target/linux/ath79/dts/ar9331_tplink_tl-wr703n_tl-mr10u.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "ar9331.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         aliases {
  10                 led-boot = &led_system;
  11                 led-failsafe = &led_system;
  12                 led-running = &led_system;
  13                 led-upgrade = &led_system;
  14                 label-mac-device = &eth0;
  15         };
  16
  17         keys {
  18                 compatible = "gpio-keys";
  19
  20                 reset {
  21                         label = "reset";
  22                         linux,code = <KEY_RESTART>;
  23                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  24                         debounce-interval = <60>;
  25                 };
  26         };
  27
  28         leds {
  29                 compatible = "gpio-leds";
  30
  31                 led_system: system {
  32                         label = "blue:system";
  33                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  34                 };
  35         };
  36
  37         reg_usb_vbus: reg_usb_vbus {
  38                 compatible = "regulator-fixed";
  39                 regulator-name = "usb_vbus";
  40                 regulator-min-microvolt = <5000000>;
  41                 regulator-max-microvolt = <5000000>;
  42                 enable-active-high;
  43         };
  44 };
  45
  46 &spi {
  47         status = "okay";
  48
  49         flash@0 {
  50                 compatible = "jedec,spi-nor";
  51                 reg = <0>;
  52                 spi-max-frequency = <25000000>;
  53
  54                 partitions {
  55                         compatible = "fixed-partitions";
  56                         #address-cells = <1>;
  57                         #size-cells = <1>;
  58
  59                         uboot: partition@0 {
  60                                 reg = <0x0 0x20000>;
  61                                 label = "u-boot";
  62                                 read-only;
  63
  64                                 nvmem-layout {
  65                                         compatible = "fixed-layout";
  66                                         #address-cells = <1>;
  67                                         #size-cells = <1>;
  68
  69                                         macaddr_uboot_1fc00: macaddr@1fc00 {
  70                                                 reg = <0x1fc00 0x6>;
  71                                         };
  72                                 };
  73                         };
  74
  75                         partition@20000 {
  76                                 compatible = "tplink,firmware";
  77                                 reg = <0x20000 0x3d0000>;
  78                                 label = "firmware";
  79                         };
  80
  81                         art: partition@3f0000 {
  82                                 reg = <0x3f0000 0x10000>;
  83                                 label = "art";
  84                                 read-only;
  85                         };
  86                 };
  87         };
  88 };
  89
  90 &eth0 {
  91         status = "okay";
  92
  93         nvmem-cells = <&macaddr_uboot_1fc00>;
  94         nvmem-cell-names = "mac-address";
  95
  96         gmac-config {
  97                 device = <&gmac>;
  98
  99                 switch-phy-addr-swap = <0>;
 100                 switch-phy-swap = <0>;
 101         };
 102 };
 103
 104 &eth1 {
 105         status = "okay";
 106
 107         compatible = "syscon", "simple-mfd";
 108 };
 109
 110 &usb {
 111         dr_mode = "host";
 112         vbus-supply = <&reg_usb_vbus>;
 113         status = "okay";
 114 };
 115
 116 &usb_phy {
 117         status = "okay";
 118 };
 119
 120 &wmac {
 121         status = "okay";
 122
 123         mtd-cal-data = <&art 0x1000>;
 124         nvmem-cells = <&macaddr_uboot_1fc00>;
 125         nvmem-cell-names = "mac-address";
 126 };