTTON>;
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy-mask = <0x1>;
+
+       phy0: ethernet-phy@0 {
+               reg = <0>;
+               phy-mode = "rgmii";
+       };
+
+       phy4: ethernet-phy@4 {
+               reg = <4>;
+               phy-mode = "rgmii";
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       phy-handle = <&phy0>;
+};
+
+&eth1 {
+       status = "okay";
+
+       phy-handle = <&phy4>;
+};
+
+&pcie0 {
+       status = "okay";
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <104000000>;
+
+               partitions {
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       compatible = "ecoscentric,redboot-fis-partitions";
+               };
+       };
+};
+
+&uart {
+       status = "okay";
+};
index fddcb1d704b65a080765c9bba0912a846706d48f..313ab8604bd0096b47484c2e990373c6c13cfc2a 100644 (file)
@@ -8,6 +8,7 @@ CONFIG_LEDS_RESET=y
 CONFIG_MARVELL_PHY=y
 CONFIG_MICREL_PHY=y
 CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
 CONFIG_MTD_SPLIT_EVA_FW=y
 CONFIG_OF_ADDRESS_PCI=y
 CONFIG_OF_PCI=y
index 6b20b66669c4a4287cf9c3111ce2393d3419ca48..ddf0e62898bf210a63ea997f24f7cb1f3fcc1a49 100644 (file)
@@ -417,6 +417,18 @@ define Device/iodata_wn-ag300dgr
 endef
 TARGET_DEVICES += iodata_wn-ag300dgr
 
+define Device/jjplus_ja76pf2
+  ATH_SOC := ar7161
+  DEVICE_TITLE := jjPlus JA76PF2
+  DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-mini -uboot-envtools fconfig
+  IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | check-size $$$$(IMAGE_SIZE)
+#  IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
+  KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
+  KERNEL_INITRAMFS := kernel-bin | append-dtb
+  IMAGE_SIZE := 16000k
+endef
+TARGET_DEVICES += jjplus_ja76pf2
+
 define Device/librerouter_librerouter-v1
   ATH_SOC := qca9558
   DEVICE_TITLE := LibreRouter v1
diff --git a/target/linux/ath79/patches-4.14/408-mtd-redboot_partition_scan.patch b/target/linux/ath79/patches-4.14/408-mtd-redboot_partition_scan.patch
new file mode 100644 (file)
index 0000000..cd41e7c
--- /dev/null
@@ -0,0 +1,44 @@
+--- a/drivers/mtd/redboot.c
++++ b/drivers/mtd/redboot.c
+@@ -76,12 +76,18 @@ static int parse_redboot_partitions(stru
+       static char nullstring[] = "unallocated";
+ #endif
++      buf = vmalloc(master->erasesize);
++      if (!buf)
++              return -ENOMEM;
++
++ restart:
+       if ( directory < 0 ) {
+               offset = master->size + directory * master->erasesize;
+               while (mtd_block_isbad(master, offset)) {
+                       if (!offset) {
+                       nogood:
+                               printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
++                              vfree(buf);
+                               return -EIO;
+                       }
+                       offset -= master->erasesize;
+@@ -94,10 +100,6 @@ static int parse_redboot_partitions(stru
+                               goto nogood;
+               }
+       }
+-      buf = vmalloc(master->erasesize);
+-
+-      if (!buf)
+-              return -ENOMEM;
+       printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
+              master->name, offset);
+@@ -170,6 +172,11 @@ static int parse_redboot_partitions(stru
+       }
+       if (i == numslots) {
+               /* Didn't find it */
++              if (offset + master->erasesize < master->size) {
++                      /* not at the end of the flash yet, maybe next block :) */
++                      directory++;
++                      goto restart;
++              }
+               printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
+                      master->name);
+               ret = 0;