3 #include <dt-bindings/input/input.h>
6 compatible = "arcadyan,arv7510pw22", "lantiq,xway", "lantiq,danube";
7 model = "Astoria Networks ARV7510PW22";
10 bootargs = "console=ttyLTQ0,115200";
15 led-failsafe = &power;
25 device_type = "memory";
26 reg = <0x0 0x4000000>;
30 compatible = "gpio-keys-polled";
31 poll-interval = <100>;
35 gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
36 linux,code = <KEY_RFKILL>;
40 gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
41 linux,code = <KEY_POWER>;
45 gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
46 linux,code = <KEY_RESTART>;
51 compatible = "gpio-leds";
54 gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
55 default-state = "keep";
59 gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
63 gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
67 gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
71 gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
75 usb_vbus: regulator-usb-vbus {
76 compatible = "regulator-fixed";
78 regulator-name = "USB_VBUS";
80 regulator-min-microvolt = <5000000>;
81 regulator-max-microvolt = <5000000>;
83 gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
89 pinctrl-names = "default";
90 pinctrl-0 = <&state_default>;
92 state_default: pinmux {
94 lantiq,groups = "exin1";
95 lantiq,function = "exin";
100 lantiq,pins = "io21";
105 lantiq,pins = "io2", "io4", "io8", "io9", "io10", "io15", "io20";
109 lantiq,pins = "io11", "io12", "io28";
110 lantiq,open-drain = <1>;
118 /* Switch reset 19 */
120 nvmem-cells = <&macaddr_boardconfig_16>;
121 nvmem-cell-names = "mac-address";
126 compatible = "lantiq,nor";
128 reg = <0 0x0 0x1000000>;
131 compatible = "fixed-partitions";
132 #address-cells = <1>;
137 reg = <0x00000 0x40000>;
142 label = "u-boot-env";
143 reg = <0x40000 0x20000>;
149 reg = <0x60000 0xf80000>;
152 boardconfig: partition@fe0000 {
153 label = "board_config";
154 reg = <0xfe0000 0x20000>;
158 compatible = "fixed-layout";
159 #address-cells = <1>;
162 macaddr_boardconfig_16: macaddr@16 {
174 pinctrl-0 = <&pci_gnt1_pins>, <&pci_req1_pins>, <&pci_req2_pins>;
175 pinctrl-names = "default";
177 lantiq,external-clock;
179 0x7000 0 0 1 &icu0 30
180 0x7800 0 0 1 &icu0 135
181 0x7800 0 0 2 &icu0 135
182 0x7800 0 0 3 &icu0 135
184 gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
188 compatible = "pci1814,3592";
189 reg = <0x7000 0 0 0 0>;
190 ralink,mtd-eeprom = <&boardconfig 0x410>;
201 vbus-supply = <&usb_vbus>;
206 gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;