target/linux/ramips/dts/AR670W.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/input/input.h>
   6
   7 / {
   8         compatible = "AR670W", "ralink,rt2880-soc";
   9         model = "Airlink101 AR670W";
  10
  11         cfi@bdc00000 {
  12                 compatible = "cfi-flash";
  13                 reg = <0xbc400000 0x800000>;
  14                 bank-width = <2>;
  15                 #address-cells = <1>;
  16                 #size-cells = <1>;
  17
  18                 u-boot@0 {
  19                         reg = <0x0 0x30000>;
  20                         label = "u-boot";
  21                         read-only;
  22                 };
  23
  24                 factory: factory@30000 {
  25                         reg = <0x30000 0x10000>;
  26                         label = "factory";
  27                         read-only;
  28                 };
  29
  30                 firmware@40000 {
  31                         reg = <0x40000 0x3c0000>;
  32                         label = "firmware";
  33                 };
  34         };
  35
  36         gpio-leds {
  37                 compatible = "gpio-leds";
  38
  39                 status {
  40                         label = "ar670w:green:power";
  41                         gpios = <&gpio0 7 1>;
  42                 };
  43
  44                 wpsblue {
  45                         label = "ar670w:blue:wps";
  46                         gpios = <&gpio0 13 1>;
  47                 };
  48         };
  49
  50         gpio-keys-polled {
  51                 compatible = "gpio-keys-polled";
  52                 #address-cells = <1>;
  53                 #size-cells = <0>;
  54                 poll-interval = <100>;
  55
  56                 wps {
  57                         label = "wps";
  58                         gpios = <&gpio0 0 1>;
  59                         linux,code = <KEY_WPS_BUTTON>;
  60                 };
  61
  62                 reset {
  63                         label = "reset";
  64                         gpios = <&gpio0 9 1>;
  65                         linux,code = <KEY_RESTART>;
  66                 };
  67         };
  68 };
  69
  70 &gpio0 {
  71         status = "okay";
  72 };
  73
  74 &pinctrl {
  75         state_default: pinctrl0 {
  76                 gpio {
  77                         ralink,group = "i2c", "spi", "uartlite";
  78                         ralink,function = "gpio";
  79                 };
  80         };
  81 };
  82
  83 &ethernet {
  84         status = "okay";
  85         mtd-mac-address = <&factory 0x2004>;
  86
  87         port@0 {
  88                 phy-handle = <&phy0>;
  89                 phy-mode = "mii";
  90         };
  91
  92         mdio-bus {
  93                 status = "okay";
  94
  95                 phy0: ethernet-phy@0 {
  96                         phy-mode = "mii";
  97                         reg = <0>;
  98                 };
  99         };
 100 };
 101
 102 &wmac {
 103         status = "okay";
 104         ralink,mtd-eeprom = <&factory 0x2000>;
 105 };